key MAZDA MODEL MX-5 2017 (in English) Owner's Manual

3–19
Before Driving
Doors and Locks
Opening and Closing the Trunk
Lid
Opening the trunk lid
Using the remote release button
Push the release button.



The remote release button function can
be disabled by locking the doors using
the transmitter, auxiliary key, or a request
switch to prevent an intruder in the vehicle
from opening the trunk.
To enable the remote release button
operation, unlock the doors by using the
transmitter, auxiliary key, or a request
switch, or switch the ignition ON.
N O T E
The remote release button cannot be
disabled by locking the doors using the
door-lock switch/door-lock knob.
Refer to Locking, Unlocking with Door-
Lock Switch on page 3-14 .
Refer to Locking, Unlocking with Door-
Lock Knob on page 3-17 .

Using the electric trunk lid opener
(With the advanced keyless function)
A trunk lid can also be opened while the
key is being carried.
Press the electric trunk lid opener and raise
the trunk lid when the latch releases.


Electric trunk lid
opener

N O T E
 


y When opening the trunk lid with the
doors locked, it may require a few
seconds for the trunk lid latch to release
after the electric trunk lid opener is
pressed.
 y The trunk lid can be closed when the
doors are locked with the key left in the
vehicle. However, to prevent locking the
key in the vehicle, the trunk lid can be
opened by pressing the electric trunk lid
opener. If the trunk lid cannot be opened
despite doing this procedure, ¿ rst push
the trunk lid completely closed, then
press the electric trunk lid opener to
fully open the trunk lid.
 


y If the vehicle battery is dead or there
is a malfunction in the electrical
system and the trunk lid cannot be
unlocked, the trunk lid can be opened by
performing the emergency procedure.
  Refer to When Trunk Lid Cannot be
Opened on page 7-52 .

/:A(4'#,A'FKVKQPKPFD/:A(4'#,A'FKVKQPKPFD

3–20
Before Driving
Doors and Locks
*Some models.
Closing the trunk lid
Use both hands to push the trunk lid down
until the lock snaps shut. Do not slam it.
Pull up on the trunk lid to make sure it is
secure. Inside Trunk Release
Lever
*
Your vehicle is equipped with an inside
trunk release lever that provides a means
of escape for children and adults in the
event they become locked inside the trunk.

No matter how careful adults might be
with keys and locking their cars, parents
should be aware that children may be
tempted to play around vehicles and use
the trunk as a hiding place.

Adults are advised to familiarize
themselves with the operation and location
of the inside trunk release lever so that
all children can be told about it in an
appropriate way, keeping in mind that
most vehicles do not have such levers.
WARNING
Close the trunk lid, do not allow children
to play inside the trunk:
Leaving the trunk lid open or leaving
children in the vehicle with the keys is
dangerous. Children could open the
trunk lid and climb inside resulting
in possible injury or death from heat
exposure.

Always keep the car from being a
tempting place to play by latching the
doors and the trunk, and keeping the
keys where children can not play with
them:
Leaving children or animals
unattended in a parked vehicle is
dangerous. Babies left sleeping and
children who lock themselves in cars or
trunks can die very quickly from heat
prostration. Do not leave your children
or pets alone in a car at any time. Do
not leave the car, the trunk unlocked.

/:A(4'#,A'FKVKQPKPFD/:A(4'#,A'FKVKQPKPFD

3–47
Before Driving
Security System
M o d i¿ cation and Add-On
Equipment
Mazda cannot guarantee the immobilizer
and the theft-deterrent systems' operation
if the system has been modi¿ ed or if any
add-on equipment has been installed.

CAUTION
To avoid damage to the vehicle, do
not modify the system or install any
add-on equipment to the immobilizer
and the theft-deterrent systems or the
vehicle.

Immobilizer System
The immobilizer system allows the
engine to start only with a key the system
recognizes.

If someone attempts to start the engine
with an unrecognized key, the engine
will not start, thereby helping to prevent
vehicle theft.
If you have a problem with the
immobilizer system or the key, consult an
Authorized Mazda Dealer.
CAUTION
 


¾ Radio equipment like this is governed by
laws in the United States.
  Changes or modifi cations not expressly
approved by the party responsible
for compliance could void the user's
authority to operate the equipment.
 


¾ To avoid damage to the key, do not: 



¾ Drop the key.



¾ Get the key wet.



¾ Expose the key to any kind of
magnetic fi eld.
 


¾ Expose the key to high temperatures
on places such as the dashboard or
hood, under direct sunlight.
 


¾ If the engine does not start with the
correct key, and the security indicator
light keeps illuminating or fl ashing, the
system may have a malfunction. Consult
an Authorized Mazda Dealer.

/:A(4'#,A'FKVKQPKPFD/:A(4'#,A'FKVKQPKPFD

3–48
Before Driving
Security System
N O T E
 


y The keys carry a unique electronic code.
For this reason, and to assure your
safety, obtaining a replacement key
requires some waiting time. They are
only available through an Authorized
Mazda Dealer.
 


y Always keep a spare key in case one
is lost. If a key is lost, consult an
Authorized Mazda Dealer as soon as
possible.
 


y If you lose a key, an Authorized Mazda
Dealer will reset the electronic codes of
your remaining keys and immobilizer
system. Bring all the remaining keys to
an Authorized Mazda Dealer to reset.
  Starting the vehicle with a key that has
not been reset is not possible.

Operation
N O T E
 


y The engine may not start and security
indicator light may illuminate or À ash
if the key is placed in an area where it
is dif¿ cult for the system to detect the
signal, such as on the dashboard. Move
the key to a location within the signal
range, switch the ignition off, and then
restart the engine.
 


y Signals from a TV or radio station, or
from a transceiver or mobile telephone
could interfere with your immobilizer
system. If you are using the proper key
and the engine fails to start, check the
security indicator light.

Arming
The system is armed when the ignition is
switched from ON to off.
The security indicator light in the
instrument cluster À ashes every 2 seconds
until the system is disarmed.



Disarming
The system is disarmed when the
ignition is switched ON with the correct
programmed key. The security indicator
light illuminates for about 3 seconds and
then turns off. If the engine does not start
with the correct key, and the security
indicator light remains illuminated or
À ashing, try the following:
Make sure the key is within the
operational range for signal transmission.
Switch the ignition off, and then restart the
engine. If the engine does not start after
3 or more tries, contact an Authorized
Mazda Dealer.
N O T E
 


y If the security indicator light À ashes
continuously while you are driving,
do not shut off the engine. Go to an
Authorized Mazda Dealer and have it
checked. If the engine is shut off while
the indicator light is À ashing, you will
not be able to restart it.
 


y Because the electronic codes are
reset when the immobilizer system
is repaired, the keys are needed.
Make sure to bring all the keys to an
Authorized Mazda Dealer so that they
can be programmed.

/:A(4'#,A'FKVKQPKPFD/:A(4'#,A'FKVKQPKPFD

3–49
Before Driving
Security System
*Some models.
Theft-Deterrent System *
If the theft-deterrent system detects an
inappropriate entry into the vehicle,
which could result in the vehicle or its
contents being stolen, the alarm alerts the
surrounding area of an abnormality by
sounding the horn and À ashing the hazard
warning lights.

The system will not function unless it's
properly armed. So when you leave the
vehicle, follow the arming procedure
correctly.
Operation
System triggering conditions
The horn sounds intermittently and the
hazard warning lights À ash for about 30
seconds when the system is triggered by
any one of the following:
 


y Unlocking a door with the key, door
lock switch, or an inside door-lock knob.
 


y Forcing open a door, the hood or the
trunk lid.
 


y Opening the hood by operating the hood
release handle.
 


y Switching the ignition ON without using
the push button start.

If the system is triggered again, the lights
and horn will activate until the driver's
door is unlocked with the transmitter.
(With the advanced keyless function)
The lights and horn can also be
deactivated by pressing the request switch
on a door.
N O T E
 


y The trunk lid does not open while the
theft-deterrent system is operating.
 


y If the battery goes dead while the theft-
deterrent system is armed, the horn will
activate and the hazard warning lights
will À ash when the battery is charged or
replaced.

How to Arm the System
1. Close the windows and the convertible
top securely.
2. Switch the ignition OFF.
3. Make sure the hood, the doors, and the
trunk lid are closed.
4. Press the lock button on the transmitter
or lock the driver's door from the
outside with the auxiliary key.
The hazard warning lights will À ash
once.
The following method will also arm the
theft-deterrent system:
Press the door-lock switch “
” while
any door is open and then close both of
the doors.
(With the advanced keyless function)
Press a request switch.

The security indicator light in the
instrument cluster À ashes twice per
second for 20 seconds.


5. After 20 seconds, the system is fully
armed.

/:A(4'#,A'FKVKQPKPFD/:A(4'#,A'FKVKQPKPFD

3–50
Before Driving
Security System
N O T E
 


y The theft-deterrent system can also be
armed by activating the auto relock
function with both the doors, the trunk
lid and the hood closed.
  Refer to Transmitter on page 3-4 .



y The system will disarm if one of the
following operations takes place within
20 seconds after pressing the lock
button:
 


y Unlocking any door.



y Opening any door.



y Opening the hood.



y Switching the ignition ON. 
 To rearm the system, do the arming
procedure again.
 


y When the doors are locked by pressing
the lock button on the transmitter
or using the auxiliary key while the
theft-deterrent system is armed, the
hazard warning lights will À ash once to
indicate that the system is armed.

To Turn Off an Armed System
An armed system can be turned off using
any one of the following methods:
 


y Pressing the unlock button on the
transmitter.
 


y Starting the engine with the push button
start.
 


y (With the advanced keyless function) 


y
 Pressing a request switch on the doors.

The hazard warning lights will À ash twice.
N O T E
When the doors are unlocked by pressing
the unlock button on the transmitter while
the theft-deterrent system is turned off, the
hazard warning lights will À ash twice to
indicate that the system is turned off.

To Stop the Alarm
A triggered alarm can be turned off using
any one of the following methods:
 


y Pressing the unlock button on the
transmitter.
 


y Starting the engine with the push button
start.
 


y (With the advanced keyless function) 


y
 Pressing a request switch on the doors.


y
 Pressing the electric trunk lid opener
while the key is being carried.


The hazard warning lights will À ash twice.
Theft-Deterrent Labels

A label indicating that your vehicle is
equipped with a Theft-Deterrent System is
in the console box.

Mazda recommends that you af¿ x it to the
lower rear corner of a front door window.
/:A(4'#,A'FKVKQPKPFD/:A(4'#,A'FKVKQPKPFD

4–4
When Driving
Start/Stop Engine
Ignition Switch
Push Button Start Positions
The system operates only when the key is
within operational range.
Each time the push button start is pressed,
the ignition switches in the order of off,
ACC, and ON. Pressing the push button
start again from ON switches the ignition
off.

Indicator light

N O T E
 


y The engine starts by pressing the push
button start while depressing the clutch
pedal (manual transmission) or the
brake pedal (automatic transmission).
To switch the ignition position, press the
push button start without depressing the
pedal.
 


y Do not leave the ignition switched
ON while the engine is not running.
Doing so could result in the battery
going dead. If the ignition is left in
ACC (For automatic transmission, the
selector lever is in the P position, and
the ignition is in ACC), the ignition
switches off automatically after about
25 minutes.

O f f
The power supply to electrical devices
turns off and the push button start indicator
light (amber) also turns off.
In this position the steering wheel is
locked.
WARNING
Before leaving the driver's seat, always
switch the ignition off , set the parking
brake, and make sure the selector lever
is in P (automatic transmission) or in 1st
gear or R (manual transmission):
Leaving the driver's seat without
switching the ignition off , setting the
parking brake, and shifting the selector
lever to P (automatic transmission) or
to 1st gear or R (manual transmission)
is dangerous. Unexpected vehicle
movement could occur which could
result in an accident.
In addition, if your intention is to leave
the vehicle for even a short period, it
is important to switch the ignition off ,
as leaving it in another position will
disable some of the vehicle's security
systems and run the battery down.

ACC (Accessory)
Some electrical accessories will operate
and the indicator light (amber) illuminates.
N O T E
The keyless entry system does not function
while the push button start has been
pressed to ACC, and the doors will not
lock/unlock even if they have been locked
manually.

/:A(4'#,A'FKVKQPKPFD/:A(4'#,A'FKVKQPKPFD

4–5
When Driving
Start/Stop Engine
O N
This is the normal running position after
the engine is started. The indicator light
(amber) turns off. (The indicator light
(amber) illuminates when the ignition
is switched ON and the engine is not
running.)
Some indicator lights/warning lights
should be inspected before the engine is
started (page 4-18 ).
N O T E
When the push button start is pressed to
ON, the sound of the fuel pump motor
operating near the fuel tank can be heard.
This does not indicate an abnormality.

Starting the Engine
WARNING
Radio waves from the key may aff ect
medical devices such as pacemakers:
Before using the key near people who
use medical devices, ask the medical
device manufacturer or your physician
if radio waves from the key will aff ect
the device.

N O T E
 


y The key must be carried because the key
carries an immobilizer chip that must
communicate with the engine controls at
short range.
 


y The engine can be started when the
push button start is pressed from off,
ACC, or ON.
 


y The push button start system functions
(function which can start the engine
by only carrying the key) can be
deactivated to prevent any possible
adverse effect on a user wearing a
pacemaker or other medical device. If
the system is deactivated, you will be
unable to start the engine by carrying
the key. Consult an Authorized Mazda
Dealer for details. If the push button
start system functions have been
deactivated, you can start the engine by
following the procedure indicated when
the key battery goes dead.
  Refer to Engine Start Function When
Key Battery is Dead on page 4-8 .
/:A(4'#,A'FKVKQPKPFD/:A(4'#,A'FKVKQPKPFD

4–6
When Driving
Start/Stop Engine
 


y After starting a cold engine, the engine
speed increases and a whining sound
from the engine compartment can be
heard.
  This is for improved exhaust gas
puri¿ cation and does not indicate any
parts defect.
 


y Engine-starting is controlled by the
spark ignition system.
  This system meets all Canadian
Interference-Causing Equipment
Standard requirements regulating the
impulse electrical ¿ eld strength of radio
noise.

1. Make sure you are carrying the key.
2. Occupants should fasten their seat
belts.
3. Make sure the parking brake is on.
4. Continue to press the brake pedal
¿ rmly until the engine has completely
started.
5. (Manual transmission)
Continue to press the clutch pedal
¿ rmly until the engine has completely
started.
(Automatic transmission)
Put the vehicle in park (P). If you must
restart the engine while the vehicle is
moving, shift into neutral (N).
N O T E
(Manual transmission)
The starter will not operate if the clutch
pedal is not depressed suf¿ ciently.
(Automatic transmission)
The starter will not operate if the selector
lever is not in P or N and the brake pedal
is not depressed suf¿ ciently.

6. Verify that the KEY indicator light
(green) in the instrument cluster and the
push button start indicator light (green)
illuminate.


Indicator light
Push button start


KEY indicator light
(green)/ KEY
warning light (red)

N O T E
 


y If the push button start indicator light
(green) À ashes, make sure that the key is
being carried.
 


y If the push button start indicator light
(green) À ashes with the key being
carried, touch the key to the push
button start and start the engine. Refer
to Engine Start Function When Key
Battery is Dead on page 4-8 .

/:A(4'#,A'FKVKQPKPFD/:A(4'#,A'FKVKQPKPFD

4–7
When Driving
Start/Stop Engine
CAUTION
If the KEY warning light (red)
illuminates, or the push button start
indicator light (amber) fl ashes, this
could indicate a problem with the
engine starting system. This may
prevent the engine from starting or
from switching the ignition to ACC or
ON. Have your vehicle inspected at an
Authorized Mazda Dealer as soon as
possible.

N O T E
 


y Under the following conditions, the
KEY warning light (red) À ashes after
the push button start is pressed. This
informs the driver that the push button
start will not switch to ACC even if it is
pressed from off.
 


y The key battery is dead.



y The key is out of operational range.



y The key is placed in areas where it is
dif¿ cult for the system to detect the
signal (page 3-7 ).
 


y A key from another manufacturer
similar to the key is in the
operational range.

 


y (Forced engine starting method) 
 If the KEY warning light (red)
illuminates, or the push button start
indicator light (amber) À ashes, this
could indicate that the engine may not
start using the usual starting method.
Have your vehicle inspected at an
Authorized Mazda Dealer as soon as
possible. If this occurs, the engine can
be force-started. Press and hold the
push button start until the engine starts.
Other procedures necessary for starting
the engine, such as having the key in the
cabin, and depressing the clutch pedal
(manual transmission) or the brake
pedal (automatic transmission) are
required.
 


y When the engine is force-started,
the KEY warning light (red) remains
illuminated and the push button
start indicator light (amber) remains
À ashing.




y (Automatic transmission) 
 When the selector lever is in the neutral
(N) position, the KEY indicator light
(green) and the push button start
indicator light (green) do not illuminate.

7. Press the push button start after both
the KEY indicator light (green) in the
instrument cluster and the push button
start indicator light (green) illuminate.
N O T E
 


y After starting the engine, the push
button start indicator light (amber)
turns off and the ignition switches to the
ON position.
 


y After pressing the push button start and
before the engine starts, the operation
sound of the fuel pump motor from near
the fuel tank can be heard, however, this
does not indicate a malfunction.

/:A(4'#,A'FKVKQPKPFD/:A(4'#,A'FKVKQPKPFD