ignition MAZDA MODEL MX-5 RF 2017 Owners Manual (in English)

6–42
Maintenance and Care
Owner Maintenance
3. Pull the centre of each plastic retainer
and remove the retainers, and then
partially peel back the mudguard.
Removal
Installation
4. Remove the unit by pressing the tab on
the unit with your ¿ nger and pulling the
unit forward.
5. Detach the electrical connector from
the unit by pulling it to the rear.
6. Install the new side direction indicator
unit in the reverse order of the removal
procedure.
Rear direction indicator lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Pull the centre of each plastic retainer
and remove the retainers and the boot
end trim.
Removal
Installation
3. Disconnect the connector from the unit
by pressing the tab on the connector
with your ¿ nger and pulling the
connector downward.
/:A(.'',A'FKVKQPKPFD

6–45
Maintenance and Care
Owner Maintenance
*Some models.
9. After the hook is detached, pull out
the rear combination lamp unit in the
direction of the arrow and remove it.
Grommet installation hole Clip
HookRear combination
lamp unit
CAUTION
Carefully pull out the rear combination
lamp unit when removing it from the
body.
The wiring may become damaged if the
rear combination lamp unit is forcefully
pulled out.
10. Turn the socket and bulb assembly
anticlockwise and remove it.
11. Disconnect the bulb from the socket.
12. Install the new bulb in the reverse order
of the removal procedure.
Reverse lights, Rear fog light *
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Turn the socket and bulb assembly
anticlockwise and remove it.
3. Disconnect the bulb from the socket.
4. Install the new bulb in the reverse order
of the removal procedure.
/:A(.'',A'FKVKQPKPFD

6–46
Maintenance and Care
Owner Maintenance
Number plate lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Remove the unit by pressing the tab on
the unit with your ¿ nger and pulling the
unit downward.
3. Turn the socket and bulb assembly
anticlockwise and remove it.
4. Disconnect the bulb from the socket.
5. Install the new bulb in the reverse order
of the removal procedure.
Replacing Interior Light Bulbs
Overhead light
1. Wrap a small À athead screwdriver
with a soft cloth to prevent damage to
the lens, and then remove the lens by
carefully prying on the edge of the lens
with the À athead screwdriver.
2. Disconnect the bulb by pulling it out.
3. Install the new bulb in the reverse order
of the removal procedure.
/:A(.'',A'FKVKQPKPFD

6–47
Maintenance and Care
Owner Maintenance
Boot light
1. Wrap a small À athead screwdriver
with a soft cloth to prevent damage to
the lens, and then remove the lens by
carefully prying on the edge of the lens
with the À athead screwdriver.
2. Disconnect the connector from the unit.
3. Disconnect the bulb by pulling it out.
4. Install the new bulb in the reverse order
of the removal procedure.
Fuses
Your vehicle's electrical system is
protected by fuses.
If any lights, accessories, or controls do
not work, inspect the appropriate circuit
protector. If a fuse has blown, the inside
element will be melted.
If the same fuse blows again, avoid using
that system and consult an expert repairer,
we recommend an Authorised Mazda
Repairer as soon as possible.
Fuse Replacement
Replacing the fuses on the vehicle's left
side
If the electrical system does not work, ¿ rst
inspect the fuses on the vehicle's left side.
1. Make sure the ignition is switched off,
and other switches are off.
2. Open the fuse panel cover.
/:A(.'',A'FKVKQPKPFD

6–48
Maintenance and Care
Owner Maintenance
3. Pull the fuse straight out with the
fuse puller provided on the fuse block
located in the engine compartment.
4. Inspect the fuse and replace it if it is
blown.
NormalBlown
5. Insert a new fuse of the same amperage
rating, and make sure it ¿ ts tightly. If
it does not ¿ t tightly, have an expert
install it. We recommend an Authorised
Mazda Repairer.
If you have no spare fuses, borrow one
of the same rating from a circuit not
essential to vehicle operation, such as
the AUDIO or OUTLET circuit.
CAUTION
Always replace a fuse with a genuine
Mazda fuse or equivalent of the same
rating. Otherwise you may damage the
electric system.
6. Reinstall the cover and make sure that
it is securely installed.
Replacing the fuses under the bonnet
If the headlights or other electrical
components do not work and the fuses
in the cabin are normal, inspect the fuse
block under the bonnet. If a fuse is blown,
it must be replaced. Follow these steps:
1. Make sure the ignition is switched off,
and other switches are off.
2. Remove the fuse block cover.
NOTE
If the lock is forcefully opened, the
fuse block cover may come in contact
with the frame when it is removed and
become scratched.
When removing the cover, remove
it slowly according to the following
procedure.
1. Disengage the rear lock by
pressing down on the front tab
with your ¿ ngers.
2. Remove the front tab while
slightly lifting the front of the
cover.
/:A(.'',A'FKVKQPKPFD

6–55
Maintenance and Care
Appearance Care
Maintaining the Finish
W a s h i n g
CAUTION
  When the wiper lever is in the
position and the ignition is switched
ON, the wipers may move
automatically in the following cases:
 


 If the windscreen above the rain
sensor is touched or wiped with a
cloth.
 


 If the windscreen is struck with a
hand or other object from either
outside or inside the vehicle.
  Keep hands and scrapers clear of the
windscreen when the wiper lever is
in the
position and the ignition
is switched ON as ¿ ngers could be
pinched or the wipers and wiper
blades damaged when the wipers
activate automatically.
 If you are going to clean the
windscreen, be sure the wipers are
turned off completely (when it is
most likely that the engine is left
running) this is particularly important
when clearing ice and snow.
 
 Do not spray water in the engine
compartment. Otherwise, it could
result in engine-starting problems or
damage to electrical parts.
  When washing and waxing the
vehicle, be careful not to apply
excessive force to any single area of
the vehicle bonnet. Otherwise, you
could dent the vehicle.
CAUTION
  Do not use automatic car washing
machines and car washing devices
using high water pressure.
  Make sure that the fuel À ap is closed
and lock the doors. Otherwise, the
fuelÀ ap may be forcefully opened by
water pressure causing damage to the
vehicle or fuel À ap.
To help protect the ¿ nish from rust
and deterioration, wash your Mazda
thoroughly and frequently, at least once a
month, with lukewarm or cold water.
If the vehicle is washed improperly, the
paint surface could be scratched. Here are
some examples of how scratching could
occur.
Scratches occur on the paint surface when:
 


 The vehicle is washed without ¿ rst
rinsing off dirt and other foreign matter.
 


 The vehicle is washed with a rough, dry,
or dirty cloth.
 


 The vehicle is washed at a car wash that
uses brushes that are dirty or too stiff.
 


 Cleansers or wax containing abrasives
are used.
NOTE
  Mazda is not responsible for
scratches caused by automatic car
washes or improper washing.
  Scratches are more noticeable on
vehicles with darker paint ¿ nishes.
/:A(.'',A'FKVKQPKPFD

6–62
Maintenance and Care
Appearance Care
NOTE
If leaves or other foreign matter block
the drainage outlets, water may enter the
cabin. Clean the drainage outlets at least
once a year.
1. Continue pressing the retractable
fastback switch in the open direction
until the rear roof is raised up from the
fully closed position.
Refer to Opening the Roof on page
3-51 .
2. Remove your ¿ nger from the
retractable fastback switch after the
rear roof is raised up.
3. Make sure the drainage outlets are
visible.
Drainage
outlet
Rear roof links
4. Switch the ignition OFF.
WARNING
Verify that the ignition is switched off:
Closing the roof with the ignition not
switched off is dangerous as the motors
could turn on suddenly and cause
injury resulting from hands or ¿ ngers
being pinched in the mechanism.
5. Remove leaves and other foreign
matter accumulated in the drainage
outlet.
CAUTION
When cleaning the drainage outlets, be
careful not to touch the roof links or the
framework of the rear roof. Otherwise,
you could get injured.
Roof links Rear roof
/:A(.'',A'FKVKQPKPFD

7–3
If Trouble Arises
Flat Tyre
*Some models.
F l a t T y r e *
Either run-À at tyres or conventional tyres
are equipped on your Mazda depending on
the speci¿ cation, therefore the procedure
for repairing a À at tyre differs depending
on the type of tyre. Before driving, make
sure which type of tyre is equipped on
your Mazda. If you cannot identify your
tyre type, consult an expert repairer,
we recommend an Authorised Mazda
Repairer.
How to Identify Your Tyre Type
R u n -À at tyre
A run-À at tyre has a
and/or
indication on the side wall.
and/or
Conventional tyre
A conventional tyre does not have a
and/or indication on the side wall.
Vehicle with Run-À at Tyres
WARNING
Have the tyres checked or perform the
appropriate repair as soon as possible
by an expert repairer, we recommend
an Authorised Mazda Repairer:
When the À at tyre warning light
illuminates or the tyre pressure
warning beep sound is heard, it is
dangerous to drive the vehicle at
high speeds, or perform sudden
manoeuvring or braking. Vehicle
drivability could worsen and result in
an accident.
When the À at tyre warning light
illuminates or the tyre pressure
warning beep sound is heard, decrease
vehicle speed immediately and avoid
sudden manoeuvring and braking.
If a run-À at tyre is punctured, the FLAT
TIRE warning light illuminates in the
instrument cluster, and a beep sound is
heard for about 30 seconds.
NOTE
Until the À at tyre is changed, the beep
sound is heard for about 30 seconds
every time the ignition is switched ON.
/:A(.'',A'FKVKQPKPFD

7–11
If Trouble Arises
Flat Tyre
WARNING
Do not adhere the speed restriction
sticker to the padded area on the
steering wheel:
Adhering the speed restriction sticker
to the padded area on the steering
wheel is dangerous because the air
bag may not operate (deploy) normally
resulting in serious injury. In addition,
do not adhere the sticker to areas where
warning lights or the speedometer
cannot be viewed.
16. Pull out the air compressor hose and
the air compressor plug from the air
compressor.
Compressor hose
17. Install the air compressor hose to the
tyre valve.
Valve
Compressor hose
18. Insert the air compressor plug into the
accessory socket inside the vehicle and
switch the ignition to ACC.
Refer to Accessory Sockets on page
5-125 .
Compressor
Compressor plug
CAUTION
When inserting the air compressor
plug into or removing it from the
accessory socket, make sure that the air
compressor switch is off. When turning
the air compressor on/off, use the air
compressor switch.
19. Turn the air compressor switch on and
inÀ ate the tyre carefully to the correct
inÀ ation pressure.
/:A(.'',A'FKVKQPKPFD

7–21
If Trouble Arises
Battery Runs Out
CAUTION
Use only a 12 V booster system. You can damage a 12 V starter, ignition system, and other
electrical parts beyond repair with a 24 V power supply (two 12 V batteries in series or a
24 V motor generator set).
Jumper leads
Booster batteryDischarged battery
/:A(.'',A'FKVKQPKPFD