lights MAZDA MODEL CX-5 2017 Owners Manual (in English)
Page 574 of 664
7–32
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.
 Signal  Warning   Action  to  be  taken 
  
 
  (Amber)
  Smart  Brake  Support/ Smart City Brake 
Support (SBS/SCBS)  Warning Indication/ Warning Light 
*    The light turns on if the windshield or 
the radar sensor are dirty, or there is a 
malfunction in the system.   Verify the reason why the warning light is 
illuminated on the center display.
  If the reason why the warning light is 
illuminated is due to a dirty windshield, 
clean the windshield.
  If the warning light is illuminated because 
of a dirty radar sensor, clean the front 
emblem.
  For any other reasons, have the vehicle 
inspected at an Authorized Mazda Dealer. 
 
 
 Low  Fuel  Warning 
Indication/Warning Light   
The light turns on when the remaining fuel 
is about 9.0 L (2.3 US gal, 1.9 Imp gal).
   NOTE
  The light illumination timing may 
vary because fuel inside the fuel tank 
moves around according to the driving 
conditions and the vehicle posture.    
 Add  fuel. 
  
 
  Check  Fuel  Cap  Warning 
Indication/Warning Light   If the check fuel cap warning light 
illuminates while driving, the fuel-
fi ller 
cap may not be installed properly.   Stop the engine and reinstall the fuel-
fi ller 
cap.
  Refer to Fuel-Filler Cap on page  3-34  
CX-5_8FN1-EA-16L_Edition1.indb   322016/12/12   10:07:27 
Page 575 of 664
7–33
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
 Signal  Warning   Action  to  be  taken 
  
 
  Seat  Belt  Warning  Light 
   Except  Mexico  
  The seat belt warning light turns on if the driver 
or front passenger's seat is occupied and the seat 
belt is not fastened with the ignition switched 
ON.
  If the driver or front passenger's seat belt is 
unfastened (only when the front passenger's seat 
is occupied) and the vehicle is driven at a speed 
faster than about 20 km/h (12 mph), the warning 
light fl  ashes. After a short time, the warning 
light stops fl  ashing, but remains illuminated.
   NOTE
     
   The  warning  light  fl ashes for about 6 seconds 
if the driver's seat belt is not fastened when the 
ignition is switched ON.  
      To allow the front passenger occupant 
classifi  cation sensor to function properly, do 
not place and sit on an additional seat cushion 
on the front passenger's seat. The sensor may 
not function properly because the additional 
seat cushion could cause sensor interference.  
      If a small child is seated on the front 
passenger's seat, the warning light may not 
operate.     
    Mexico  
  The seat belt warning light turns on if the driver 
or front passenger's seat is occupied and the seat 
belt is not fastened with the ignition switched 
ON.
  If the driver or front passenger's seat belt is 
unfastened (only when the front passenger's seat 
is occupied) and the vehicle is driven at a speed 
faster than about 20 km/h (12 mph), the warning 
light  fl ashes. After a short time, the warning 
light stops fl  ashing, but remains illuminated. If 
a seat belt remains unfastened, the warning light 
fl  ashes again for a given period of time.
   NOTE
     
   Placing heavy items on the front passenger's 
seat may cause the front passenger's seat belt 
warning function to operate depending on the 
weight of the item.  
      To allow the front passenger seat weight sensor 
to function properly, do not place and sit on an 
additional seat cushion on the front passenger's 
seat. The sensor may not function properly 
because the additional seat cushion could 
cause sensor interference.  
      If a small child is seated on the front 
passenger's seat, the warning light may not 
operate.      
 Fasten the seat belts. 
CX-5_8FN1-EA-16L_Edition1.indb   332016/12/12   10:07:27 
Page 576 of 664
7–34
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.
 Signal  Warning   Action  to  be  taken 
  
 
  Low  Washer  Fluid  Level  Warning Indication/Warning Light 
*    This warning light indicates that little 
washer fl
 uid remains.   Add  washer 
fl  uid  (page   6-27 ). 
 
  Door-Ajar/Liftgate-Ajar  Warning Indication/ Warning Light   The light turns on if any door/liftgate is 
not closed securely. 
 Close the door/liftgate securely. 
   
  
  KEY  Warning  Indication/Warning  Light 
* 
    Take the appropriate action and verify that the warning light turns off.
  
 Signal   Cause   Action  to  be  taken 
  
 
  (White)
  KEY  Warning  Indication   The key battery is dead. 
 Replace the key battery (page  6-36 ). 
  
 
  (Red)
  (Flashing)
  KEY  Warning  Light   The key battery is dead. 
 Replace the key battery (page  6-36 ). 
 The key is not within the operation range.   Bring the key into the operation range 
(page   3-8 ). 
 The key is placed in areas inside the 
cabin where it is dif
fi cult for the key to be 
detected. 
 A key from another manufacturer similar to 
the key is in the operation range.   Take the key from another manufacturer 
similar to the key out of the operation 
range. 
 Without the ignition switched off, the key is 
taken out of the cabin, and then all the doors 
are closed.   Bring the key back into the cabin. 
   
CX-5_8FN1-EA-16L_Edition1.indb   342016/12/12   10:07:27 
Page 577 of 664
7–35
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.
 Message Indicated in Multi-information Display * 
            If  there  is  a  notifi cation from the vehicle, a message is displayed in the multi-information\
 
display. Check the information and take the necessary action.
  
 
(Display example)
 
  If the warning light turns on/ fl ashes simultaneously or a symbol is indicated in the display, 
check the information regarding the warning light or symbol. (page   4-32 )
  
 Display   Content   Action  to  be  taken 
 
   Indicated when the push button start is 
pressed while the shift lever is not in the 
P position. 
 Shift the shift lever to the P position. 
 
   Indicated when the push button start is 
pressed without depressing the brake 
pedal. 
 Depress the brake pedal and press the 
push button start. 
 
   Indicated while the steering wheel is 
locked. 
 Release the steering lock. 
 
   Indicates when the Electric Parking 
Brake (EPB) switch is operated without 
depressing the brake pedal. 
 Operate the Electric Parking Brake 
(EPB) switch while depressing the brake 
pedal. 
CX-5_8FN1-EA-16L_Edition1.indb   352016/12/12   10:07:27 
Page 578 of 664
7–36
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
 Display  Content   Action  to  be  taken 
 
   Indicates when there is a problem with 
the brake related system while the 
vehicle is being held in a stop position 
by the AUTOHOLD function or during 
the Mazda Radar Cruise Control with 
Stop & Go function (MRCC with Stop & 
Go function) stop hold control.   Depress the brake pedal.
  Cancel the AUTOHOLD function or 
the Mazda Radar Cruise Control with 
Stop & Go function (MRCC with Stop 
& Go function), and have your vehicle 
inspected at an Authorized Mazda 
Dealer. 
 
   Indicates the possibility of the vehicle 
not being held in the stopped position by 
the AUTOHOLD function, such as on 
steep slopes. 
 Depress and hold your foot on the brake 
pedal. 
 
   Indicates when the cancel operation is 
done without depressing the brake pedal 
while the vehicle is being held in the 
stopped position by the AUTOHOLD 
function or during the stop hold control 
of the Mazda Radar Cruise Control with 
Stop & Go function (MRCC with Stop & 
Go function). 
 Cancel the AUTOHOLD function or 
the Mazda Radar Cruise Control with 
Stop & Go function (MRCC with Stop 
& Go function) stop hold control while 
depressing the brake pedal. 
   
CX-5_8FN1-EA-16L_Edition1.indb   362016/12/12   10:07:28 
Page 579 of 664
7–37
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.
 Message Indicated on Display * 
            If a message is displayed in the center display (Type B audio), take appropriate action (in a 
calm manner) according to the displayed message.
   
(Display example)
 
         Stop Vehicle in Safe Place Immediately
    If the following messages are displayed in the center display , a vehicl\
e system may be 
malfunctioning. Stop the vehicle in a safe place and contact an Authorized Mazda Dealer.
  
 Display   Indicated  Condition 
 
   Displays if the engine coolant temperature has increased 
excessively. 
 
   Displays if the charging system has a malfunction. 
   
CX-5_8FN1-EA-16L_Edition1.indb   372016/12/12   10:07:28 
Page 580 of 664
7–38
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
          Verify Display Content
    Displays  in  the  following  cases:
  
 Display  Indicated Condition/Action to be taken 
 
   The following message is displayed when the 
temperature around the center display is high.
  Lowering the temperature in the cabin or the 
temperature around the center display by avoiding 
direct sunlight is recommended. 
   
CX-5_8FN1-EA-16L_Edition1.indb   382016/12/12   10:07:29 
Page 581 of 664
7–39
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
 Warning Sound is 
Activated
                   Lights-On  Reminder
              The  lights-on  reminder  is  operable  when 
the time setting *1  of the auto headlight off 
function is off.
  If lights are on and the ignition is switched 
to ACC or off, a continuous beep sound 
will be heard when the driver's door is 
opened.
  
   *1  If the light switch is left on, the auto  headlight off function automatically 
turns off the lights about 30 seconds 
after switching the ignition off. The 
time setting can be changed.
    Refer to Personalization Features on  page   9-11 .
    
   NOTE
   When the ignition is switched to ACC, 
the “Ignition Not Switched Off (STOP) 
Warning Beep” (page  7-40 ) overrides 
the lights-on reminder. 
   A personalized function is available to 
change the sound volume for the lights-
on reminder.
  Refer to Personalization Features on  page   9-11 .
     
          Air Bag/Seat Belt Pretensioner System Warning Beep
              If  there  is  a  problem  with  the  air  bag/seat 
belt pretensioner systems and the warning 
light illumination, a warning beep sound 
will be heard for about 5 seconds every 
minute.
  
  The air bag and seat belt pretensioner 
system warning beep sound will continue 
to be heard for approximately 
35 minutes. Have your vehicle inspected 
at an Authorized Mazda Dealer as soon as 
possible.
  WARNING 
  Do not drive the vehicle with the air 
bag/seat belt pretensioner system 
warning beep sounding:
  Driving the vehicle with the air bag/
seat belt pretensioner system warning 
beep sounding is dangerous. In a 
collision, the air bags and the seat belt 
pretensioner system will not deploy 
and this could result in death or serious 
injury. Contact an Authorized Mazda 
Dealer to have the vehicle inspected as 
soon as possible.
   
CX-5_8FN1-EA-16L_Edition1.indb   392016/12/12   10:07:29 
Page 582 of 664
7–40
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
          Seat Belt Warning Beep
              Except  Mexico
    If the driver's seat belt is not fastened 
when the ignition is switched ON, a beep 
sound will be heard for about 6 seconds. If 
the driver or the front passenger's seat belt 
is not fastened and the vehicle is driven at 
a speed faster than about 20 km/h 
(12 mph), a beep sound will be heard 
again for a specifi ed period of time.
  Until a seat belt is fastened or a given 
period of time has elapsed, the beep sound 
will not stop even if the vehicle speed falls 
below 20 km/h (12 mph).
   NOTE
    To allow the front passenger occupant 
classifi  cation sensor to function 
properly, do not place and sit on an 
additional seat cushion on the front 
passenger's seat. The sensor may not 
function properly because the additional 
seat cushion could cause sensor 
interference.
    If a small child is seated on the front 
passenger's seat, the warning beep may 
not operate.
     
  Mexico
    If the vehicle speed exceeds about 
20 km/h (12 mph) with the driver or front 
passenger's seat belt unfastened, a warning 
beep sounds continuously. If the seat belt 
remains unfastened, the beep sound stops 
once and then continues for about 
90 seconds. The beep stops after the driver 
or front passenger's seat belt is fastened.
  Until a seat belt is fastened or a given 
period of time has elapsed, the beep sound 
will not stop even if the vehicle speed falls 
below 20 km/h (12 mph).
   NOTE
   Placing heavy items on the front 
passenger's seat may cause the front 
passenger's seat belt warning function 
to operate depending on the weight of 
the item.
   To allow the front passenger seat weight 
sensor to function properly, do not place 
and sit on an additional seat cushion on 
the front passenger's seat. The sensor 
may not function properly because the 
additional seat cushion could cause 
sensor interference.
   If a small child is seated on the front 
passenger's seat, the warning beep may 
not operate.
     
          Ignition Not Switched Off (STOP) Warning Beep
              If  the  driver's  door  is  opened  with  the 
ignition switched to ACC, a beep will 
be heard continuously in the cabin to 
notify the driver that the ignition has not 
been switched OFF (STOP). Under this 
condition, the keyless entry system will 
not operate, the vehicle cannot be locked, 
and the battery voltage will be depleted.
CX-5_8FN1-EA-16L_Edition1.indb   402016/12/12   10:07:29 
Page 583 of 664
7–41
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.
          Key Removed from Vehicle Warning Beep
                  Vehicles  with  advanced  keyless  function
    If the key is taken out of the vehicle while 
the ignition is not switched OFF and 
all the doors are closed, the beep which 
sounds outside of the vehicle will be heard 
6 times, the beep which sounds inside 
the vehicle will be heard 6 times, and the 
KEY warning light (red) in the instrument 
cluster fl  ashes continuously to notify 
the driver that the ignition has not been 
switched OFF.
  Vehicles without advanced keyless 
function
    If the key is taken out of the vehicle while 
the ignition is not switched OFF and all 
the doors are closed, a beep will be heard 
in the cabin 6 times and the KEY warning 
light (red) in the instrument cluster turns 
on continuously to notify the driver that 
the ignition has not been switched OFF.
   NOTE
  Because the key utilizes low-intensity 
radio waves, the Key Removed From 
Vehicle Warning may activate if the key is 
carried together with a metal object or it 
is placed in a poor signal reception area.
   
          Request Switch Inoperable  Warning Beep (With the advanced 
keyless function)
              If  the  request  switch  is  pressed  with  the 
door open or ajar, or the ignition is not 
switched OFF with a key being carried, a 
beep will be heard outside for about 
2 seconds to notify the driver that the door 
or liftgate cannot be locked.
          Key Left-in-luggage Compartment Warning Beep (With the advanced 
keyless function)
              If  the  key  is  left  in  the  luggage 
compartment with all the doors locked and 
the liftgate closed, a beep will be heard 
outside for about 10 seconds to notify 
the driver that the key is in the luggage 
compartment. In this case, take out the 
key by pressing the electric liftgate opener 
and opening the liftgate. The key taken 
out of the luggage compartment may 
not operate because its functions have 
been temporarily stopped. To restore the 
key's functions, perform the applicable 
procedure  (page   3-9 ).
          Key Left-in-vehicle Warning Beep (With the advanced keyless 
function)
              If  all  the  doors  and  luggage  compartment 
are locked using another key while the key 
is left in the cabin, the beep which sounds 
outside of the vehicle will be heard for 
about 10 seconds to notify the driver that 
the key is in the cabin. In this case, take 
out the key by opening the door. A key 
taken out of the vehicle using this method 
may not operate because its functions have 
been temporarily stopped. To restore the 
key's functions, perform the applicable 
procedure  (page   3-9 ).
          Electronic Steering Lock Warning Beep * 
              The  warning  beep  operates  if  the  steering 
wheel is not unlocked after the push button 
start is pressed. (page  4-4 )
CX-5_8FN1-EA-16L_Edition1.indb   412016/12/12   10:07:29