MERCEDES-BENZ C-Class 2008 W204 Comand Manual

10 Introduction
Operating safety
! NOTE: This equipment has been tested and
found to comply with the limits for a Class A dig-
ital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference when
the equipment is operated in a commercial envi-
ronment. This equipment generates, uses and
can radiate radio frequency energy and, if not in-
stalled and used in accordance with the instruc-
tion manual, may cause harmful interference to
radio communications.G Warning
Change or modification not expressly ap-
proved by the party responsible for compli-
ance could void the user's authority to
operate this equipment.
G Warning
This transmitter must not be co-located or
operated in conjunction with any other an-
tenna or tranmitter.
G Warning
This equipment complies with FCC radiation
exposure limits set forth for uncontrolled
equipment and meets the FCC radio fre-
quency (RF) Exposure Guidelines in Supple-
ment C to OET65.
This equipment has very low levels of RF en-
ergy that is deemed to comply without max-
imum permissive exposure evaluation
(MPE). But it is desirable that it should be in-
stalled and operated with at least 8 inches
(20 cm) and more between the radiator and
person's body (excluding extremities:
hands, wrists feet and legs.)

11 Introduction
Operating safety
DaimlerChrysler declares herewith that
this device conforms to the basic
requirements and the other relevant
regulations of Directive 1999/5/EC (RTTE
Directive).
Please bear the following information in
mind when using the COMAND:

The safety instructions in this guide

Road Traffic Regulations
i Tampering with electronic components or
systems (e.g. radio, DVD changer) and their soft-
ware may result in malfunctioning. Systems
which have not been changed may be affected
due to the connectivity of the electronics.
Malfunctions of the electronics can seriously en-
danger the operational safety of your vehicle.
i Always have all work or modifications to
electronic components carried out by a qualified
specialist workshop with the necessary exper-
tise and tools for any work required.
DaimlerChrysler recommends a Mercedes-Benz
Service centre for this purpose.
Especially for safety-related operations and op-
erations on safety-related systems, servicing by
a qualified specialist workshop is essential.
For safety reasons, some COMAND func-
tions are restricted or not available when
the vehicle is moving. This can be recog-
nized, for example, from the fact that cer-
tain menu items cannot be selected or the
COMAND displays a corresponding mes-
sage.
Declaration of conformity regarding
the distribution of telecommunica-
tions equipment
Intended purpose
Function restrictions when driving
the vehicle

12

13 At a glance
COMAND control system . . . . . . . 14
Multifunction steering wheel . . . 23
Operating COMAND . . . . . . . . . . . 31
Basic functions of COMAND . . . . 35

14 At a glance
COMAND control system
COMAND comprises

the COMAND display

the COMAND control unit with DVD
changer

the COMAND controller with the Back
and Clear button
With COMAND you can operate the follow-
ing main functions:

the navigation system

the audio function with the
radio, SatRadio*, disc (CD audio, DVD
audio or MP3 mode),
PCMCIA memory card (MP3 mode),
Music Register and Audio Aux operat-
ing modes

the telephone and the address book
function

DVD video

the system functions
COMAND control systemFunctionPage
1COMAND display15
2Tilting and folding COMAND
display
16
3COMAND control unit with
DVD changer
17
4COMAND controller20
5Clear button (CLR)22
6Back button22
COMAND components

15 At a glance
COMAND control system
The currently selected function and the
associated menus are shown on the
COMAND display. The COMAND display is
divided into several areas.
1Status line
2Main functions
3Main area
4SubmenusThe status line 1 displays the time and
the current telephone status.
You can change the main function using
the menu bar 2. The selection is made us-
ing the COMAND controller (
page 20).
In this example, the Audio main function is
set to the radio mode and the main area 3
is active.
i The arrangement of the menus can vary, de-
pending on the equipment. The menus for the full
equipment version are shown in this guide.
Menu overview
Having selected a main function, you will
see the submenu at the bottom edge 4 of
the COMAND display.
Additional menus are available at the top
of the COMAND display 2 for the naviga-
tion, audio and telephone main functions
(
page 16).
COMAND display

16 At a glance
COMAND control system
Main Function menu items
The table below illustrates the structure of the main functions and the associated menu items.
NaviAudioPhoneVideoSystem
Map DisplayFM / AM RadioPhone(Resumes playback if
DVD video is loaded in
changer)(Main function display
appears)
ModeSatRadio*Address Book
Block AreaDisc
Information On MapMemory Card (MP3 mode)
D Highway InformationMusic Register
Aux

17 At a glance
COMAND control system
Tilting and folding COMAND display
! Do not place any objects in front of or be-
hind the COMAND display and/or secure any
objects to the COMAND display itself. This may
obstruct the movement when the display is being
folded in/out.
You can tilt the COMAND display vertically
or fold it in behind the cover. The buttons
are located centrally under the COMAND
display.
1Tilting display
2Folding in displayTilting display
Press 1 once or twice.
The display tilts downwards.
Back into standard position: Press
1 again.
Folding in display
Press 2.
The display folds in behind the
cover. The main function/operating
mode currently selected remains ac-
tive.
Folding out display
Press button on the display cover.
The display folds upwards.
Cleaning instructions
! Avoid touching the COMAND display at all
times. The display has a very sensitive high-gloss
surface, there is a risk of it being scratched. If
you do have to clean it, however, then use a soft,
lint-free cloth.
With the COMAND control unit you can

switch the COMAND on/off

adjust the volume

select the main functions/operating
modes directly

enter phone numbers and accept, re-
ject, initiate and end phone calls

load and eject CDs/DVDs or a PCMCIA
memory card
COMAND control unit

18 At a glance
COMAND control system

19 At a glance
COMAND control system
FunctionPage
1Switching to radio mode
Switching wavebands
Switching to SatRadio*
mode40
42
45
2Switching to CD audio,
DVD audio or MP3 mode
Switching to DVD video
mode
60
77
3Disc slot
Loading CDs/DVDs
Ejecting CDs/DVDs
Updating the map soft-
ware
54
57
112
4Load/Eject button
5Clear button for functions
Entering a phone number
Deleting digit or entire
entry
101
95
6Tuning to a station via the
station memory
42, 42
6Storing stations manually
Selecting DVD changer
compartments
Entering a phone number
Sending DTMF tones43, 43
101
102
7Tuning to a station via sta-
tion search
Fast forward
Selecting next track
42
63, 78
63
8Switching COMAND on/
off
35
9Setting the volume35
aSlot for PCMCIA memory
card
bEject button for
PCMCIA memory card
58
cTuning to a station via sta-
tion search
Fast reverse
Selecting previous track
42
63, 78
63
FunctionPage
dAnswering calls
Initiating calls
Redial101
94,101
101
eRejecting calls
Ending an active call101
103
fOpening System menu164
gMute
Switching hands-free mi-
crophone on/off
Switching traffic and navi-
gation announcements off35
102
35
hSwitching to phone mode
92
jSwitching to navigation
mode
Displaying menu system
118
119
FunctionPage