warning light MAZDA MODEL MPV 2002 (in English) User Guide

3-5
Knowing Your Mazda
Doors and Locks
Form No. 8Q44-EA-01K
When a power sliding door is completely
closed/opened and a power sliding door
open/close transmitter button is pressed
for 1 second or more, the door opens/
closes after the buzzer sounds.Panic button
You can use the button to turn on the
alarm, which allows you to signal for
attention in an emergency.
Turning on the alarm
Pressing the button once will trigger the
alarm for about 2 minutes and 30 seconds,
and do the following:
•The horn sounds intermittently.
•The hazard warning lights flash.
Turning off the alarm
Press any button on the transmitter.
Operating Power Sliding Doors with
Transmitter:
Opening or closing the power sliding
doors with the keyless entry system
transmitter while not watching the
doors move is dangerous. People or
animals could be injured when the
doors open along the rear sides and
back to the rear fender, or in closing.
Allowing children to use the
transmitter could result in serious
injuries despite the jam-safe feature.
Always be sure that the doorway and
rear fender area are clear before
activating the power sliding doors and
be particularly careful when using
the keyless entry system transmitter.
Be sure to view the doors opening or
closing and do not operate a door on
either side if you can’t fully see it.
Always make sure that you watch the
power sliding doors close completely
and be sure your children do not have
access to the transmitter.
WARNINGNOTE
•When a power sliding door is not
completely closed, pressing the
power sliding door open/close
transmitter button for 1 second or
more will open the door completely.
•Press the button to stop the power
sliding doors while they are
opening/closing.
NOTE
The alarm will work whether any door
or the liftgate is open or closed.
NOTE
If the LOCK and UNLOCK button are
pressed sequentially, the hazard
warning flasher may not flash
correctly.
J16L_EA.book Page 5 Friday, February 22, 2002 11:34 AM

3-16
Knowing Your Mazda
Doors and Locks
Form No. 8Q44-EA-01K
Opening/closing with door handles
When the power sliding doors are
completely closed and a door is slid by the
handle slightly in the direction of
opening, the door completely opens
automatically after the buzzer sounds.When the doors are completely open and
a door is slid by the handle 5 cm (2 in) in
the direction of closing, the doors will
completely close automatically after the
buzzer sounds.
Jam-safe equipment
While a door is opening/closing
electrically and the system detects a
person or an object in the sliding door’s
path, the door will slide in the reverse
direction automatically.
When the power sliding doors are sliding
in the opening direction and an
obstruction is detected in its path, the
buzzer sounds and the doors slide in the
opposite direction approximately 10 cm
(4 in) and stop. When the doors are
sliding in the closing direction and an
obstruction is detected, the buzzer sounds
and the doors open completely.
NOTE
•If a rear power sliding door switch
is pressed again while the buzzer is
sounding, the operation can be
canceled.
•Press a rear power sliding door
switch to stop the power sliding
doors while they are opening/
closing.
Left power sliding
door switch
Exterior door
handleInterior door
handle
Check Area Around Power Sliding
Doors Before Operating:
Not checking for occupants and
objects around a power sliding door
before opening/closing it is
dangerous. The jam-safe equipment
is designed to prevent jamming in the
event an obstruction is in the sliding
door’s path. However, if the jam-safe
function detects an obstruction and
slides the door in the reverse
direction, and occupant in the door’s
path could be seriously injured.
Always check the area around the
power sliding doors before opening/
closing them.
WARNING
J16L_EA.book Page 16 Friday, February 22, 2002 11:34 AM

3-22
Knowing Your Mazda
Doors and Locks
Form No. 8Q44-EA-01K
Open or close a swing-out rear quarter
window by releasing the latch and moving
the window.

Opening a Window
Pull the latch inward and then push the
window outward.

Closing a Window
Pull the latch inward and then push it
backward until it snaps shut. Make sure
the window is securely closed.
Rear Quarter WindowsFuel-Filler Lid and Cap
Fuel Spray:
Fuel spray is dangerous. Fuel can
burn skin and eyes and cause illness
when ingested. Fuel spray is released
when there is pressure in the fuel
tank and the fuel cap is removed too
quickly. When removing the fuel cap,
loosen the cap slightly and wait for
any hissing to stop. Then remove it.
Fuel Vapor:
Fuel vapor is dangerous. It could be
ignited by sparks or flames causing
serious burns and injuries. Before
refueling, stop the engine, and always
keep sparks and flames away from the
filler neck.
Always use only a genuine Mazda fuel
cap or an approved equivalent,
available at Authorized Mazda
Dealers. The wrong cap can result in a
serious malfunction of the fuel and
emission control systems. It may also
cause the check engine light in the
instrument cluster to illuminate.
WARNING
CAUTION
J16L_EA.book Page 22 Friday, February 22, 2002 11:34 AM

3-27
Knowing Your Mazda
Form No. 8Q44-EA-01K
Security System
The optional immobilizer system allows
the engine to start only with a key the
system recognizes.
If someone attempts to start the engine
with an unrecognized key, the engine will
not start, thereby helping to prevent the
theft of your vehicle.

Immobilizer System Warning
Light
If the immobilizer system is working
properly, the light will come on when the
ignition switch is turned to the ON or
START position. The light will go out
when confirmation by the immobilizer
system is completed.
If the light flashes rapidly, fails to come
on, or comes on and stays on, it indicates
a system malfunction. If any of these
occur, contact an Authorized Mazda
Dealer as soon as possible.Immobilizer System
Changes or modifications not
expressly approved by Mazda could
void the user’s authority to operate the
equipment.
NOTE
This device complies with part 15 of
the FCC Rules and with RSS-210 of
Industry Canada. Operation is subject
to the following two conditions: (1)
This device may not cause harmful
interference, and (2) this device must
accept any interference received,
including interference that may cause
undesired operation. (Outside
transmissions may momentarily
interfere with the device’s operation.)
CAUTION
NOTE
•If the warning light comes on and
stays on when the ignition switch is
turned to the ON position, the
engine will not start.
•Signals from a TV or radio station,
or from a transceiver or a mobile
telephone, could interfere with your
immobilizer system. If you are
using the proper key and your
engine fails to start, check the
warning light. If it is flashing,
remove the ignition key and wait 2
seconds or more, then reinsert it and
try starting the engine again. If it
doesn’t start after 3 or more tries,
contact an Authorized Mazda
Dealer.
•If the warning light flashes
continuously while you are driving,
don’t shut off the engine. Go to an
Authorized Mazda Dealer and have
it checked. If you shut off the
engine while the light is flashing
you won’t be able to restart it.
J16L_EA.book Page 27 Friday, February 22, 2002 11:34 AM

3-29
Knowing Your Mazda
Security System
Form No. 8Q44-EA-01K
The optional theft-deterrent system is
designed to prevent your vehicle or its
contents from being stolen when all the
doors, hood, and liftgate are locked.
If forcible entry is attempted, the system
sounds the horn and flashes the hazard
warning lights.
The system won’t function unless it’s
properly armed. So when you leave the
vehicle, lock all the doors and the liftgate,
close all the windows, take your key, your
transmitter, and make sure the security
indicator light is flashing.

Operation
What turns it on:
•Forcing open a door, the hood or the
liftgate.
•Opening a door or the hood by
operating an inside door-lock button or
the hood release handle.
What it does:
•The horn sounds intermittently and the
hazard warning lights flash.
•The alarm continues for about 3
minutes, then stops.
If the system is triggered again, the lights
and horn will activate until a door or the
liftgate is unlocked with the key or with
the transmitter.

How to Arm the System
1. Remove the ignition key.
2. Close the hood. Then close all doors
and the liftgate and lock them from the
outside using the key in the door. If you
have the keyless entry system, press the
LOCK button on the transmitter. The
hazard warning lights will flash one
time to indicate that the system is
armed.
The following method will also arm the
theft-deterrent system:
Close the hood. Press the area on the
door-lock switch marked "DOOR
LOCK" once. Close all doors and the
liftgate.
3. The indicator light flashes once every 3
seconds to indicate that the system is
fully armed. It continues to flash until
the theft-deterrent system is turned off.
Theft-Deterrent System
NOTE
The theft-deterrent system operates
without the keyless entry system
transmitter, as well.
NOTE
Locking the doors with the inside
door-lock button will not arm the
system.
J16L_EA.book Page 29 Friday, February 22, 2002 11:34 AM

3-30
Knowing Your Mazda
Security System
Form No. 8Q44-EA-01K

To Tu r n o f f a n A r m e d S y s t e m
An armed system can be turned off by any
one of the following methods:
•Unlock a door or the liftgate with the
key.
•Press the UNLOCK button on the
keyless entry system transmitter.
•Insert the key into the ignition and turn
in to the ON position.
The hazard warning lights will flash twice
to indicate that the system is turned off.

To Stop an Alarm
A triggered alarm can be turned off by any
one of the following methods:
•Unlock a door or the liftgate with the
key.
•Press the UNLOCK button on the
keyless entry system transmitter.

Theft-Deterrent Labels
Labels indicating that your vehicle is
equipped with a Theft-Deterrent System
are in the glove box.
Mazda recommends that you affix them to
the lower rear corner of the front door
windows.
NOTE
If you have any problem with the theft-
deterrent system, consult an
Authorized Mazda Dealer.
J16L_EA.book Page 30 Friday, February 22, 2002 11:34 AM

3-32
Knowing Your Mazda
Steering Wheel and Mirrors
Form No. 8Q44-EA-01K
2. Depress the perimeter switch in the
appropriate direction.
After adjusting the mirror, lock the
control by moving the selector switch to
the middle position.
Folding the mirror
Fold the outside mirror rearward until it is
flush with the vehicle.Mirror defroster
To turn on the mirror defroster, turn the
ignition on and push the rear window
defroster switch (page 5-36).

Rearview Mirror (With Day/
Night Function)
Before driving, adjust the rearview mirror
to center on the scene through the rear
window.
Do this with the day/night lever in the day
position.
Push the lever forward for day driving.
Pull it back to reduce glare from
headlights.
Perimeter switch Selector switch
Driving with Mirrors Folded In:
Driving with the outside mirrors
folded in is dangerous. Your rear view
will be restricted, and you could have
an accident. Always return the
outside mirrors to the driving position
before you start driving.
WARNING
Day/Night lever
Day
Night
J16L_EA.book Page 32 Friday, February 22, 2002 11:34 AM

4-6
Before Driving Your Mazda
Form No. 8Q44-EA-01K
Before Starting the Engine
•Be sure the windows, outside mirror(s),
and outside lights are clean.
•Inspect inflation pressures and
condition of tires.
•Look under the vehicle for any sign of
a leak.
•If you plan to back up, make sure
nothing will be in your way.•Are all doors closed and locked?
•Are the inside and outside mirrors
adjusted?
•Is everyone’s seat belt fastened?
•Do all the lights work?
•Check all gauges.
•Check all warning lights when the
ignition switch is turned to the ON
position.
•Release the parking brake and make
sure the parking brake warning light
goes off.
Always be thoroughly familiar with your
Mazda.
Before Getting In
NOTE
Engine oil, engine coolant, brake fluid,
washer fluid, and other fluid levels
should be inspected daily, weekly, or at
refueling, depending on the fluid. See
Maintenance, Section 8.
After Getting In
J16L_EA.book Page 6 Friday, February 22, 2002 11:34 AM

4-8
Before Driving Your Mazda
Driving Tips
Form No. 8Q44-EA-01K
When driving on ice or in water, snow,
mud, sand, or similar hazard:
•Be cautious and allow extra distance
for braking.
•Avoid sudden braking and quick
steering.
•If your vehicle is not equipped with
ABS, brake with the pedal by using a
light up-down motion. Don’t hold the
pedal down constantly.
If your vehicle is equipped with ABS,
don’t pump the brakes. Continue to
press down on the brake pedal.
•If you get stuck, shift to 2 or 3 and
accelerate slowly. Don’t spin the front
wheels.
•For more traction in starting, use sand,
rock salt, chains, carpeting, or other
nonslip material under the front
wheels.If you must rock the vehicle to free it from
snow, sand, or mud, depress the
accelerator slightly and slowly move the
shift lever from D to R.
Hazardous Driving
Downshifting on Slippery Surfaces:
Downshifting into lower gear while
driving on slippery surfaces is
dangerous. The sudden change in tire
speed could cause the tires to skid.
This could lead to loss of vehicle
control and an accident. If it is
necessary to downshift on slippery
surfaces, be very careful.
NOTE
Use snow chains only on the front
wheels.
WARNING
Rocking the Vehicle
Spinning the Wheels:
When the vehicle is stuck, spinning
the wheels at high speed is dangerous.
The spinning tire could overheat and
explode. This could cause serious
injuries. Don’t spin the wheels at
more than 56 km/h (35 mph), and
don’t allow anyone to stand behind a
wheel when pushing the vehicle.
Too much rocking may cause engine
overheating, transaxle failure, and tire
damage.
WARNING
CAUTION
J16L_EA.book Page 8 Friday, February 22, 2002 11:34 AM

4-10
Before Driving Your Mazda
Driving Tips
Form No. 8Q44-EA-01K

Tire Chains
Check local regulations before using tire
chains.
Install the chains on the front tires.
Don’t use chains on the rear tires.
Use only SAE Class "S" chains, and make
sure they fit.
Installing the chains
1. Remove the wheel covers, or the chain
bands will scratch them.
2. Secure the chains on the front tires as
tightly as possible. Always follow the
chain manufacturer’s instructions.
3. Retighten the chains after driving
1/2—1 km (1/4—1/2 mile). •Chains may scratch or chip
aluminum wheels. Install tire chains
on steel wheels only.
•Chains may affect handling.
•Don’t go faster than 50 km/h (30
mph) or the chain manufacturer’s
recommended limit, whichever is
lower.
•Drive carefully and avoid bumps,
holes, and sharp turns.
•Avoid locked-wheel braking.
•Don’t use chains on the temporary
tire; it may result in damage to the
vehicle and to the tire.
•Don’t use chains on roads that are
free of snow or ice. The tires and
chains could be damaged.
CAUTION
Driving In Flooded Area
Driving with Wet Brakes:
Driving with wet brakes is dangerous.
Increased stopping distance or the
vehicle pulling to one side when
braking could result in a serious
accident. Light braking will indicate
whether the brakes have been
affected. Dry the brakes by driving
very slowly and applying the brakes
lightly until brake performance
returns to normal.
Make sure water does not enter the
vehicle interior or the engine area. The
vehicle interior could become wet or
the engine could be damaged.
WARNING
CAUTION
J16L_EA.book Page 10 Friday, February 22, 2002 11:34 AM