lock MAZDA MODEL MPV 2002 (in English) Manual PDF

5-26
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8Q44-EA-01K

Charging System Warning Light
This warning light comes on when the
ignition switch is turned to the ON
position and goes off when the engine is
started.
If the warning light comes on while
driving, it indicates a malfunction of the
alternator or of the charging system.
Drive to the side of the road and park off
the right-of-way. Consult an Authorized
Mazda Dealer.

Engine Oil Pressure Warning
Light
This warning light indicates low engine
oil pressure.
If the light comes on while driving:
1. Drive to the side of the road and park
off the right-of-way.
Brake Warning Light:
Driving with the brake system
warning light on is dangerous. It
indicates that your brakes may not
work at all or that they could
completely fail at any time. If this
light remains on, have the brakes
inspected immediately. Don’t drive
with this light on, and contact an
Authorized Mazda Dealer to have the
brakes inspected as soon as possible.
ABS Warning Light and Brake
Warning Light on at the Same Time:
Driving when the brake system
warning light and ABS warning light
are on at the same time is dangerous.
When both lights are on, the rear
wheels could lock more quickly in an
emergency stop than under normal
circumstances.
Don’t drive with both lights on, and
contact an Authorized Mazda Dealer
to have the brakes inspected as soon
as possible.
WARNING
Don’t continue driving when the
charging system warning light is
illuminated.
CAUTION
J16L_EA.book Page 26 Friday, February 22, 2002 11:34 AM

5-27
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8Q44-EA-01K
2. Turn off the engine and inspect the
engine oil level (page 8-9). If it’s low,
add oil.
3. Check the light.
If the light remains on even after you add
oil, have your vehicle towed to the nearest
service station or to an Authorized Mazda
Dealer.

Check Engine Light
If this light comes on while driving, the
vehicle may have a problem. It is
important to note the driving conditions
when the light came on and consult an
Authorized Mazda Dealer.
The check engine light may come on in
the following cases:
•The fuel tank level being very low or
approaching empty.
•The engine’s electrical system has a
problem.
•The emission control system has a
problem.
•The fuel-filler cap is missing or not
tightened securely.If the check engine light flashes
continuously, decrease your speed and
consult an Authorized Mazda Dealer as
soon as possible.

ABS Warning Light
The warning light stays on for a few
seconds when the ignition switch is turned
to the ON position.
If the ABS warning light stays on while
you’re driving, the ABS control unit has
detected a system malfunction. If this
occurs, your brakes will function
normally as if the vehicle had no ABS.
Should this happen, consult an Authorized
Mazda Dealer as soon as possible. Don’t run the engine if oil pressure is
low. It could result in extensive engine
damage.
CAUTION
ABS Warning Light and Brake
Warning Light on at the Same Time:
Driving when the brake system
warning light and ABS warning light
are on at the same time is dangerous.
When both lights are on, the rear
wheels could lock more quickly in an
emergency stop than under normal
circumstances.
Don’t drive with both lights on, and
contact an Authorized Mazda Dealer
to have the brakes inspected as soon
as possible.
WARNING
J16L_EA.book Page 27 Friday, February 22, 2002 11:34 AM

5-31
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8Q44-EA-01K

Seat Belt Warning Beep
If the driver’s seat belt is not fastened
when the ignition switch is turned to the
ON position, a beep will sound for about
6 seconds.

Ignition Key Reminder
If the ignition switch is in the LOCK or
ACC position, a beep will sound when the
driver’s door is opened.

Lights-On Reminder
If lights are on and the key is removed
from the ignition switch, a beep will
sound when the driver’s door is opened.

Power Sliding Door Buzzer
The buzzer sounds according to the power
sliding door operation.
If there is a malfunction in the power
sliding door system, the buzzer sounds
continuously. If this happens, press the
power sliding doors main switch to the
OFF position and the buzzer will stop.
Consult your nearest Authorized Mazda
Dealer to have the power sliding doors
checked.
Refer to Power Sliding Doors on page 3-
12.
Beeps
J16L_EA.book Page 31 Friday, February 22, 2002 11:34 AM

5-34
Driving Your Mazda
Switches and Controls
Form No. 8Q44-EA-01K
Use this switch to turn on the fog lights.
They help you to see as well as to be seen.
To turn on the fog lights, first turn on the
headlight switch. Then press the fog light
switch.
To turn the fog lights off, press the fog
light switch again or turn the headlight
switch off.The ignition switch must be in the ON
position.
Fog LightsWindshield Wipers and
Washer
Frozen Washer Fluid:
Using windshield washer fluid in
freezing temperatures is dangerous.
The washer fluid could freeze on the
windshield and block your vision.
You could have an accident. Don’t use
the washer without first warming the
windshield.
NOTE
Because heavy ice and snow can jam
the wiper blades, the wiper motor is
protected by a circuit breaker. This
mechanism will automatically stop
operation of the blades, but only for
about 5 minutes.
If this happens, turn off the wiper
switch and park off the right-of-way,
and remove the snow and ice.
After 5 minutes, turn on the switch and
the blades should operate normally. If
they don’t resume functioning, consult
an Authorized Mazda Dealer as soon
as possible.
WARNING
J16L_EA.book Page 34 Friday, February 22, 2002 11:34 AM

6-5
Interior Comfort
Climate Control System
Form No. 8Q44-EA-01K

Control Switches
Temperature control dial
This dial controls temperature. Turn it
clockwise for hot and counterclockwise
for cold.Fan control dial
This dial allows variable fan speeds.
0—Fan off
1—Low speed
2—Medium low speed
3—Medium high speed
4—High speed
Control Panel (Front)
A/C0123
4
0123REAR
Temperature control dialA/C switch Rear window defroster switchFan control dial
Air intake selector switch
Rear air-conditioner main switchMode selector dial
(page 5-36)
ColdHot
J16L_EA.book Page 5 Friday, February 22, 2002 11:34 AM

6-13
Interior Comfort
Climate Control System
Form No. 8Q44-EA-01K
Fan control dial
This dial allows variable fan speeds.
0
—Fan off
1
—Low speed
2
—Medium speed
3
—High speed
Temperature control dial (Type B)
This dial controls temperature. Turn it
clockwise for hot and counterclockwise
for cold.Mode selector dial (Type B)
Turn the mode selector dial to select
airflow mode (page 6-11).
NOTE
When the rear air-conditioner main
switch is not set to the REAR position,
the fan control dial of the rear air-
conditioner control panel does not
work.
The front air-conditioner controls
override the rear controls.
021
3
Hot Cold
J16L_EA.book Page 13 Friday, February 22, 2002 11:34 AM

6-14
Interior Comfort
Form No. 8Q44-EA-01K
Audio System

Detachable Type
To remove the antenna, turn it
counterclockwise.
To install the antenna, turn it clockwise.
Make sure the antenna is security
installed.
Radio Reception
AM characteristics
AM signals bend around such things as
buildings or mountains and bounce off the
ionosphere. Therefore, they can reach
longer distances than FM signals. Because
of this, two stations may sometimes be
picked up on the same frequency at the
same time.
FM characteristics
An FM broadcast range is usually about
40—50 km (25—30 miles) from the
source. Because of extra coding needed to
break the sound into two channels, stereo
FM has even less range than monaural
(non-stereo) FM.
Antenna
To prevent damage to the antenna,
remove it before entering a car wash
facility or passing beneath a low
overhead clearance.
NOTE
When leaving your vehicle unattended,
we recommend that you remove the
antenna and store it inside the vehicle.
CAUTION
Operating Tips for Audio
System
Ionosphere
Station 1 Station 2
FM Station
40—50 km
(25—30 miles)
J16L_EA.book Page 14 Friday, February 22, 2002 11:34 AM

6-21
Interior Comfort
Au di o S ys t em
Form No. 8Q44-EA-01K
Power/Volume/Sound Controls ............................................................................................. 6-22
Clock ..................................................................................................................................... 6-24
Operating the Radio ............................................................................................................... 6-26
Operating the Cassette Tape Player ....................................................................................... 6-28
Operating the Mini Disc (MD) Player ................................................................................... 6-30
Operating the Compact Disc (CD) Player ............................................................................. 6-32
Operating the In-Dash CD Changer ...................................................................................... 6-34
Error Indications .................................................................................................................... 6-37
Audio Set
CD Player In-dash CD Changer
Cassette Tape Player Mini Disc (MD) PlayerIllustration is of a representative audio unit.
J16L_EA.book Page 21 Friday, February 22, 2002 11:34 AM

6-24
Interior Comfort
Au di o S ys t em
Form No. 8Q44-EA-01K

Clock
Setting the time
The clock can be set at any time when the
ignition switch is in the ACC or ON
position.
1. To adjust the time, press the clock
button ( ) for about 2 seconds
until a beep is heard.
The clock’s current time will flash.
2. To advance the hours, press the hour
set button ( ). To advance the
minutes, press the minute set button
( ) while the time is flashing.
3. Press the clock button ( ) again
to start the clock.Exact hour adjustment 1. To set the exact hour, press the clock
button ( ) for about 2 seconds
until a beep is heard.
The clock’s current time will flash.
2. Press the clock button ( ) again
and the time will be adjusted as
follows:
(Example)
12:01—12:29
→12:00
12:30—12:59
→1:00
Display
Clock button
Hour set
button
Minute set
button
NOTE
If the power supply to the unit is
interrupted (if the fuse blows or the
vehicle’s battery is disconnected), the
clock will need to be reset.
J16L_EA.book Page 24 Friday, February 22, 2002 11:34 AM

6-25
Interior Comfort
Au di o S ys t em
Form No. 8Q44-EA-01K
Changing the display mode
The display on the unit can be changed by
pressing the clock button ( ). This
alternates the display between time and
audio. When the clock mode has been
selected, the time will be displayed.
NOTE
If audio operation is selected while the
time mode is on, the selected audio
mode will be displayed for ten
seconds, then the display will revert to
the time mode.
J16L_EA.book Page 25 Friday, February 22, 2002 11:34 AM