child restraint MAZDA MODEL MX-5 RF 2017 (in English) User Guide

Page 43 of 609

2–23
Essential Safety Equipment
Child Restraint
WARNING
Always install a baby seat in the correct
seat position:
Installing a baby seat without ¿ rst
consulting the table “Child-Restraint
System Suitability for Various Seat
Positions” is dangerous. A baby seat
installed on the wrong seat position
cannot be properly secured. In a
collision, the child could hit something
or someone in the vehicle and be
seriously injured or even killed.
Never use a rear-facing child-restraint
system on the passenger seat protected
by an air bag:
Extreme Hazard! Do not use a
rearward facing child restraint on a
seat protected by an airbag in front of
it!
The child-restraint system can be hit
by the deploying air bag and knocked
out of position. A child in the child-
restraint system could be seriously
injured or killed. If your vehicle is
equipped with a passenger occupant,
always make sure the passenger air
bag deactivation OFF indicator light is
illuminated, if installing a rear-facing
child-restraint system on the passenger
seat is unavoidable.
Child Seat Installation Position
A child seat is used in front-facing and
rear-facing positions depending on the
age and size of the child. When installing,
follow the manufacturer's instructions in
accordance with the appropriate age and
size of the child as well as the directions
for installing the child-restraint system.
Refer to the table, “Child-Restraint System
Suitability for Various Seat Positions”
for child seat installation position (page
2-26 ).
Rear-facing type
WARNING
Always install a rear-facing child seat
in the correct seat position:
Installing a rear-facing child seat
without¿ rst consulting the table
“Child-Restraint System Suitability for
Various Seat Positions” is dangerous.
A rear-facing child seat installed on the
wrong seat position cannot be properly
secured. In a collision, the child could
hit something or someone in the vehicle
and be seriously injured or even killed.
/:A(.'',A'FKVKQPKPFD

Page 44 of 609

2–24
Essential Safety Equipment
Child Restraint
WARNING
Never use a rear-facing child-restraint
system on the passenger seat protected
by an air bag:
NEVER use a rearward facing child
restraint on a seat protected by an
ACTIVE AIRBAG in front of it,
DEATH or SERIOUS INJURY to the
CHILD can occur.
The child-restraint system can be hit
by the deploying air bag and knocked
out of position. A child in the child-
restraint system could be seriously
injured or killed. If your vehicle is
equipped with a passenger occupant
classi¿ cation system, always make
sure the passenger air bag deactivation
OFF indicator light is illuminated, if
installing a rear-facing child-restraint
system on the passenger seat is
unavoidable.
Front-facing type
WARNING
Never install a front-facing child seat
in the wrong seat position:
Installing a front-facing child seat
without¿ rst consulting the table
“Child-Restraint System Suitability for
Various Seat Positions” is dangerous. A
front-facing child seat installed in the
wrong seat position cannot be properly
secured. In a collision, the child could
hit something or someone in the vehicle
and be seriously injured or even killed.
Make sure the passenger air bag
deactivation OFF indicator light is
illuminated.
Before installing child-restraint
system on the passenger seat, move the
passenger seat as far back as possible:
In a collision, the force of a deploying
air bag could cause serious injury or
death to the child.
Make sure the passenger air bag
deactivation OFF indicator light is
illuminated.
/:A(.'',A'FKVKQPKPFD

Page 45 of 609

2–25
Essential Safety Equipment
Child Restraint
Junior Seat Installation Position
A junior seat is used in the front-facing
position only.
Refer to the table, “Child-Restraint System
Suitability for Various Seat Positions”
for junior seat installation position (page
2-26 ).
WARNING
Always install a junior seat in the
correct seat position:
Installing a junior seat without ¿ rst
consulting the table “Child-Restraint
System Suitability for Various Seat
Positions” is dangerous. A junior seat
installed on the wrong seat position
cannot be properly secured. In a
collision, the child could hit something
or someone in the vehicle and be
seriously injured or even killed.
Before installing child-restraint
system on the passenger seat, move the
passenger seat as far back as possible:
*1
In a collision, the force of a deploying
air bag could cause serious injury or
death to the child.
Make sure the passenger air bag
deactivation OFF indicator light is
illuminated.
*1 The rearmost position may not be
suitable for the installation of some
child-restraint systems.
/:A(.'',A'FKVKQPKPFD

Page 46 of 609

2–26
Essential Safety Equipment
Child Restraint
Child-Restraint System Suitability for Various Seat
Positions Table
(Europe and countries conforming to the UNECE 16 regulation)
Provided information in the table shows your child-restraint system suitability for various
seating position. For installation suitability of other manufacturer child-restraint system,
carefully consult the manufacturer's instructions which accompany the child-restraint
system.
ISOFIX anchor-secured child-restraint systems
When installing a child-restraint system to the passenger seat, refer to the child-restraint
system manufacturer's instructions and the Using ISOFIX Anchor on page 2-30 .
Mass group Size Class Fixture Seat Positions
Vehicle ISOFIX positions
Passenger seat
Carrycot F ISO/L1 X
G ISO/L2 X
(1) X
GROUP 0
Up to 10 kg (less than 22 lb) E ISO/R1 X
(1) X
GROUP 0
Up to 13 kg (less than 29 lb) E ISO/R1 IL
*1
D ISO/R2 X
C ISO/R3 X
(1) X
GROUP 1
9 kg — 18 kg (20 lb — 40 lb) D ISO/R2 X
C ISO/R3 X
B ISO/F2 IUF
B1 ISO/F2X IUF
A ISO/F3 X
(1) IL
*2
GROUP 2
15 kg — 25 kg (33 lb — 55 lb) (1) IL *3
GROUP 3
22 kg — 36 kg (48 lb — 79 lb) (1) IL *3
(1) For the CRS which do not carry the ISO/XX size class identi¿ cation (A to G), for the applicable mass group,
the car manufacturer shall indicate the vehicle speci¿ c ISOFIX child-restraint system(s) recommended for each
position.
Key of letters to be inserted in the above table:
IUF = Suitable for ISOFIX forward child-restraints systems of universal category approved for use in this mass
group.
IL = Suitable for particular ISOFIX child-restraint systems (CRS) given in the attached list.
These ISOFIX CRS are those of the “speci¿ c vehicle”, “restricted” or “semi-universal” categories.
*1 A CabrioFix child-restraint attached to an EasyFix Base, both sold by MAXI-COSI
® , can be installed.
/:A(.'',A'FKVKQPKPFD

Page 47 of 609

2–27
Essential Safety Equipment
Child Restraint
*2 A Pearl child-restraint attached to an FamilyFix Base, both sold by MAXI-COSI ® , can be installed.
*3 BRITAX RÖMER ® KIDFIX can be installed. (KIDFIX is no longer in production)
X = ISOFIX position not suitable for ISOFIX child-restraint systems in this mass group and/or this size class.
(Except Europe)
Regarding child-restraint systems which can be installed to your Mazda, consult an expert repairer, we recommend
an Authorised Mazda Repairer.
i-Size child-restraint systems
An i-Size child-restraint system can be installed to the speci¿ ed seat as follows:
Passenger seat
i-Size child-restraint systems X
Key of letters to be inserted in the above table:
X = Seating position not suitable for i-Size “universal” child-restraint systems.
NOTE
An i-Size child-restraint system refers to a child-restraint system which has acquired
i-Size category certi¿ cation for the UNECE 129 regulation.
/:A(.'',A'FKVKQPKPFD

Page 48 of 609

2–28
Essential Safety Equipment
Child Restraint
Seat belt-secured child-restraint systems
System
group Age group Weight group Child-
restraint
system
type Passenger seat
Without a
passenger
occupant
classi¿ cation
system With a passenger occupant
classi¿ cation system
(Air bag
enabled) (Air bag
disabled)
GROUP 0 Up to
approximately
9 months old Less than 10 kg
(less than 22 lb) Baby seat X X U
GROUP 0
Up to
approximately
2 years old Less than 13 kg
(less than 29 lb) Baby seat X X U
GROUP 1 Approximately
8 months to 4
years old 9 kg — 18 kg
(20 lb — 40 lb) Child seat L UF U
GROUP 2 Approximately
3 to 7 years old 15 kg— 25 kg
(33 lb — 55 lb) Junior seat L UF U
GROUP 3 Approximately
6 to 12 years
old 22 kg — 36 kg
(48 lb — 79 lb) Junior seat L UF U
Key of letters to be inserted in the above table:
U = Suitable for “universal” category restraints approved for use in this mass group.
UF = Suitable for forward-facing “universal” category restraints approved for use in this mass group.
L = For the child restraint systems categorized in this weight group, consult an expert repairer, we recommend an
Authorised Mazda Repairer.
Regarding child-restraint systems which can be installed, refer to the accessories catalog.
X = Seat position not suitable for children in this mass group.
(Refer to the “Accessories Catalog” for installing a Mazda genuine child-restraint system.)
/:A(.'',A'FKVKQPKPFD

Page 49 of 609

2–29
Essential Safety Equipment
Child Restraint
Installing Child-Restraint
Systems
Anchor Bracket
Anchor brackets for securing child-
restraint systems are equipped in the
vehicle. Locate anchor position using the
illustration.
To install a child-restraint system,
always follow the instruction manual
accompanying the child-restraint system.
Anchor bracket location
Use the indicated anchor bracket locations
when installing a child-restraint system
equipped with a tether.
Anchor bracket
WARNING
Always attach the tether strap to the
correct tether anchor position:
Attaching the tether strap to the
incorrect tether anchor position is
dangerous. In a collision, the tether
strap could come off and loosen the
child-restraint system. If the child-
restraint system moves it could result in
death or injury to the child.
Always route the tether strap between
the head restraint and the seatback:
Routing the tether strap on top of
the head restraint is dangerous. In a
collision the tether strap could slide off
the head restraint and loosen the child-
restraint system. The child-restraint
system could move which may result in
death or injury to the child.
CAUTION
When moving the seats forward and
rearward, make sure you hold onto
the seatback with your hand while
operating. If the seatback is not held, the
seat will move suddenly and could cause
injury.
1. Open the convertible top.
2. Slide the passenger seat as far back as
possible and then slide it forward about
10 notches (100 mm) so that your hand
can be placed behind it (page 2-5 ).
/:A(.'',A'FKVKQPKPFD

Page 50 of 609

2–30
Essential Safety Equipment
Child Restraint
*Some models.
3. Remove the cover.
NOTE
Be careful not to lost the removed cover.
4. Place the child-restraint on the
passenger seat.
5. Pass the tether strap under the head
restraint and install it to the tether
anchor.
For the tether strap adjustment
method, refer to the child-restraint seat
manufacturer’s instructions.
Using the Seat Belt
CAUTION
When moving the seats forward and
rearward, make sure you hold onto
the seatback with your hand while
operating. If the seatback is not held, the
seat will move suddenly and could cause
injury.
When installing a child-restraint system,
follow the installation instructions
included with the product.
Also, open the convertible top and slide
the seat as far back as possible, fold down
the seatback as far as possible.
Using ISOFIX Anchor *
WARNING
Follow the manufacturer's instructions
for the use of the child-restraint
system:
An unsecured child-restraint system
is dangerous. In a sudden stop or a
collision it could move causing serious
injury or death to the child or other
occupants. Make sure any child-
restraint system is properly secured in
place according to the manufacturer's
instructions.
/:A(.'',A'FKVKQPKPFD

Page 51 of 609

2–31
Essential Safety Equipment
Child Restraint
WARNING
Make sure the child-restraint system is
properly secured:
A child-restraint system that is not
secured is dangerous. In a sudden stop
or collision, it can become a projectile
and hit someone, causing serious
injury. When not in use, remove it from
the vehicle, put it in the boot or at least
make sure it is securely fastened to the
ISOFIX anchors.
Make sure there are no seat belts or
foreign objects near or around the
ISOFIX anchor-secured child-restraint
system:
Not following the child-restraint system
manufacturer's instructions when
installing the child-restraint system is
dangerous. If seat belts or a foreign
object prevent the child-restraint
system from being securely attached
to the ISOFIX anchors and the child-
restraint system is installed improperly,
the child-restraint system could move
in a sudden stop or collision causing
serious injury or death to the child or
other occupants. When installing the
child-restraint system, make sure there
are no seat belts or foreign objects
near or around the ISOFIX anchors.
Always follow the child-restraint system
manufacturer's instructions.
CAUTION
When moving the seats forward and
rearward, make sure you hold onto
the seatback with your hand while
operating. If the seatback is not held, the
seat will move suddenly and could cause
injury.
1. Open the convertible top.
2. Make sure the ignition is switched off.
3. Slide the passenger seat as far back as
possible (page 2-5 ).
*1
*1 You may need to move the seat
forward slightly and recline the
back of the seat, in order to assist in
the¿ tment of some child-restraint
systems.
4 . Make sure the seatback is securely
latched by pushing it back until it is
fully locked.
5 . Expand the area between the seat
bottom and the seatback slightly to
verify the locations of the ISOFIX
anchor.
/:A(.'',A'FKVKQPKPFD

Page 52 of 609

2–32
Essential Safety Equipment
Child Restraint
NOTE
The markings above the ISOFIX
anchors indicate the locations of the
ISOFIX anchors for the attachment of a
child-restraint system.
6 . Secure the child-restraint system using
the ISOFIX anchor, following the
child-restraint system manufacturer's
instruction.
7 . Switch the ignition ON and make sure
the passenger air bag deactivation
OFF indicator light illuminates after
installing a child-restraint system on
the passenger seat.
If the passenger air bag deactivation
OFF indicator light does not illuminate,
remove the child-restraint system,
switch the ignition to OFF, and then re-
install the child-restraint system (page
2-47 ).
8 . If your child-restraint system came
equipped with a tether, that probably
means it is very important to properly
secure the tether for child safety. Please
carefully follow the child-restraint
system manufacturer's instructions
when installing tethers (page 2-29 ).
WARNING
Always attach the tether strap to the
correct tether anchor position:
Attaching the tether strap to the
incorrect tether anchor position is
dangerous. In a collision, the tether
strap could come off and loosen the
child-restraint system. If the child-
restraint system moves it could result in
death or injury to the child.
Always route the tether strap between
the head restraint and the seatback:
Routing the tether strap on top of
the head restraint is dangerous. In a
collision the tether strap could slide off
the head restraint and loosen the child-
restraint system. The child-restraint
system could move which may result in
death or injury to the child.
/:A(.'',A'FKVKQPKPFD

Page:   < prev 1-10 11-20 21-30 next >