brakes MAZDA MODEL CX-5 2017 (in English) Owner's Manual

4–122
When Driving
i-ACTIVSENSE
Do not use the Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop &
Go function) system in the following locations, using the Mazda Radar Cruise Control
with Stop & Go function (MRCC with Stop & Go function) system at the following
locations may result in an unexpected accident:
 General roads other than highways (Driving under these conditions using the Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go function) system
is not possible.)
 Roads with sharp curves and where vehicle traffi c is heavy and there is insuffi cient
space between vehicles.
 Roads where frequent and repetitive acceleration and deceleration occur (Driving under these conditions using the Mazda Radar Cruise Control with Stop & Go function
(MRCC with Stop & Go function) system is not possible).
 When entering and exiting interchanges, service areas, and parking areas of highways (If you exit a highway while headway control is in use, the vehicle ahead will no longer
be tracked and your vehicle may accelerate to the set speed).
 Slippery roads such as ice or snow-bound roads (Tires could spin causing you to lose vehicle control, or the stop hold control may not operate.)
 Long, descending slopes (to maintain distance between vehicles, the system automatically and continuously applies the brakes which could result in the loss of
brake power.)
 Slopes with a steep gradient (The vehicle ahead may not be detected correctly, your vehicle may slide while stopped by the stop hold control, and it may accelerate
suddenly after it starts moving.)

For safety purposes, switch the Mazda Radar Cruise Control with Stop & Go function
(MRCC with Stop & Go function) system off when it is not being used.
Do not get out of the vehicle while the stop hold control is operating: Getting out of the vehicle while the stop hold control is operating is dangerous as the
vehicle may move unexpectedly and result in an accident. Before getting out of the
vehicle, switch the Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop
& Go function) system off , shift the selector lever to the P position, and apply the electric
parking brake (EPB).

CAUTION
If your vehicle is towed or you are towing something, switch the Mazda Radar Cruise
Control with Stop & Go function (MRCC with Stop & Go function) system off to prevent a
miss-operation.

CX-5_8FN1-EA-16L_Edition1.indb 1222016/12/12 10:06:09

4–123
When Driving
i-ACTIVSENSE
NOTE
  The Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go
function) system does not detect the following as physical objects.
  Vehicles approaching in the opposite direction  Pedestrians  Stationary objects (stopped vehicles, obstructions)  If a vehicle ahead is traveling at an extremely low speed, the system may not detect it
correctly.
  During headway control travel, do not set the system for detection of two-wheeled
vehicles such as motorcycles and bicycles.
  Do not use the Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop
& Go function) system under conditions in which close proximity warnings are frequently
activated.
  During headway control travel, the system accelerates and decelerates your vehicle in
conjunction with the speed of the vehicle ahead. However, if it is necessary to accelerate
for a lane change or if the vehicle ahead brakes suddenly causing you to\
close in on the
vehicle rapidly, accelerate using the accelerator pedal or decelerate using the brake
pedal depending on the conditions.
  While the Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go
function) system is in use, it does not cancel even if the selector lev\
er is operated and any
intended engine braking does not occur. If deceleration is required, lower the set speed or
depress the brake pedal.
  The sound of the automatic brakes operating may be heard, however, it does not indicate
a problem.
  The brake lights turn on while the Mazda Radar Cruise Control with Stop & Go function
(MRCC with Stop & Go function) automatic braking is operating, however\
.

CX-5_8FN1-EA-16L_Edition1.indb 1232016/12/12 10:06:10

4–125
When Driving
i-ACTIVSENSE
If there is a problem with the Mazda Radar Cruise Control with Stop & Go\
function (MRCC
with Stop & Go function) system, a message is displayed on the multi-in\
formation display.
Check the center display to verify the problem and then have your vehicl\
e inspected by an
Authorized Mazda Dealer.
Refer to Message Indicated on Display on page 7-37 .
Close Proximity Warning
If your vehicle rapidly closes in on the vehicle ahead because the vehic\
le ahead applies
the brakes suddenly while you are traveling in headway control, the warn\
ing sound
activates and the brake warning is indicated in the display. Always verify the safety of
the surrounding area and depress the brake pedal while keeping a safer d\
istance from the
vehicle ahead. Additionally, keep a safer distance from the vehicles behind you.

Multi-information Display
Active Driving Display

NOTE
In the following cases, the warnings and brakes may not operate even if \
your vehicle starts
closing in on the vehicle ahead.
  You are driving your vehicle at the same speed as the vehicle ahead.  Directly after the Mazda Radar Cruise Control with Stop & Go function (MRCC with
Stop & Go function) system has been set.
  Directly after the accelerator pedal is released.  Another vehicle cuts into the driving lane.
CX-5_8FN1-EA-16L_Edition1.indb 1252016/12/12 10:06:10

4–14 8
When Driving
i-ACTIVSENSE
*Some models.
Smart City Brake Support (SCBS) *
The Smart City Brake Support (SCBS) system alerts the driver of a possible collision using
an indication in the display and a warning sound when the Forward Sensin\
g Camera (FSC)
detects a vehicle ahead and determines that a collision with a vehicle a\
head is unavoidable
while the vehicle is being driven at a vehicle speed of about 4 to 80 km\
/h (2 to 50 mph).
In addition, the system reduces damage in the event of a collision by op\
erating the brake
control (Smart City Brake Support (SCBS) brake) when the system dete\
rmines that a
collision is unavoidable while the vehicle is being driven at a vehicle \
speed of about 4 to
30 km/h (2 to 18 mph). It may also be possible to avoid a collision if\
the relative speed
between your vehicle and the vehicle in front of you is less than about \
20 km/h (12 mph).
In addition, when the driver depresses the brake pedal while the system \
is in the operation
range at about 4 to 30 km/h (2 to 18 mph), the brakes are applied fi rmly and quickly to
assist. (Brake Assist (Smart City Brake Support (SCBS) brake assist))


Forward Sensing
Camera (FSC)

CX-5_8FN1-EA-16L_Edition1.indb 1482016/12/12 10:06:16

4–150
When Driving
i-ACTIVSENSE
NOTE
  The Smart City Brake Support (SCBS) system will operate under the foll\
owing conditions.   The engine is running.  The Smart Brake Support/Smart City Brake Support (SBS/SCBS) system war\
ning
indication/warning light (amber) does not illuminate.
  (Rear-end collision warning)  The vehicle speed is about 4 to 80 km/h (2 to 50 mph).  (Brake control (Smart City Brake Support (SCBS) brake))  The vehicle speed is about 4 to 30 km/h (2 to 18 mph).  The Smart City Brake Support (SCBS) system is not turned off.   Under the following conditions, the Smart City Brake Support (SCBS) sy\
stem may not
operate normally:
  The Smart City Brake Support (SCBS) system will not operate if the dri\
ver is
deliberately performing driving operations (accelerator pedal and steer\
ing wheel).
  If there is the possibility of partial contact with a vehicle ahead.  The vehicle is driven on a slippery road surface such as wet roads or icy or snow-
bound roads.
  The braking performance is adversely affected due to cold temperatures or wet brakes.  The vehicle is driven at the same speed as the vehicle ahead.  The accelerator pedal is depressed.  The brake pedal is depressed.  The steering wheel is being operated.  The selector lever is being operated.   In the following cases, the Forward Sensing Camera (FSC) determines that there is a
vehicle ahead and the Smart City Brake Support (SCBS) may operate.
  Objects on the road at the entrance to a curve.  Vehicles passing in the opposite lane while making a curve.  Metal objects, bumps, or protruding objects on the road.  When passing through a toll gate.  When passing through low gates, narrow gates, car washing machines, or tunnels.  If you suddenly come close to a vehicle ahead.  2-wheeled vehicles, pedestrians, animals or standing trees.  Vehicle is driven with some of the tires having signi fi cant wear.

CX-5_8FN1-EA-16L_Edition1.indb 1502016/12/12 10:06:16

4–151
When Driving
i-ACTIVSENSE
Smart City Brake Support (SCBS) Indicator Light (Red)
If the Smart City Brake Support (SCBS) is
operating, the indicator light (red) fl ashes.



Collision Warning
If there is the possibility of a collision
with a vehicle ahead, the beep sounds
continuously and a warning is indicated in
the multi-information display or the active
driving display.

Multi-information Display
Active Driving Display

NOTE
The operation distance and volume of the
collision warning can be changed. Refer to
Personalization Features on page 9-11 .

Automatic Brake Operation
Display
“Smart City Brake Support Activated” is
indicated in the multi-information display
after the SCBS brakes or the brake assist
(SCBS brake assist) is operated.


NOTE
  The collision warning beep sounds
intermittently while the SCBS brake
or brake assist (SCBS brake assist) is
operating.
  If the vehicle is stopped by the SCBS
operation and the brake pedal is not
depressed, the warning beep sounds
one time after about 2 seconds and the
SCBS brake is automatically released.

CX-5_8FN1-EA-16L_Edition1.indb 1512016/12/12 10:06:16

4–153
When Driving
i-ACTIVSENSE
*Some models.
Smart Brake Support (SBS) *
The Smart Brake Support (SBS) system alerts the driver of a possible collision using a
display and warning sound if the radar sensor (front) and the Forward \
Sensing Camera
(FSC) determine that there is the possibility of a collision with a ve\
hicle ahead while the
vehicle is being driven at about 15 km/h or faster (10 mph or faster).\
Furthermore, if the
radar sensor (front) and the Forward Sensing Camera (FSC) determines\
that a collision is
unavoidable, the automatic brake control is performed to reduce damage i\
n the event of a
collision.
In addition, when the driver depresses the brake pedal, the brakes are a\
pplied fi rmly and
quickly to assist. (Brake Assist (SBS brake assist))
WARNING
Do not rely completely on the Smart Br ake Support (SBS) system and always drive
carefully: The Smart Brake Support (SBS) is designed to reduce damage in the event of a collision,
not avoid an accident. The ability to detect an obstruction is limited depending on the
obstruction, weather conditions, or traffi c conditions. Therefore, if the accelerator pedal
or brake pedal is mistakenly operated it could result in an accident. Always verify the
safety of the surrounding area and depress the brake pedal or accelerator pedal while
keeping a safer distance from vehicles ahead or on-coming vehicles.

CAUTION
In the following cases, turn the system off to prevent a mis-operation:  The vehicle is being towed or when towing another vehicle. The vehicle is on a chassis roller. When driving on rough roads such as in areas of dense grass or off -road.
CX-5_8FN1-EA-16L_Edition1.indb 1532016/12/12 10:06:16

6–4
Maintenance and Care
Scheduled Maintenance
Scheduled Maintenance (U.S.A., Canada, and Puerto Rico)
Follow Schedule 1 if the vehicle is operated mainly where none of the fo\
llowing conditions
(severe driving conditions)apply.
  Repeated short-distance driving  Driving in dusty conditions  Driving with extended use of brakes  Driving in areas where salt or other corrosive materials are used  Driving on rough or muddy roads  Extended periods of idling or low-speed operation  Driving for long periods in cold temperatures or extremely humid climate\
s  Driving in extremely hot conditions  Driving in mountainous conditions continually
If any do apply, follow Schedule 2. (Canada residents follow Schedule 2.)
Vehicles using Engine Oil Flexible Maintenance
Engine Oil Flexible Maintenance is selected by default for U.S.A. and Pu\
erto Rico residents.
If any following conditions do apply, follow Schedule 2 with engine oil fi xed maintenance.
   Extended periods of idling or low-speed operation such as police car, taxi or driving
school car
   Driving in dusty conditions
The vehicle calculates the remaining oil life based on engine operating \
conditions. The
vehicle lets you know when an oil change is due by illuminating the wren\
ch indicator light
in the instrument cluster. Change the oil as soon as possible within the next 1000 km
(600 mile) or 15 days. Refer page 6-16 for the details.
NOTE
  Please ensure that the Flexible Oil Maintenance Setting is reset after each Oil and Filter
replacement.
  For maintenance guidelines beyond the miles/months listed, follow the ma\
intenance
intervals provided in the Scheduled Maintenance Tables.

CX-5_8FN1-EA-16L_Edition1.indb 42016/12/12 10:07:05

6–5
Maintenance and Care
Scheduled Maintenance
Schedule 1
U.S.A. and Puerto Rico residents - Engine oil fl exible maintenance interval
Use when the maintenance monitor for “Oil Change” is set to “Flexible”. For details,
see maintenance monitor. (page 6-16 )
Maintenance Interval Number of months or kilometers (miles), whichever comes
fi rst.
Months 12 24 36 48 60 72 84 96
×1000 km 12 24 36 48 60 72 84 96
×1000 miles 7.5 15 22.5 30 37.5 45 52.5 60
Spark plugs Replace every 120,000 km (75,000 miles).
Air fi lter Replace when any equivalent timing of replacing engine oil.
(Max interval: 36 months or 60,000 km (37,500 miles))
Drive belts I I
Engine oil & fi lter
*1 Replace when wrench indicator light is ON. (Max interval:
12 months or 12,000 km (7,500 miles))
Engine coolant
*2 Replace at
fi rst 192,000 km (120,000 miles) or 10 years;
after that, every 96,000 km (60,000 miles) or 5 years.
Fuel lines and hoses
*3 I I I I
Hoses and tubes for emission
*3 I I
Brake lines, hoses and connections I I I I
Disc brakes I I I I I I I I
Tire (Rotation) Rotate when any equivalent timing of replacing engine oil.
(Max interval: 12,000 km (7,500 miles))
Steering operation and linkages I I I I
Front and rear suspension, ball joints and wheel
bearing axial play I
I I I
Rear differential oil
*4
Transfer oil *4
Driveshaft dust boots I I I I
Bolts and nuts on chassis and body T T T T
Exhaust system and heat shields I
Emergency fl at tire repair kit (if installed)
*5 Inspect annually.
Cabin air fi lter Replace when any equivalent timing of replacing engine oil.
(Max interval: 24 months or 48,000 km (30,000 miles))
Chart symbols:
I: Inspect: Inspect and clean, repair, adjust, fi ll up, or replace if necessary.
C: Clean
T: Tighten
CX-5_8FN1-EA-16L_Edition1.indb 52016/12/12 10:07:05

6–6
Maintenance and Care
Scheduled Maintenance
Remarks:
*1 The engine oil and fi lter must be changed at least once a year or within 12,000 km (7,500 mi\
les) since last
engine oil and fi lter change. Reset the engine oil data whenever replacing the engine oil\
regardless of the
message/wrench indicator light display.
*2 Use of FL-22 is recommended when replacing engine coolant. Using engine \
coolant other than FL-22 may cause serious damage to the engine and cooling system.
*3 According to state/provincial and federal regulations, failure to perfor\
m maintenance on these items will not void your emissions warranties. However, Mazda recommends that all maintenance services be performed at the
recommended time or mileage/kilometer period to ensure long-term reliabi\
lity.
*4 If this component has been submerged in water, the oil should be replaced.
*5 Check the tire repair fl uid expiration date every year when performing the periodic maintenance.\
Replace the
tire repair fl uid bottle with new one before the expiration date.


Schedule 2
U.S.A. and Puerto Rico residents - Severe driving conditions maintenance interval
Maintenance Interval Number of months or kilometers (miles), whichever comes
fi rst.
Months 6 12 18 24 30 36 42 48 54 60 66 72
×1000 km 8 16 24 32 40 48 56 64 72 80 88 96
×1000 miles 5 10 15 20 25 30 35 40 45 50 55 60
Spark plugs Replace every 120,000 km (75,000 miles).
Air fi lter
*1 Replace when any equivalent timing of replacing engine oil.
(Max interval: 36 months or 60,000 km (37,500 miles))
Drive belts I I
Engine oil & fi lter Flexible
*2
Replace when wrench indicator light is ON. (Max interval: 12
months or 12,000 km (7,500 miles))
Fixed R R R R R R R R R R R R
Engine coolant
*3 Replace at
fi rst 192,000 km (120,000 miles) or 10 years;
after that, every 96,000 km (60,000 miles) or 5 years.
Engine coolant level I I I I I I I I I I I I
Fuel lines and hoses
*4 I I I
Hoses and tubes for emission
*4 I
Function of all lights I I I I I I I I I I I I
Brake lines, hoses and connections I I I
Brake and clutch fl uid level I I I I I I I I I I I I
Disc brakes I I I I I I
Tire (Rotation) Rotate when any equivalent timing of replacing engine oil.
(Max interval: 8,000 km (5,000 miles))
Tire in fl ation pressure and tire wear I I I I I I I I I I I I
Steering operation and linkages I I I
Front and rear suspension, ball joints and wheel
bearing axial play I
I I
Rear differential oil
*5
CX-5_8FN1-EA-16L_Edition1.indb 62016/12/12 10:07:05