warning MAZDA MODEL MX-30 EV 2022 Owners Manual

Refer to Accessory Sockets on page
5-39.

1. Compressor plug
2. Compressor
CAUTION
When inserting the air compressor
plug into or removing it from the
accessory socket, make sure that
the air compressor switch is off.
When turning the air compressor
on/o ff, use the air compressor
switch.
11.The sealant is injected into the tire when the air compressor is
switched on. After the sealant is
injected completely, wait until the
tire in flation pressure increases to
the specified tire in flation pressure.
NOTE
The infl ation pressure may increase
to about 300 kPa (3.1 kgf/cm2, 3
bar, 43.5 psi) temporarily to inject
the sealant through the valve.
Normally, the in flation pressure
decreases gradually and it reaches
the actual infl ation pressure after
about 30 seconds.
WARNING
Never use the air compressor
above 300 kPa (3.1 kgf/cm2, 3
bar, 43.5 psi):
Using the air compressor at an
in flation pressure above 300 kPa
(3.1 kgf/cm
2, 3 bar, 43.5 psi)
continuously is dangerous. If the air
compressor overheats, hot air will
be exhausted and you could get
burned.
NOTE
Check the tire in flation pressure
label rear door on the driver's
side for the correct tire in flation
pressure.
Do not operate the air
compressor for a continuous 10
minutes or longer because using
it for long periods could cause a
malfunction.
If the tire in flation pressure does
not increase, repair of the tire is
not possible. If the tire does not
reach the speci fied tire inflation
pressure within 10 minutes, it
may have received extensive
damage. In this case, the repair
using the emergency flat tire
repair kit was not successful.
Contact an Authorized Mazda
Dealer.
If Trouble Arises
Flat Tire
7-7
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

12.Adhere the speed restriction stickerto an area where it can be viewed
easily by the driver.

13.Adhere the repaired tire sticker tothe wheel of the flat tire.

WARNING
Do not adhere the speed
restriction sticker to the padded
area on the steering wheel:
Adhering the speed restriction
sticker to the padded area on the
steering wheel is dangerous
because the air bag may not
operate (deploy) normally resulting
in serious injury. In addition, do not
adhere the sticker to areas where
warning lights or the speedometer
cannot be viewed.
14.When the tire in flates to the
specified tire in flation pressure, turn
the air compressor switch o ff, turn
the sleeve of the injection hose to
the left, and pull it out of the tire
valve.
15.Remove the air compressor hose from the injection valve of the
bottle. After that, install the
injection hose to the injection valve
of the bottle to prevent leakage of
any remaining sealant.

CAUTION
The remaining sealant in the hose
may spray out when the hose is
removed. Remove the hose
carefully because you may not be
able to remove the sealant
contacting clothing or other
objects.
16.Install the tire valve cap.
17.Put the emergency flat tire repair kit
into the trunk.
18.Start driving immediately to spread the sealant in the tire.
CAUTION
Carefully drive the vehicle at a
speed of 80 km/h (50 mph) or less.
If the vehicle is driven at a speed of
80 km/h (50 mph) or more, the
vehicle may vibrate.
If Trouble Arises
Flat Tire
7-8
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

NOTE
If the tire is not properly inflated,
the tire pressure monitoring system
warning light will illuminate (page
4-180).
19.After driving the vehicle for about 10 minutes or 5 km (3 miles),
connect the air compressor to the
tire using Step 8 of the procedure,
and check the tire in flation pressure
using the tire pressure gauge on the
air compressor. If the tire in flation
pressure is lower than the speci fied
tire in flation pressure, turn the air
compressor on and wait until it
reaches the speci fied tire inflation
pressure.
WARNING
If the tire in flation pressure has
decreased below 130 kPa (1.3
kgf/cm
2 or bar, 18.9 psi), stop
driving and contact an Authorized
Mazda Dealer:
The repair using the emergency flat
tire repair kit was not successful.
If you see a decrease in the tire
infl ation pressure, even if Steps 8
to 19 of the procedure are
performed repeatedly, stop
driving:
Contact an Authorized Mazda
Dealer.
CAUTION
Before checking the tire in flation
pressure using the tire pressure
gauge, turn the air compressor
switch o ff.
20.The emergency flat tire repair is
completed successfully if the tire
in flation pressure does not
decrease. Carefully drive the vehicle
to the nearest Authorized Mazda
Dealer immediately and have the
fl at tire replaced. Replacement with
a new tire is recommended. If the
tire is to be repaired or reused,
consult an Authorized Mazda
Dealer.
NOTE
If an emergency flat tire repair has
been performed using the
emergency flat tire repair kit,
Mazda recommends that the tire
be replaced with a new one as
soon as possible. If the tire is to
be repaired or reused, consult an
Authorized Mazda Dealer.
The wheel can be reused if the
sealant adhering to it is removed.
However, replace the valve with a
new one.
▼ Inspecting the Emergency Flat Tire
Repair Kit
Inspect the emergency
flat tire repair
kit at regular intervals.
Check the tire sealant period of
e ff ective use.
Check the operation of the tire
compressor.
NOTE
The tire sealant has a period of
e
ff ective use. Check the period of
e ff ective use indicated on the bottle
label and do not use it if it has expired.
Have the tire sealant replaced at an
Authorized Mazda Dealer before the
period of eff ective use has expired.
If Trouble Arises
Flat Tire
7-9
MX-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

Jump-Starting
▼Jump-Starting
The lead-acid battery might be depleted
if the following conditions occur.
The EV system does not start.The selector lever cannot be shifted to a position other than P.The horn sound is weak or it does not sound.The brightness of the lights is extremely low.
Jump-starting is dangerous if done incorrectly. So follow the procedure carefully. If
you feel unsure about jump-starting, we strongly recommend that you have a
competent service technician do the work.
Using commercially available booster cables, connect the lead-acid battery of the
booster vehicle’s battery to the lead-acid battery of your vehicle and start the EV
system.
WARNING
Follow These Precautions Carefully:
To ensure safe and correct handling of the lead-acid battery, read the following
precautions carefully before using the lead-acid battery or inspecting it.
Keep flames and sparks away from open lead-acid battery cells and do not
allow metal tools to contact the positive (+) or negative (–) terminal of the
lead-acid battery when working near a lead-acid battery. Do not allow the
positive (+) terminal to contact the vehicle body:
Flames and sparks near open lead-acid battery cells are dangerous. Hydrogen gas,
produced during normal lead-acid battery operation, could ignite and cause the
lead-acid battery to explode. An exploding lead-acid battery can cause serious burns
and injuries. Keep all flames including cigarettes and sparks away from open
lead-acid battery cells.
If Trouble Arises
Depleted Lead-acid Battery
7-12
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

When towing a vehicle, transport it
with both front wheels raised o ff the
ground or with all front and rear
wheels raised o ff the ground.
If the vehicle is towed with the front
wheels grounded, the EV system may
be damaged.
This vehicle cannot be used to tow
other vehicles.
If towing service is not available in an
emergency, the vehicle may be towed
with all four wheels on the ground
using the tiedown hook at the front of
the vehicle.
If the vehicle has to be towed by rope
to move it such as in an emergency,
tow the vehicle in as short a distance
as possible such as to the transport
vehicle or to get unstuck. Otherwise,
the EV transaxle or EV system could be
damaged.
CAUTION
Follow these instructions when towing
the vehicle with all wheels on the
ground.
 Shift to the N position.
 Start the EV system.
 Release the parking brake.
Refer to Electric Parking Brake (EPB)
on page 4-52.
In the following cases, do not tow the
vehicle with rope. Otherwise, the EV
transaxle or EV system could be
damaged.
 The EV system does not start.
 The shift control system warning
indication/warning light displays/
turns on.
Do not stop the EV system while the
vehicle is being towed. Otherwise, the
parking lock may engage which could
lead to an accident.
Tiedown Hooks*
▼ Tiedown Hooks
CAUTION
Do not use the front and rear tiedown
eyelets for towing the vehicle.
They have been designed only for
securing the vehicle to a transport
vessel during shipping.
Using the eyelets for any other purpose
could result in the vehicle being
damaged.
1. Remove the tiedown eyelet and the
lug wrench from the luggage
compartment (page 7-3).
2. Wrap a flathead screwdriver or
similar tool with a soft cloth to
prevent damage to a painted
bumper, and open the cap located
on the front or rear bumper.
Front
If Trouble Arises
Emergency Towing
*Some models.7-19
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

If a Warning Light TurnsOn or Flashes
▼If a Warning Light Turns On or
Flashes
If any warning light turns on/
flashes,
take appropriate action for each light.
There is no problem if the light turns
o ff, however if the light does not turn
o ff or turns
on/flashes again, consult
an Authorized Mazda Dealer.
WARNING
If the warning light/indicator light
turns on or flashes, park the vehicle in
a safe place immediately and take
appropriate measures.
Continuing to drive the vehicle while
ignoring the illumination/ flashing of
the warning light/indicator light is
dangerous because a problem may
occur to a vehicle system, or it could
lead to an accident.
The details for some warnings can be
viewed on the center display or
multi-information display in the
instrument cluster.
Center display
1. Select “Information” on the home
screen.
2. Select “Vehicle Status Monitor”.
3. Select the applicable warning to view the warning details.
Multi-information display
1. Press the INFO switch on the steering switch to display the
warning indication screen.
Refer to Multi-information Display
on page 4-11.
▼Brake System Warning Indication/
Warning Light
This warning has the following
functions:
Warning light inspection
For an operation check, make sure that
the light turns on when the power
switch is switched on and turns o
ff a
few seconds later, or when the EV
system is started.
When the light turns on
If the brake system warning light
remains illuminated the brake fluid
may be low or there could be a
problem with the brake system. Park
the vehicle in a safe place immediately
and contact an Authorized Mazda
Dealer.
Refer to Inspecting Brake Fluid Level on
page 6-12.
WARNING
Do not drive with the brake system
warning light illuminated. Contact an
Authorized Mazda Dealer to have the
brakes inspected as soon as possible:
Driving with the brake system warning
light illuminated is dangerous. It
indicates that your brakes may not
work at all or that they could
completely fail at any time. If this light
remains illuminated, after checking
that the parking brake is fully released,
have the brakes inspected
immediately.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-21
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

CAUTION
In addition, the
eff ectiveness of the
braking may diminish so you may
need to depress the brake pedal
more strongly than normal to stop
the vehicle.
 When starting the EV system, the
brake system warning light may turn
on and the warning indication may
be displayed. In this case, park the
vehicle in a safe location and release
the brake pedal.
If the brake system warning light/
warning indication does not turn o ff
even after parking the vehicle, have
the vehicle inspected by an
Authorized Mazda Dealer.

▼ Electronic Brake Force Distribution
System Warning
If the electronic brake force
distribution control unit determines
that some components are operating
incorrectly, the control unit may
illuminate the brake system warning
light and the ABS warning light
simultaneously. The problem is likely to
be the electronic brake force
distribution system.
WARNING
Do not drive with both the brake
system warning light and ABS warning
light illuminated. Have the vehicle
towed to an Authorized Mazda
Dealer to have the brakes inspected as
soon as possible:
Driving when the brake system warning
light and ABS warning light are
illuminated simultaneously is
dangerous.
When both lights are illuminated, the
rear wheels could lock more quickly in
an emergency stop than under normal
circumstances.
▼ Lead-acid Battery Charging System
Warning Indication/Warning Light
The lead-acid battery charging system
warning indication/warning light
displays/turns on if the charging
system has a malfunction while the EV
system is operating.
Drive to the side of the road and park
o
ff the right-of-way. Consult an
Authorized Mazda Dealer.
WARNING
Do not drive the vehicle with the
lead-acid battery charging system
warning indication/warning light
displayed/turned on:
Otherwise, the EV system could stop
unexpectedly and the parking lock may
not operate which could result in an
accident.
▼ EV System Problem Warning
Indication/Warning Light
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-22
MX
-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

“EV System Malfunction. Have the
Vehicle Inspected” is displayed
The indication/light displays/turns on
if the system has a problem.
Have your vehicle inspected by an
Authorized Mazda Dealer.
“EV System Malfunction. Stop the
Vehicle in a Safe Location” is
displayed
The indication/light displays/turns on
if the system has a problem.
Park the vehicle in a safe place
immediately and contact an
Authorized Mazda Dealer.
“Electrical Leakage in EV System
Detected Stop the Vehicle in a Safe
Location” is displayed
The indication/light displays/turns on
if the system has a problem.
Park the vehicle in a safe place
immediately and contact an
Authorized Mazda Dealer.
WARNING
Do not open the hood:
If you touch something in the motor
compartment, it could lead to an
electrical shock resulting in an
accident.
CAUTION
If the light turns on while driving, the
EV system cannot be started when the
power switch is switched OFF once.
▼ High Voltage Battery Temperature
War n in g I nd ic at ion
“Excessive High Voltage Battery
Temperature. Drive Slowly” is
displayed
The indication displays if the high
voltage battery temperature is
excessively high.
Drive slowly to reduce load on the high
voltage battery.
Stop the vehicle in a safe place if
necessary. If the indication remains
displayed, the system may have a
problem. Have the vehicle inspected
by an Authorized Mazda Dealer.
“High Voltage Battery Temperature Is
Low Acceleration Is Limited” is
displayed
The indication displays if the high
voltage battery temperature is
excessively low.
The vehicle speed may not increase
even if the accelerator pedal is
depressed because the motor output is
restricted.
If the indication remains displayed, the
system may have a problem. Have the
vehicle inspected by an Authorized
Mazda Dealer.
▼Remaining High Voltage Battery
Power Warning Indication/
Warning Light
“High Voltage Battery Is Low. Charge
Battery Soon” displays/turns on
The indication displays when the
remaining high voltage battery power
is low.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-23
MX
-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

“High Voltage Battery Is Urgently Low
Charge Battery Immediately”
displays/flashing
The indication displays when the
remaining high voltage battery power
is 0.
“High Voltage Battery Is Depleted
Vehicle Cannot Be Driven Until
Battery Is Charged”
displays/flashing
The indication/light displays/ flashes
when the remaining high voltage
battery power is 0 and the vehicle
cannot be driven.
▼ Charging System Warning
Indication/Warning Light
The indication/light displays/turns on
if the charging system has a problem.
Have your vehicle inspected by an
Authorized Mazda Dealer as soon as
possible. Otherwise, the charging
system may not charge the battery.
▼Output Restriction Warning
Indication/Warning Light
“Acceleration Limited” displays/turns
on
The indication/light displays/turns on
under the following conditions. The
vehicle speed may not increase even if
the accelerator pedal is depressed
because the motor output is restricted.
EV system is protected from
overheating
High voltage battery level is lowHigh voltage battery temperature is
low
“Acceleration Limited” displays/
fl ashing
If the vehicle continues to be driven
with the output restriction warning
indication/warning light turned on,
the output restriction warning light
flashes.
The vehicle speed may not increase
even if the accelerator pedal is
depressed because the motor output is
further restricted compared to the
condition in which the output
restriction warning light turns on.
“Excessive EV System Temp.
Acceleration Limited Avoid Moving at
Very Low Speeds. Depress Brake
When Not Moving” displays/turns on
When the vehicle is stopped on an
upslope or the vehicle is driven at low
speed on an upslope with the selector
lever in the D or R position, the
indication/light may display/turn on.
If necessary, park the vehicle in a safe
place and let the EV system cool down
because the output is restricted until
the EV system returns to the normal
temperature.
WARNING
When the output restriction warning
indication/warning light displays/
turns on or flashes, check the safety of
the surroundings:
The motor output decreases and the
vehicle speed decreases resulting in an
accident. If the vehicle cannot be
driven safety, stop the vehicle in a safe
place.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-24
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

▼Power Steering Malfunction
Indication/Indicator Light
The electric power steering
malfunction indication/indicator light
displays/turns on if the electric power
steering has a malfunction.
If the electric power steering
malfunction indication/indicator light
displays/turns on, stop the vehicle in a
safe place and switch the power switch
OFF.
There is no problem if the display/
illumination of the electric power
steering malfunction indication/
indicator light turns o
ff when the EV
systems is restarted after some time
has passed. If the electric power
steering malfunction indication/
indicator light displays/turns on even
after the EV systems is restarted,
contact an Authorized Mazda Dealer.
NOTE
If the message is displayed, the
power steering will not operate
normally. In this case, the steering
wheel can still be operated,
however, the operation may feel
heavy compared to normal, or the
steering wheel could vibrate when
turning.
Repeatedly jerking the steering
wheel left and right while the vehicle
is stopped or moving extremely
slowly will cause the power steering
system to go into protective mode
which will make the steering feel
heavy, but this does not indicate a
problem. If this occurs, park the
vehicle safely and wait several
minutes for the system to return to
normal.
▼ Shift Control System Warning
Indication/Warning light
The indication/light displays/turns on
if the shift control system has a
malfunction.
“Shift Control System Malfunction
Stop the Vehicle in a Safe Location”
displays/turns on
There is a serious malfunction with the
shift control system.
Park the vehicle in a safe place
immediately and contact an
Authorized Mazda Dealer.
“Shift Control System Malfunction
Have the Vehicle Inspected” displays/
turns on
There is a malfunction with the shift
control system.
Have your vehicle inspected by an
Authorized Mazda Dealer.
“Vehicle Cannot Shift Into Park. Stop
the Vehicle in a Safe Location Then
Apply the Parking Brake” displays/
turns on
The vehicle cannot be held in a
stopped position even when the
selector lever is in the P position.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-25
MX
-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07