coolant level MAZDA MODEL CX-30 2019 Owners Manual (in English)

CAUTION
When the engine coolant temperature
gauge needle is in the red range, the
engine coolant temperature is
extremely high. Drive slowly to reduce
engine load. If the engine coolant
temperature gauge needle is in the red
range, there is the possibility of
overheating. Park the vehicle in a safe
place immediately and take
appropriate measures.
Refer to Overheating on page 7-44.
NOTE
xIf the engine or engine coolant
temperature is high or low, the
engine output may be restricted to
protect the engine.
xDuring normal driving , the engine
coolant temperature stabilizes at 100
°C (210 °F) or less, and the gauge
indicates a range lower than 100 °C
(210 °F).
▼Fuel Gauge
The fuel gauge shows approximately
how much fuel is remaining in the tank
when the ignition is switched ON. We
recommend keeping the tank over 1/4
full.

1. Full
2. 1/4 Full
3. Empty

If the low fuel warning light illuminates
or the fuel level is very low, refuel as
soon as possible.
If inconsistency in engine performance
or stalling occurs due to low fuel level
conditions, refuel the vehicle as soon
as possible and add at least 10 L (2.7
US gal, 2.2 Imp gal) of fuel.
Refer to Low Fuel Warning Indication/
Warning Light on page 7-58.
NOTE
xAfter refuelling, it may require some
time for the indicator to stabilize. In
addition, the indicator may deviate
while driving on a slope or curve
since the fuel moves in the tank.
When Driving
Instrument Cluster and Display
4-26

▼Outside Temperature Display
When the ignition is switched ON, the
outside temperature is displayed.

NOTE
xUnder the following conditions, the
outside temperature display may
differ from the actual outside
temperature depending on the
surroundings and vehicle conditions:
xSignificantly cold or hot
temperatures.
xSudden changes in outside
temperature.
xThe vehicle is parked.xThe vehicle is driven at low speeds.
Changing the Temperature Unit of the
Outside Temperature Display
The outside temperature unit can be
switched between Celsius and
Fahrenheit.
Settings can be changed by operating
the centre display screen.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
NOTE
When the temperature unit indicated
in the outside temperature display is
changed, the temperature unit
indicated in the engine coolant gauge
display changes in conjunction with it.
Outside Temperature Warning*
When the outside temperature is low,
the indication flashes and a beep
sound is heard to warn the driver of
the possibility of icy roads.
If the outside temperature is lower
than about 4 °C (39 °F), the outside
temperature display and the
mark
flashes for about 3 seconds and a beep
sound is heard once.
NOTE
If the outside temperature is lower
than -20 °C (-4 °F), the beep sound
does not operate. However, the
mark illuminates.
▼Distance-to-empty
This displays the approximate distance
you can travel on the remaining fuel
based on the fuel economy.
The distance-to-empty will be
calculated and displayed every second.

NOTE
xEven though the distance-to-empty
display may indicate a
sufficient
amount of remaining driving distance
before refuelling is required, refuel as
soon as possible if the fuel level is
very low or the low fuel warning light
illuminates.
xThe display will not change unless
you add more than approximately 9
L (2.3 US gal, 1.9 Imp gal) of fuel.
When Driving
Instrument Cluster and Display
4-28*Some models.

CAUTION
If the air conditioner is used while
driving up long hills or in heavy traffic,
monitor the high engine coolant
temperature warning indication to see
if it is displayed (page 7-51).
The air conditioner may cause engine
overheating. If the warning indication
is displayed, turn the air conditioner
off (page 7-44).
NOTE
xWhen maximum cooling is desired,
set the temperature control dial to
the extreme cold position and set
the air intake selector to the
recirculated air position, then turn
the fan control dial fully clockwise.
xIf warmer air is desired at
floor level,
press the
switch and adjust the
temperature control dial to maintain
maximum comfort.
xThe air to the floor is warmer than air
to the face (except when the
temperature control dial is set at the
extreme hot or cold position).
▼Ventilation
1. Press the switch.
2. Set the air intake selector to the
outside air position (indicator light
turns off).
3. Set the temperature control dial to
the desired position.
4. Set the fan control dial to the
desired speed.
▼Windscreen Defrosting and
Defogging
1. Press the switch.
2. Set the temperature control dial to
the desired position.
3. Set the fan control dial to the
desired speed.
4. If dehumidified heating is desired,
turn on the air conditioner.
WARNING
Do not defog the windscreen using
the
switch with the temperature
control set to the cold position:
Using the
switch with the
temperature control set to the cold
position is dangerous as it will cause
the outside of the windscreen to fog
up. Your vision will be hampered,
which could lead to a serious accident.
Set the temperature control to the hot
or warm position when using the
switch.
NOTE
xFogging on the windows clears up
more easily while the air conditioner
is on, but they will fog up more easily
if the air conditioner is turned
off.
xBe careful that the windows do not
fog up when doing any of the
following:
xSwitching to recirculate modexTurning off the air conditionerxFor maximum defrosting , turn on the
air conditioner, set the temperature
control dial to the extreme hot
position, and turn the fan control
dial fully clockwise.
xIf warm air is desired at the floor,
press the
switch.
xWith the switch, the outside air
position is automatically selected to
defrost the windscreen. The air
intake selector cannot be changed to
the recirculated air position.
Interior Features
Air-Conditioning System
5-7

Maintenance item 1st2nd3rd 4th 5th 6th 7th 8th 9th10th 11th 12th
Air filter *5CCRCCRCCRCCR
Fuel filter RRRR
Fuel lines and hosesExcept Uk-
raineIIIIII
Ukraine IIIIIIIIIIII
SKYACTIV-G 2.0, SKYACTIV-X 2.0, AND SKYACTIV-D 1.8
Drive belts
*6IIII
Engine coolant level IIIIIIIIIIII
Engine coolant
*7Replace at first 200,000 km (125,000 miles) or 10 years;
after that, every 100,000 km (62,500 miles) or 5 years.
Battery
*8*9IIIIIIIIIIII
Brake lines, hoses and connections IIIIIIIIIIII
Vacuum brake booster and
hoseWith vacuum
boosterIIIIII
Brake
fluid
*10RRRRRR
Disc brakes IIIIIIIIIIII
Manual transmission oil Replace every 180,000 km (112,500 miles).
Steering operation and linkagesIIIIII
Rear differential oil
*11
Transfer oil*11
Front and rear suspension, ball joints and
wheel bearing axial playIIIIII
Driveshaft dust boots IIIIII
Exhaust system and heat shields Inspect every 100,000 km (62,500 miles) or 8 years.
Bolts and nuts on chassis and body TTTTTT
Body condition (for rust, corrosion and per-
foration)IIIIIIIIIIII
Cabin air filter (if installed) R R R R R R
Tyre inflation pressure and tyre wear
*12*13IIIIIIIIIIII
Emergency
flat tyre repair kit (if installed)
*14IIIIIIIIIIII
Self-test with Mazda Modu-
lar Diagnostic System
(M-MDS)
*15*16
SKYACTIV-G & SKYACTIV-XUkraine IIIIIIIIIIII
Maintenance and Care
Scheduled Maintenance
6-4

Chart symbols:
I: Inspect: Inspect and clean, repair, adjust, fill up, or replace if necessary.
R: Replace
C: Clean
T: Tighten
Remarks:
*1 Reset the engine oil data whenever replacing the engine oil regardless of the message/wrench
indicator light display.
*2 Except SKYACTIV-D 1.8 in Ukraine, if you drive your vehicle under any of the following conditions,
replace the engine oil &
filter every 10,000 km (6,250 miles) or shorter.
a) The vehicle is idled for long periods or driven at low speeds, such as with police cars, taxis, or
driver's education school car.
b) Driving under dusty conditions.
c) Driving for long periods in cold temperatures or driving regularly for short distances only.
d) Driving under extremely high temperature conditions.
e) Driving continuously in mountainous regions.
*3 For SKYACTIV-D 1.8 in Ukraine, if you drive your vehicle under any of the following conditions,
replace the engine oil & filter every 5,000 km (3,125 miles) or shorter.
a) The vehicle is idled for long periods or driven at low speeds, such as with police cars, taxis, or
driver's education school car.
b) Driving under dusty conditions.
c) Driving for long periods in cold temperatures or driving regularly for short distances only.
d) Driving under extremely high temperature conditions.
e) Driving continuously in mountainous regions.
*4 In the countries below, inspect the spark plugs at every 10,000 km (6,250 miles) or 12 months
before replacing them at the said interval.
Albania, Bosnia and Herzegovina, Bulgaria, Croatia, Latvia, Macedonia, Moldova, Montenegro,
Romania, Serbia, Slovakia, Ukraine
*5 If the vehicle is operated in very dusty or sandy areas, clean and if necessary, replace the air filter
more often than the recommended intervals.
*6 Also inspect the air conditioner drive belts, if installed.
If the vehicle is operated primarily under any of the following conditions, inspect the drive belts at
every 20,000 km (12,500 miles) or 12 months.
a) Driving under dusty conditions.
b) The vehicle is idled for long periods or driven at low speeds.
c) Driving for long periods in cold temperatures or driving regularly for short distances only.
d) Driving under extremely high temperature conditions.
e) Driving continuously in mountainous regions.
f) Driving for long period in extremely wet or heavy rain condition.
*7 Use of FL-22 is recommended when replacing engine coolant. Using engine coolant other than FL-22
may cause serious damage to the engine and cooling system.
*8 Inspect the battery electrolyte level, specific gravity and outer appearance. The sealed battery only
requires an outer appearance inspection.
*9 Inspection is only subjected for lead-acid battery.
Maintenance and Care
Scheduled Maintenance
6-5

*10 If the brakes are used extensively (for example, continuous hard driving or mountain driving) or if the
vehicle is operated in extremely humid climates, replace the brake fluid annually.
*11 If this component has been submerged in water, the oil should be replaced.*12 Tyre rotation is recommended every 10,000 km (6,250 miles).*13 Inspect a spare tyre if installed.*14 Check the tyre repair fluid expiration date every year when performing the periodic maintenance.
Replace the tyre repair fluid bottle with new one before the expiration date.
*15 If DTC P1200 is stored, clean the fuel system by Mazda genuine deposit cleaner.
If the required tool (M-MDS) is not available, clean the fuel system by Mazda genuine deposit
cleaner without performing self-test.
Using non-genuine deposit cleaner would cause an internal failure in the fuel system.
*16 If the vehicle is operated primarily under any of the following conditions, perform "Self-test with
Mazda Modular Diagnostic System (M-MDS)" at every 10,000 km (6,250 miles).
a) The vehicle is idled for long periods or driven at low speeds, such as with police cars, taxis, or
driver's education school car.
b) Driving under extremely high temperature conditions.
▼Except Europe
Israel
Vehicles utilizing the vehicle status monitor feature:
The vehicle status monitor feature alerts you of maintenance needs by turning on the
wrench indicator light or displaying a message in the instrument panel, or both.
Every maintenance must be done when the display/wrench indication comes on.
The display/wrench indication will come on before reaching the maximum interval.

Maximum interval 15,000 km or 12 months, whichever comes first

Manually set Next Service Distance of Vehicle Status Monitor to 10,000 km or short-
er if the vehicle is driven primarily under any of the following conditions:
Refer to the Information section in the Mazda Connect Owner's Manual about the
manual setting procedure.
1. The vehicle is idled for long periods or driven at low speeds, such as with police
cars, taxis, or driver's education school car.
2. Driving under dusty conditions.
3. Driving for long periods in cold temperatures or driving regularly for short distan-
ces only.
4. Driving under extremely high temperature conditions.
5. Driving continuously in mountainous regions.
Maintenance Item 1st2nd3rd 4th 5th 6th 7th 8th 9th10th 11th 12th
Engine oil & oil
filter *1RRRRRRRRRRRR
Drive belts
*2IIIIIIIIIIII
Engine coolant level IIIIIIIIIIII
Maintenance and Care
Scheduled Maintenance
6-6

Maintenance Item 1st2nd3rd 4th 5th 6th 7th 8th 9th10th 11th 12th
Battery *3*4IIIIIIIIIIII
Vacuum brake booster and
hoseWith vacuum
boosterIIIIIIIIIIII
Brake and clutch fluid level IIIIIIIIIIII
Brake lines, hoses and connections I I I I I I I I I I I I
Disc brakes IIIIIIIIIIII
Bolts and nuts on chassis and body T T T T T T T T T T T T
Front and rear suspension, ball joints and
wheel bearing axial playIIIIIIIIIIII
Body condition (for rust, corrosion and per-
foration)IIIIIIIIIIII
Ty re
inflation pressure and tyre wear
*5*6IIIIIIIIIIII
Emergency
flat tyre repair kit (if installed)
*7IIIIIIIIIIII
Fuel lines and hoses IIIIII
Steering operation and linkages IIIIII
Brake
fluid
*8RRRRRR
Cabin air filter (if installed) RRRRRR
Hoses and tubes for emission I I I
Driveshaft dust boots I I I I
Air filter
*9RRR
Exhaust system and heat shields I I
Manual transmission oil Replace every 100,000 km or 5 years.
Spark plugSKYACTIV-G
2.0/
SKYACTIV-G
2.5Replace every 120,000 km.
SKYACTIV-X
2.0Replace every 64,000 km.
Fuel filter Replace every 135,000 km.
Engine coolant
*10Replace at first 195,000 km or 10 years; after that, every
90,000 km or 5 years.
Chart symbols:
I: Inspect: Inspect and clean, repair, adjust, fill up, or replace if necessary.
T: Tighten
R: Replace
Maintenance and Care
Scheduled Maintenance
6-7

Remarks:
*1 Reset the engine oil data whenever replacing the engine oil regardless of the message/wrench
indicator light display.
*2 Also inspect the air conditioner drive belts, if installed.
If the vehicle is driven primarily under any of the following conditions, inspect the drive belts at every
10,000 km or shorter.
a) Driving for long period in extremely wet or heavy rain condition.
*3 Inspect the battery electrolyte level,
specific gravity and outer appearance. The sealed battery only
requires an outer appearance inspection.
*4 Inspection is only subjected for lead-acid battery.*5 Tyre rotation is recommended every 15,000 km.*6 Inspect a spare tyre if installed.*7 Check the tyre repair fluid expiration date every year when performing the periodic maintenance.
Replace the tyre repair
fluid bottle with new one before the expiration date.
*8 If the brakes are used extensively (for example, continuous hard driving or mountain driving) or if the
vehicle is driven in extremely humid climates, replace the brake fluid annually.
*9 If the vehicle is driven in very dusty or sandy areas, clean and if necessary, replace the air
filter more
often than the recommended intervals.
*10 Use of FL-22 is recommended when replacing engine coolant. Using engine coolant other than FL-22
may cause serious damage to the engine and cooling system.
Russia/Belarus/Azerbaijan/Kazakhstan/Armenia
Vehicles utilizing the vehicle status monitor feature:
Russia/Belarus/Kazakhstan
The vehicle status monitor feature alerts you of maintenance needs by turning on the
wrench indicator light or displaying a message in the instrument panel, or both.
Every maintenance must be done when the display/wrench indication comes on.
The display/wrench indication will come on before reaching the maximum interval.
Refer to Table A to identify the required maintenance items.

Maximum interval 15,000 km or 12 months, whichever comes first

Manually set Next Service Distance and Date of Vehicle Status Monitor to 7,500 km
and 6 months if the vehicle is driven primarily under any of the following conditions:
Refer to the Information section in the Mazda Connect Owner's Manual about the
manual setting procedure.
1. The vehicle is idled for long periods or driven at low speeds, such as with police
cars, taxis, or driver's education school car.
2. Driving under dusty conditions.
3. Driving for long periods in cold temperatures or driving regularly for short distan-
ces only.
4. Driving under extremely high temperature conditions.
5. Driving continuously in mountainous regions.
Maintenance and Care
Scheduled Maintenance
6-8

Refer to Table B to identify the required maintenance items.
Azerbaijan/Armenia
The vehicle status monitor feature alerts you of maintenance needs by turning on the
wrench indicator light or displaying a message in the instrument panel, or both.
Every maintenance must be done when the display/wrench indication comes on.
The display/wrench indication will come on before reaching the maximum interval.
Refer to Table B to identify the required maintenance items.

Maximum interval 5,000 km or 6 months, whichever comes
first

Manually set Next Service Distance of Vehicle Status Monitor to a shorter mileage
than 5,000 km if the vehicle is driven primarily under any of the following condi-
tions:
Refer to the Information section in the Mazda Connect Owner's Manual about the
manual setting procedure.
1. The vehicle is idled for long periods or driven at low speeds, such as with police
cars, taxis, or driver's education school car.
2. Driving under dusty conditions.
3. Driving for long periods in cold temperatures or driving regularly for short distan-
ces only.
4. Driving under extremely high temperature conditions.
5. Driving continuously in mountainous regions.
Refer to Table B to identify the required maintenance items.
Ta b l e A
Maintenance item 1st2nd3rd 4th 5th 6th 7th 8th 9th10th 11th 12th
Engine oil &
filter *1RRRRRRRRRRRR
Spark plug IIIIIIIRIIII
Drive belts
*2IIIIIIIIIIII
Engine coolant level IIIIIIIIIIII
Battery
*3*4IIIIIIIIIIII
Vacuum brake booster and
hoseWith vacuum
boosterIIIIII
Brake lines, hoses and connections I I I I I I I I I I I I
Disc brakes IIIIIIIIIIII
Steering operation and linkages I I I I I I I I I I I I
Bolts and nuts on chassis and body T T T T T T T T T T T T
Front and rear suspension, ball joints and
wheel bearing axial playIIIIIIIIIIII
Driveshaft dust boot IIIIIIIIIIII
Maintenance and Care
Scheduled Maintenance
6-9

Maintenance item 1st2nd3rd 4th 5th 6th 7th 8th 9th10th 11th 12th
Exhaust system and heat shields IIIIIIIIIIII
Function of all lights I I I I I I I I I I I I
Body condition (for rust, corrosion and per-
foration)IIIIIIIIIIII
Tyre inflation pressure and tyre wear
*5*6IIIIIIIIIIII
Emergency flat tyre repair kit (if installed)
*7IIIIIIIIIIII
Fuel lines & hoses IIIIII
Brake
fluid
*8RRRRRR
Cabin air filter (if installed) R R R R R R
Hoses and tubes for emission I I I
Air
filter
*9RRRR
Manual transmission oil R R
Fuel filterExcept below
countriesReplace every 120,000 km.
Azerbaijan/
ArmeniaReplace every 60,000 km.
Engine coolant
*10Replace at first 195,000 km or 120 months; after that,
every 90,000 km or 60 months.
Rear differential oil
*11
Transfer oil*11
Chart symbols:
I: Inspect: Inspect and clean, repair, adjust,
fill up, or replace if necessary.
T: Tighten
R: Replace
Remarks:
*1 Reset the engine oil data whenever replacing the engine oil regardless of the message/wrench
indicator light display.
*2 Also inspect the air conditioner drive belts, if installed.
If the vehicle is driven primarily under any of the following conditions, inspect the drive belts at every
7,500 km or 6 months.
a) Driving for long period in extremely wet or heavy rain condition.
*3 Inspect the battery electrolyte level, specific gravity and outer appearance. The sealed battery only
requires an outer appearance inspection.
*4 Inspection is only subjected for lead-acid battery.*5 Tyre rotation is recommended every 15,000 km.*6 Inspect a spare tyre if installed.
Maintenance and Care
Scheduled Maintenance
6-10