lock MAZDA MODEL CX-9 2016 Owners Manual (in English)

6–10
Maintenance and Care
Scheduled Maintenance
Canada residents
Maintenance Interval Number of months or kilometers (miles), whichever comes ¿ rst.
Months 6
12 18 24 30 36 42 48 54 60 66 72
×1000 km 8
16 24 32 40 48 56 64 72 80 88 96
×1000 miles 5
10 15 20 25 30 35 40 45 50 55 60
ENGINE
Drive belts I I
Engine oil & ¿ lter
*1 R
R R R R R R R R R R R
COOLING SYSTEM
Engine coolant
*2 Replace at ¿ rst 192,000 km (120,000 miles) or 10 years; after
that, every 96,000 km (60,000 miles) or 5 years.
Engine coolant level I
I I I I I I I I I I I
FUEL SYSTEM
Air ¿ lter I
I I I I I I I I I I I
Replace every 56,000 km (35,000 miles) or 3 years.
Fuel lines and hoses
*3 I I I
Hoses and tubes for emission
*3 I
IGNITION SYSTEM
Spark plugs Replace every 64,000 km (40,000 miles).
ELECTRICAL SYSTEM
Function of all lights I
I I I I I I I I I I I
CHASSIS and BODY
Brake lines, hoses and connections I I I
Brake and clutch À uid level I
I I I I I I I I I I I
Disc brakes Inspect every 24,000 km (15,000 miles) or 1 years.
Tire (Rotation)
*4 Rotate every 8,000 km (5,000 miles).
Tire inÀ ation pressure and tire wear *4 I
I I I I I I I I I I I
Steering operation and linkages I I I
Front and rear suspension, ball joints and wheel
bearing axial play I I I
Rear differential oil
*5
Transfer oil *5
Driveshaft dust boots I I I
Bolts and nuts on chassis and body T T T
Exhaust system and heat shields Inspect every 72,000 km (45,000 miles) or 5 years.
All locks and hinges L
L L L L L L L L L L L
Wa s h e r À uid level I
I I I I I I I I I I I
Emergency À at tire repair kit (if installed)
*6 Inspect annually.
$9@'%&"#@&EJUJPOJOEC


$9@'%&"#@&EJUJPOJOEC










6–13
Maintenance and Care
Scheduled Maintenance
Schedule 1
Maintenance Interval Number of months or kilometers, whichever comes ¿ rst
Months 6
12 18 24 30 36 42 48 54 60 66 72
×1000 km 10
20 30 40 50 60 70 80 90
100 110 120
ENGINE
Drive belts I I I
Engine oil & ¿ lter
*1 R
R R R R R R R R R R R
COOLING SYSTEM
Cooling system I I I
Engine coolant
*2 Replace at ¿ rst 200,000 km or 10 years; after that, every
100,000 km or 5 years
FUEL SYSTEM
Air ¿ lter R R R R R R
Fuel lines and hoses I
*3 I *3 I
Hoses and tubes for emission I
*3 I *3 I
Fuel ¿ lter Replace every 60,000 km
IGNITION SYSTEM
Spark plugs I
I I I I I I I I I I I
Replace every 64,000 km
CHASSIS and BODY
Brake lines, hoses and connections I I I I I I
Brake and clutch À uid level I
I I I I I I I I
Brake À uid R R R
Disc brakes I
I I I I I I I I I I I
Tire (Rotation)
*4 Rotate every 10,000 km
Tire inÀ ation pressure and tire wear *4 I
I I I I I I I I I I I
Steering operation and linkages I
I I I I I I I I I I I
Front and rear suspension, ball joints and wheel
bearing axial play I I I I I I
Rear differential oil
*5
Transfer oil *5
Driveshaft dust boots I I I I I I
Bolts and nuts on chassis and body T T T T T T
Exhaust system and heat shields I I I I I I
All locks and hinges L
L L L L L L L L L L L
Wa s h e r À uid level I
I I I I I I I I I I I
Emergency À at tire repair kit (if installed)
*6 Inspect annually.
$9@'%&"#@&EJUJPOJOEC


$9@'%&"#@&EJUJPOJOEC










6–23
Maintenance and Care
Owner Maintenance
Hood
WARNING
Always check that the hood is closed
and securely locked:
A hood that is not closed and securely
locked is dangerous as it could fl y open
while the vehicle is moving and block
the driver's vision which could result in
a serious accident.

Opening the Hood
1. With the vehicle parked, pull the
release handle to unlock the hood.


Release handle 2. Insert your hand into the hood opening,
slide the latch lever to the right, and lift
up the hood.


Lever

3. Grasp the support rod in the padded
area and secure it in the support rod
hole indicated by the arrow to hold the
hood open.


Pad
Support rod
$9@'%&"#@&EJUJPOJOEC


$9@'%&"#@&EJUJPOJOEC










6–25
Maintenance and Care
Owner Maintenance
Engine Compartment Overview

Engine oil dipstick
Brake fluid reservoir
Engine oil-filler cap
Fuse blockBattery
Cooling system capEngine coolant reservoir
Windshield washer fluid reservoir

$9@'%&"#@&EJUJPOJOEC


$9@'%&"#@&EJUJPOJOEC










6–32
Maintenance and Care
Owner Maintenance
Inspect À uid level in the washer À uid
reservoir; add À uid if necessary.

L


Use plain water if washer À uid is
unavailable.
But use only washer À uid in cold weather
to prevent it from freezing.
N O T E
Front and rear washer À uid is supplied
from the same reservoir.

Body Lubrication
All moving points of the body, such as
door and hood hinges and locks, should
be lubricated each time the engine oil is
changed. Use a nonfreezing lubricant on
locks during cold weather.

Make sure the hood's secondary latch
keeps the hood from opening when the
primary latch is released.
$9@'%&"#@&EJUJPOJOEC


$9@'%&"#@&EJUJPOJOEC










6–36
Maintenance and Care
Owner Maintenance
9. Slide the blade component and install it
to the wiper arm.



10. Slowly lower the wiper arm onto the
windshield.
Replacing Rear Window Wiper
Blade
When the wiper no longer cleans well, the
blade is probably worn or cracked.
Replace it.
CAUTION
To prevent damage to the wiper arm
and other components, do not move
the wiper by hand.

1. Remove the cover and raise the wiper
arm.


2. Firmly rotate the wiper blade to the
right until it unlocks, then remove the
blade.


$9@'%&"#@&EJUJPOJOEC


$9@'%&"#@&EJUJPOJOEC










6–48
Maintenance and Care
Owner Maintenance
*Some models.
CAUTION
When removing the lens or lamp unit
using a fl athead screwdriver, make
sure that the fl athead screwdriver does
not contact the interior terminal. If
the fl athead screwdriver contacts the
terminal, a short circuit may occur.

N O T E
 


y To replace the bulb, contact an
Authorized Mazda Dealer.
 


y Use the protective cover and carton for
the replacement bulb to dispose of the
old bulb promptly and out of the reach
of children.

Replacing Exterior Light Bulbs
Headlights (type A), Headlights/Daytime
running lights (type B), Front turn
signal lights (type A), Daytime running
lights/Parking lights (type A), Front
side-marker lights (type A), Signature
wing illumination (type A)
* , Fog lights * ,
Brake lights, Taillights, High-mount
brake light, Side turn signal lights, Rear
side-marker lights
The LED bulb cannot be replaced as a
single unit because it is an integrated unit.
The LED bulb has to be replaced with the
unit. We recommend an Authorized Mazda
Dealer when the replacement is necessary.
Front turn signal lights (type B),
Parking lights/Front side-marker lights
(type B)
N O T E
When replacing a bulb for the front turn
signal lights and parking lights/front
side-marker lights, turn the steering wheel
and change the direction in which the tires
are pointed to the position where the bulb
replacement can be done easily.
Turn the steering wheel after starting the
engine and stop the engine after you ¿ nish
turning the steering wheel.

1. If you are changing the right bulb, start
the engine, turn the steering wheel
all the way to the right, and turn off
engine. If you are changing the left
bulb, turn the steering wheel to the left,
and turn off engine.
2. Make sure the ignition is switched off,
and the headlight switch is off.
3. Turn the screw counterclockwise and
remove it.



$9@'%&"#@&EJUJPOJOEC


$9@'%&"#@&EJUJPOJOEC










6–49
Maintenance and Care
Owner Maintenance
4. Pull the center of each plastic retainer
and remove the retainers, and then
partially peel back the mudguard.


Removal
Installation

5. Disconnect the wiring harness by
releasing the clamp.



6. Turn the socket and bulb assembly
counterclockwise and remove it. 7. Disconnect the bulb from the socket.

Front turn signal lights



Parking lights/Front side-marker
lights



8. Install the new bulb in the reverse order
of the removal procedure.
N O T E
There will be no problem with
functionality with the wiring harness
disconnected in Step 5 left disconnected.
Therefore, there is no need to connect the
wiring harness.

$9@'%&"#@&EJUJPOJOEC


$9@'%&"#@&EJUJPOJOEC










6–50
Maintenance and Care
Owner Maintenance
Rear turn signal lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Remove the cover.



3. Turn the screws counterclockwise and
remove them.


4. Pull the unit rearward to remove it.



5. Disconnect the wiring harness by
releasing the clamp.



6. Turn the socket and bulb assembly
counterclockwise and remove it.



$9@'%&"#@&EJUJPOJOEC


$9@'%&"#@&EJUJPOJOEC










6–52
Maintenance and Care
Owner Maintenance
Reverse lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Remove the cover.



3. Disconnect the electrical connector
from the bulb by pressing the tab on the
connector with your ¿ nger and pulling
the connector.



4. Turn the socket and bulb assembly
counterclockwise and remove it.
5. Disconnect the bulb from the socket.



6. Install the new bulb in the reverse order
of the removal procedure.

License plate lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Wrap a À athead screwdriver with a soft
cloth to prevent damage to the lens,
and then remove the lens by carefully
prying on the edge of the lens with a
À athead screwdriver.
3. Disconnect the bulb by pulling it out.



4. Install the new bulb in the reverse order
of the removal procedure.

$9@'%&"#@&EJUJPOJOEC


$9@'%&"#@&EJUJPOJOEC