display MAZDA MODEL CX-5 SKYACTIV-D 2019 Owners Manual

Interior Equipment (View B)
ƒDashboard illumination knob............................ ................................. page 4-19, 4-35, 4-50
„ Active driving display........................................................................................... page 4-58
… Instrument cluster........................................ .......................................................... page 4-12
† Heated steering wheel switch................................................................................ page 2-24
‡ Seat warmer switches............................................................................................ page 2-22
ˆ Hazard warning flasher switch............................. ................................................. page 4-86
‰ Audio..................................................................................................................... page 5-19
Š Rear window defogger switch............................................................................... page 4-84
‹ Glove compartment.............................................................................................page 5-104
ΠClimate control system............................................................................................page 5-4
Seat ventilation switches....................................................................................... page 2-23
Ž Accessory socket................................................................................................... page 5-99
Push button start...................................................................................................... page 4-4
Horn.......................................................................................................................page 4-86
‘ Lock release lever................................................................................................... page 2-5
’ Hood release handle.............................................................................................. page 6-21
“ Remote fuel-filler lid release................................................................................. page 3-33
Pictorial Index
Interior Overview
The equipment and installation position varies by vehicle1-3
CX-5_8HH4-EA-19A_Edition1 2018-11-21 10:03:20

Refer to Height Adjustment on page 2-20.
â–¼Driving Position Memory*
The desired driving position can be called
up after programming the position.
The following driving positions can be
programmed.
ï‚·Driver’s seat position (seat slide, height
adjustment, front edge of seat bottom,
seat recline)
Refer to Adjusting the Driver's Seat on
page 2-5.
ï‚·Active driving display (display position,
brightness level, display information)
Refer to Active Driving Display on page
4-58.
CAUTION
Do not place fingers or hands around the
bottom of the seat while the seat memory
function is operatin
g. The seat moves
automatically while the seat memory
function is operating and fingers or hands
could get pinched and injured.
SET button
1
2
A driving position can be programmed or
operated using the buttons on the side of
the seat or the key.
NOTE
ï‚·Lumbar support adjustment cannot be
programmed.
ï‚·A driving position can be programmed
to the buttons on the side of the seat and
the key in use for driving the vehicle.
ï‚·If the vehicle has been serviced and the
battery cables disconnected, the
programmed seat positions will have
been erased. Re-program the seat
positions.
Programming
1. Make sure the parking brake is on.
2. Make sure the selector lever is in the P position.
3. Start the engine.
4. Adjust the seat and the active driving
display to the desired driving position.
5. Press the SET button on the seat until a
beep sound is heard 1 time.
6. Perform one of the following settings
within 5 seconds of completing step 5
above:
ï‚·Programming using a button on
the side of the seat
Press the button you want to
program, either button 1 or 2, until a
beep sound is heard 1 time.
ï‚·Programming using the key
Press the key
button until a beep
sound is heard 1 time.
NOTE
If a beep sound is heard 3 times, the
operation is canceled.
Essential Safety Equipment
Seats
*Some models.2-11
CX-5_8HH4-EA-19A_Edition1 2018-11-21 10:03:20

To move the driving position to a
programmed position
(Using a button on the side of the seat)
1. Make sure the parking brake is on.
2. Make sure the selector lever is in the Pposition.
3. Start the engine.
4. Press the programming button for the
driving position you want to call up
(button 1 or 2).
5. A beep sound is heard when the driving position adjustment is
completed.
NOTE
ï‚·If the driving position movement is not
changed, only the beep sounds.
ï‚·A seat position can be called up even
with the engine not running.
ï‚·The driving position adjustment is
canceled in the following cases:
ï‚·Any of the seat adjustment switches is
operated.
ï‚·The SET button is pressed.
ï‚·Programming button 1 or 2 is pressed.
ï‚·The key button or button is
operated.
ï‚·The vehicle starts moving.
ï‚·The active driving display is adjusted.
(Using a programmed key)
1. Unlock the doors by pressing a request switch or the key
button.
2. After unlocking the doors, the seatposition adjustment begins within 40
seconds of opening the driver's door,
and a beep sounds when the operation
is finished.
3. Make sure the parking brake is on.
4. Make sure the selector lever is in the P position.
5. Start the engine.
6. The active driving display adjustment begins.
NOTE
ï‚·If there is no driving position movement,
a beep is not heard.
ï‚·The driving position adjustment is
canceled in the following cases:
ï‚·Any of the seat adjustment switches is
operated.
ï‚·The SET button is pressed.
ï‚·Programming button 1 or 2 is pressed.
ï‚·The key button or button is
operated.
ï‚·The vehicle starts moving.
ï‚·The active driving display is adjusted.
Erasing programmed driving positions
(Erasing the driving positions
programmed to the key)
1. Switch the ignition OFF.
2. Press the SET button on the side of the seat until a beep sound is heard 1 time.
3. After the beep sounds, press the key
button within 5 seconds until a beep
sound is heard 1 time.
NOTE
If a beep sound is heard 3 times, the
operation is canceled.
Essential Safety Equipment
Seats
2-12
CX-5_8HH4-EA-19A_Edition1 2018-11-21 10:03:20

ï‚·This highly-visible label is displayed which warns against the use of a rear-facing
child-restraint system on the front passenger seat.

(Except Mexico) (Mexico)
Essential Safety Equipment
SRS Air Bags
2-62
CX-5_8HH4-EA-19A_Edition1 2018-11-21 10:03:20

NOTE
The driver must carry the key to ensure the
system functions properly.
Auxiliary key
Transmitter
Key code number plate
To use the auxiliary key, pull out the
auxiliary key from the transmitter while
pressing the knob.
Knob
Keyless Entry System
This system uses the key buttons to
remotely lock and unlock the doors and
the liftgate, and opens/closes the liftgate.
The system can start the engine without
having to take the key out of your purse or
pocket.
It can also help you signal for attention or
help.
Operating the theft-deterrent system is
also possible on theft-deterrent
system-equipped vehicles.

System malfunctions or warnings are
indicated by the following warning lights
or beeps.
For vehicles with the type A/type B
instrument cluster, check the displayed
message for more information and, if
necessary, have the vehicle inspected at an
Authorized Mazda Dealer, according to
the indication.
ï‚·KEY Warning Light (Red)
Refer to Contact Authorized Mazda
Dealer and Have Vehicle Inspected on
page 7-27.
Refer to Taking Action on page 7-34.
ï‚·Ignition Not Switched Off (STOP)
Warning Beep
Refer to Ignition Not Switched Off
(STOP) Warning Beep on page 7-45.
ï‚·Key Removed from Vehicle Warning
Beep
Refer to Key Removed from Vehicle
Warning Beep on page 7-45.
If you have a problem with the key,
consult an Authorized Mazda Dealer.

Before Driving
Keys
3-3
CX-5_8HH4-EA-19A_Edition1 2018-11-21 10:03:20

If your key is lost or stolen, consult an
Authorized Mazda Dealer as soon as
possible for a replacement and to make the
lost or stolen key inoperative.
CAUTION
Radio equipment like this is governed by
laws in the United States.
Changes or modifications not expressly
approved by the party responsible for
compliance could void the user's authority
to operate the equipment.
NOTE
ï‚·The keyless entry system operation may
vary due to local conditions.
ï‚·The keyless entry system is fully
operational (door/liftgate lock/unlock)
when the ignition is switched off. The
system does not operate if the ignition is
switched to any position other than off.
ï‚·If the key does not operate when
pressing a button or the operational
range becomes too small, the battery
may be weak. To install a new battery,
refer to Key Battery Replacement (page
6-44).
ï‚·Battery life is about 1 year. Replace the
battery with a new one if the KEY
indicator light (green) flashes in the
instrument cluster (for vehicles with a
type A/type B instrument cluster (page
4-13, 4-30), messages are displayed
in the instrument cluster). Replacing the
battery about once a year is
recommended because the KEY warning
light/indicator light may not illuminate
or flash depending on the rate of battery
depletion.
ï‚·Additional keys can be obtained at an
Authorized Mazda Dealer. Up to 6 keys
can be used with the keyless functions
per vehicle. Bring all keys to an
Authorized Mazda Dealer when
additional keys are required.
Before Driving
Keys
3-4
CX-5_8HH4-EA-19A_Edition12018-11-21 10:03:20

About the SCR system
WA R N I N G
Be careful not to allow the DEF to run out. If the DEF completely runs out, the SCR system will
not operate normally:
If the vehicle runs out of DEF, the vehicle speed is restricted in steps to prevent contaminants
from being exhausted. When the remaining dist ance-to-empty reaches 0 km (0 miles) in the
final stage, the engine is forced
to idle. For replenishment of the DEF supply, consult an
Authorized Mazda Dealer.
CAUTION
Use a Mazda genuine product or a product conforming to ISO22241-1 for DEF. If
incompatible DEF is used, the SCR system may not operate normally. For the recommended
DEF, consult the nearest Authorized Mazda Dealer.
NOTE
ï‚·When the remaining distance-to-empty is 640 km (400 miles) or shorter while the DEF
warning indication is displayed, the SCR warning light turns on and the vehicle speed is
restricted. In addition, if there is a problem with the SCR system/DEF and the remaining
distance-to-empty is 200 km (125 miles) or sh orter, the SCR warning light flashes and the
vehicle speed is restricted.
ï‚·DEF needs to be replenished periodically according to the scheduled maintenance
information. If a warning message is displa yed in the multi-information display or the
SCR warning light flashes, consult an Authorized Mazda Dealer.
ï‚·Normally, the vehicle can be driven about 12,000 km (7,500 miles) before the DEF needs
to be replenished.
Before Driving
Fuel and Emission
3-31
CX-5_8HH4-EA-19A_Edition1 2018-11-21 10:03:20

4When Driving
Information concerning safe driving and stopping.
Start/Stop Engine.............................. 4-4 Ignition Switch........ ..................... 4-4
Starting the Engine....................... 4-5
Turning the Engine Off...............4-10
Instrument Cluster and Display ............
........................................................... 4-12 Instrument Cluster and
Display........................................4-12
Instrument Cluster (Type A)....... 4-13
Instrument Cluster (Type B)....... 4-30
Instrument Cluster (Type C)....... 4-46
Active Driving Display
*............. 4-58
Manual Transaxle Operation......... 4-61 Manual Transaxle Shift
Pattern......................................... 4-61
Automatic Transaxle....................... 4-64 Automatic Transaxle
Controls...................................... 4-64
Shift-Lock System...................... 4-65
Transaxle Ranges........................4-65
Manual Shift Mode..................... 4-67
Driving Tips................................4-72
Switches and Controls..................... 4-73
Lighting Control......................... 4-73
Fog Lights
*................................. 4-78
Turn and Lane-Change
Signals........................................ 4-79
Windshield Wipers and
Washer........................................ 4-80
Rear Window Wiper and
Washer........................................ 4-83
Rear Window Defogg er.............. 4-84
Horn............................................ 4-86
Hazard Warning Flasher............. 4-86
HomeLink Wireless Control System
(Type A)
*.................................... 4-87
HomeLink Wireless Control System
(Type B)
*.................................... 4-90
Brake................................................ 4-95 Brake System.............................. 4-95
AUTOHOLD............................ 4-100
Hill Launch Assist (HLA)........ 4-104
ABS/TCS/DSC............................... 4-106 Antilock Brake System
(ABS)........................................4-106
Traction Control System
(TCS)........................................ 4-107
Dynamic Stability Control
(DSC)........................................4-109
Fuel Economy Monitor................. 4-110 Fuel Economy Monitor
*........... 4-110
*Some models.4-1
CX-5_8HH4-EA-19A_Edition1 2018-11-21 10:03:20

This is for improved exhaust gas
purification and does not indicate any
parts defect.
ï‚·Engine-starting is controlled by the
spark ignition system.
This system meets all Canadian
Interference-Causing Equipment
Standard requirements regulating the
impulse electrical field strength of radio
noise.
1. Make sure you are carrying the key.
2. Occupants should fasten their seat belts.
3. Make sure the parking brake is on.
4. Continue to press the brake pedal firmly until the engine has completely
started.
5. (Manual transaxle)
Continue to press the clutch pedal
firmly until the engine has completely
started.
(Automatic transaxle)
Put the vehicle in park (P). If you must
restart the engine while the vehicle is
moving, shift into neutral (N).
NOTE
ï‚·(Manual transaxle)
The starter will not operate if the
clutch pedal is not depressed
sufficiently.
ï‚·(Automatic transaxle)
The starter will not operate if the
selector lever is not in P or N
position and the brake pedal is not
depressed sufficiently.
6. Verify that the KEY indicator light
(green) (if equipped) in the instrument
cluster and the push button start
indicator light (green) illuminate.
Indicator light
Push button start
NOTE
ï‚·If the push button start indicator
light (green) flashes, make sure that
the key is being carried (for vehicles
with a type A/type B instrument
cluster (page 7-24), messages are
displayed in the instrument cluster).
ï‚·If the push button start indicator
light (green) flashes with the key
being carried, touch the key to the
push button start and start the
engine (for vehicles with a type A/
type B instrument cluster (page
7-24), messages are displayed in
the instrument cluster). Refer to
Engine Start Function When Key
Battery is Dead on page 4-8.
When Driving
Start/Stop Engine
4-6
CX-5_8HH4-EA-19A_Edition1 2018-11-21 10:03:20

CAUTION
If the KEY warning light (red)
illuminates, or the push button start
indicator light (amber) flashes, this
could indicate a problem with the
engine starting system. This may
prevent the engine from starting or
from switching the ignition to ACC or
ON (for vehicles with a type A/type B
instrument cluster (page 7-24),
messages are displayed in the
instrument cluster). Have your vehicle
inspected at an Authorized Mazda
Dealer as soon as possible.
NOTE
ï‚·Under the following conditions, the
KEY warning light (red) flashes after
the push button start is pressed. This
informs the driver that the push
button start will not switch to ACC,
even if it is pressed from off (for
vehicles with a type A/type B
instrument cluster (page 7-24),
messages are displayed in the
instrument cluster).
ï‚·The key battery is dead.
ï‚·The key is out of operational
range.
ï‚·The key is placed in areas where it
is difficult for the system to detect
the signal (page 3-8).
ï‚·A key from another manufacturer
similar to the key is in the
operational range.
ï‚·(Forced engine starting method)
If the KEY warning light (red)
illuminates, or the push button start
indicator light (amber) flashes, this
could indicate that the engine may
not start using the usual starting
method (for vehicles with a type A/
type B instrument cluster (page
7-24), messages are displayed in
the instrument cluster). Have your
vehicle inspected at an Authorized
Mazda Dealer as soon as possible. If
this occurs, the engine can be
force-started. Press and hold the
push button start until the engine
starts. Other procedures necessary
for starting the engine, such as
having the key in the cabin, and
depressing the clutch pedal (manual
transaxle) or the brake pedal
(automatic transaxle) are required.
ï‚·When the engine is force-started, the
KEY warning light (red) (if
equipped)remains illuminated and
the push button start indicator light
(amber) remains flashing.
ï‚·(Automatic transaxle)
When the selector lever is in the
neutral (N) position, the KEY
indicator light (green) (if
equipped)and the push button start
indicator light (green) do not
illuminate.
7. Press the push button start after both
the KEY indicator light (green) (if
equipped)in the instrument cluster and
the push button start indicator light
(green) illuminate.
When Driving
Start/Stop Engine
4-7
CX-5_8HH4-EA-19A_Edition1 2018-11-21 10:03:20