height MAZDA MODEL PROTÉGÉ 2002 Owners Manual (in English)

2-4
Essential Safety Equipment
Seats
Form No. 8Q36-EA-01F

Seat Tilt (Driver’s Seat)
The seat-bottom angle can be adjusted by
rotating the dial.

Head Restraint
Height adjustment
To raise a head restraint, pull it up to the
desired position.
To lower the head restraint, press the
stop-catch release, then push the head
restraint down.
Adjust the head restraint so that the top
parallels the top of the passenger’s ears,
never the passenger’s neck.
Up
Down
Dial
Front of seat bottom
Up
Down
DialRear of seat bottom
Head Restraints Adjustment:
Driving with the head restraints
adjusted too low or removed is
dangerous. With no support behind
your head, your neck could be
seriously injured in a collision.
Always drive with the head restraints
inserted when seats are being used
and make sure they are properly
adjusted.
WARNING
Stop-catch release
J39L(02MY).book Page 4 Thursday, November 1, 2001 10:49 AM

2-10
Essential Safety Equipment
Seats
Form No. 8Q36-EA-01F
Height adjustment
To raise a head restraint, pull it up to the
desired position.
To lower the head restraint, press the
stop-catch release, then push the head
restraint down.
Adjust the head restraint so that the top
parallels the top of the passenger’s ears,
never the passenger’s neck.
Removal
To remove the head restraint, press the
stop-catch release, then pull up on the
head restraint.
Stop-catch release
Stop-catch release
J39L(02MY).book Page 10 Thursday, November 1, 2001 10:49 AM

2-15
Essential Safety Equipment
Seat Belt Systems
Form No. 8Q36-EA-01F

Unfastening the Seat Belts
Depress the button on the buckle.

Shoulder Belt Adjuster
Adjust the height of the shoulder belt if
the seat belt touches your neck, or if it
crosses your arm instead of your shoulder.
To raise the shoulder belt adjuster, push
the adjuster up. To lower the shoulder belt
adjuster, push the button and slide it
down. Make sure the adjuster is locked.
NOTE
If a belt does not fully retract, inspect it
for kinks and twists.
Positioning the Shoulder Portion of
the Seat Belt:
Improper positioning of the shoulder
portion of the seat belt is dangerous.
An improperly positioned belt will
provide little or no protection in a
collision. Always make sure the
shoulder portion of the seat belt is
positioned across your shoulder and
near your neck, but never under your
arm, on your neck, or on your upper
arm.
Button
Shoulder belt
adjuster
WARNING
J39L(02MY).book Page 15 Thursday, November 1, 2001 10:49 AM

2-38
Essential Safety Equipment
SRS Air Bags
Form No. 8Q36-EA-01F
Installation of Front-End Equipment:
Installation of front-end equipment, such as frontal protection bar (kangaroo bar,
bull bar, push bar, etc.), snowplow, or winches, is dangerous. The air bag crash
sensor system could be affected. This could cause air bags to inflate unexpectedly, or
it could prevent the air bags from inflating during an accident. Front occupants could
be seriously injured. Never install any front-end equipment to your vehicle.
Suspension Adjustment:
Adjusting the vehicle suspension is dangerous. If the vehicle’s height or the
suspension is changed, the vehicle will be unable to accurately detect a collision
resulting in incorrect or unexpected air bag deployment and the possibility of serious
injuries.
Modification of the Supplemental Restraint System:
Modifying the components or wiring of the supplemental restraint system is
dangerous. You could accidentally activate it or make it inoperable. Don’t make any
modifications to the supplemental restraint system. This includes installing trim,
badges, or anything else over the air bag storage areas. It also includes installing
extra electric equipment on or near system components or wiring. An Authorized
Mazda Dealer can provide the special care needed in the removal and installation of
front seats. It is important to protect the side air bag wiring and connections to assure
that the bags do not accidentally deploy and that the seats retain an undamaged air
bag connection.
Using Seat Covers:
Using a seat cover on the front seats is dangerous. In a severe side collision, the seat
covers could interfere with the side air bag inflation and serious injuries could result.
Never use seat covers on the front seats.
WARNING
J39L(02MY).book Page 38 Thursday, November 1, 2001 10:49 AM

3-22
Knowing Your Mazda
Doors and Locks
Form No. 8Q36-EA-01F

Roof Rack Adjustment
1. Loosen the screw at both ends of the
rear cross bar, then remove the rear
cross bar covers.
2. Loosen the bolt at both ends of the rear
cross bar, then slide the rear cross bar
to the desired position. •The roof rack is not designed for
direct placement of objects or loads.
A special attachment kit is
necessary. Consult an Authorized
Mazda Dealer.
•The maximum load on the roof rack
is 75 kg (165 lb). Do not overload.
•Because the bolts and screws may
loosen initially, retighten them.
Periodically check bolts for
looseness approximately every 100
km (62 miles).
•Avoid turning sharply and jamming
on the brakes while the roof rack
installed. Doing so may cause an
accident or the luggage may fall off.
•Road conditions (especially steep
curves or rough roads) and weather
changes (strong cross wind, head
wind, rain, snow, or fog) can change
vehicle operating characteristics
greatly when the vehicle is
equipped with the roof rack. To
cope with these conditions, drive at
a slower speed.
•When driving in a tunnel or parking
garage or any place with height
restrictions with the roof rack
installed, be aware that the roof rack
will raise the total clearance of the
vehicle.
•If the vehicle is washed in an
automatic car wash with the roof
rack installed, the roof rack or the
roof of the vehicle can be damaged.
Before washing the vehicle in an
automatic car wash, always remove
the roof rack.CAUTION
Screw
Rear cross bar coverRear cross bar
Bolt
J39L(02MY).book Page 22 Thursday, November 1, 2001 10:49 AM

8-29
Maintenance and Care
Owner Maintenance
Form No. 8Q36-EA-01F

Temporary Spare Tire
Inspect the temporary spare tire at least
monthly to make sure it’s properly
inflated and stored.
The temporary spare tire is easier to
handle because of its construction. It is
lighter and smaller than a conventional
tire and should be used only for an
emergency and only for a short distance.
Use the temporary only until the
conventional tire is repaired, which should
be as soon as possible.
Maintain its pressure at 420 kPa (60 psi).

Replacing a Wheel
When replacing a wheel, make sure the
new one is the same as the original factory
wheel in diameter, rim width, and offset.
Proper tire balancing provides the best
riding comfort and helps reduce tread
wear. Out-of-balance tires can cause
vibration and uneven wear, such as
cupping and flat spots.
•Don’t use your temporary spare tire
rim with a snow tire or a
conventional tire. Neither will
properly fit and could damage both
tire and rim.
•The temporary spare tire has a tread
life of up to 5,000 km (3,000 miles),
depending on road conditions and
driving habits.
•When the tread wear solid-band
indicator appears, replace the tire
with the same type of temporary
spare.
CAUTION
Using a Wrong-Sized Wheel:
Using a wrong-sized wheel is
dangerous. Braking and handling
could be affected, leading to loss of
control and an accident. Always use
wheels of the correct size on your
vehicle.
A wrong-sized wheel may adversely
affect
•Tire fit
•Wheel and bearing life
•Ground clearance
•Snow-chain clearance
•Speedometer calibration
•Headlight aim
•Bumper height
WARNING
CAUTION
J39L(02MY).book Page 29 Thursday, November 1, 2001 10:49 AM

10-5
Specifications
Form No. 8Q36-EA-01F

Capacities
(Approximate Quantities)
Check oil and fluid levels with dipsticks or reservoir gauges.

Dimensions
ItemUnit
L US qt Imp qt
Engine oil1.6-liter engineWith oil filter replacement 3.2 3.4 2.8
Without oil filter
replacement3.0 3.2 2.6
1.8 and 2.0-liter
enginesWith oil filter replacement 3.5 3.7 3.1
Without oil filter
replacement3.3 3.5 2.9
Coolant1.6-liter engineWith heater 6.0 6.3 5.3
Without heater 5.5 5.8 4.8
1.8 and 2.0-liter
enginesWith heater 7.5 7.9 6.6
Without heater 6.9 7.3 6.1
Transaxle oilManual transaxle 2.7 2.9 2.4
Automatic transaxle 7.2 7.6 6.3
Fuel tank1.6-liter engine 50 13.2 (US gal) 11.0 (Imp gal)
1.8 and 2.0-liter engines 55 14.5 (US gal) 12.1 (Imp gal)
ItemModel
Sedan Hatchback
Overall length 4,450 mm (175.2 in) 4,331 mm (170.5 in)
Overall width 1,705 mm (67.1 in) 1,705 mm (67.1 in)
Overall height 1,410 mm (55.5 in) 1,410 mm (55.5 in)
Front tread 1,470 mm (57.9 in) 1,465 mm (57.7 in)
Rear tread 1,470 mm (57.9 in) 1,470 mm (57.9 in)
Wheelbase 2,610 mm (102.8 in) 2,610 mm (102.8 in)
J39L(02MY).book Page 5 Thursday, November 1, 2001 10:49 AM