MERCEDES-BENZ C230 2007 W203 Owner's Manual

Page 191 of 441

190 Controls in detail
Audio system
Button and soft key operation
In these instructions, the alphanumeric
keypad (right side of radio panel) and the
function buttons (left side of radio panel)
are referred to as “buttons”. The four keys
below the display panel are referred to as
“soft keys”.Operation
Switching the unit on/off
Switching on
Turn the SmartKey in the starter switch
to position1 or2.
If the audio system was on as you
removed the SmartKey from the starter
switch, the audio system will
automatically come back on as you
turn the SmartKey to position1 or2.
or
Press M button.Switching off
Remove SmartKey from starter switch.
or
Press M button.
Adjusting the volume
Turn rotary control of N button.
The volume will increase or decrease
depending on the direction turned.
!Do not press directly in the display face.
Otherwise, the display will be damaged.
iIf the radio is switched on without the Smart-
Key in the starter switch, it will automatically
switch off again after approx. 30 minutes.
If your vehicle is equipped with a telephone, the
display may prompt you to enter your PIN (GSM
network) or code (TDMA or CDMA network).
iShould excessively high temperatures occur
while the audio system is being operated, the
display will dim. If temperatures continue to rise,
HIGH TEMP will appear in the display, after which
the audio system will be switched off for a
cooling-down period.
iIf your vehicle equipment includes a Mer-
cedes-Benz specified mobile telephone*, you
can adjust its volume separately from the volume
of the audio system while the telephone is being
used.

Page 192 of 441

191 Controls in detail
Audio system
Adjusting sound functions
The bass and treble functions are called up
by pressing the O button.
Settings for bass and treble are stored
separately for the AM and FM wavebands,
weather band, CD mode and telephone
mode.
Bass
Press O button repeatedly until
BASS appears in the display.
Press + or– soft key to increase or
decrease tone level accordingly.
or
Press RES soft key briefly to reset bass
tones to their center level.The radio switches back to the
standard radio menu 8 seconds after
the last soft key is pressed.
Adjusting treble
Press O button repeatedly until
TREBLE appears in the display.
Press + or– soft key to increase or
decrease tone level accordingly.
or
Press RES soft key briefly to reset treble
tones to their center level.
The radio switches back to the
standard radio menu 8 seconds after
the last soft key is pressed.Sound system*
You can either program the sound settings
manually (
page 191) or choose settings
via preset sound characteristics.
You can select from among the following
settings:
STANDARD: conventional stereo sound.
SURROUND: the sound is set for better
three-dimensional acoustic character-
istics.
SPEECH: the sound is optimized for the
spoken word.
Press O button repeatedly until
STANDARD, SURROUND, or SPEECH appears
in the display.
Press X or Y soft key repeatedly
until the desired sound setting has
been reached.
The sound is set accordingly.
or


Page 193 of 441

192 Controls in detail
Audio system
Press RES soft key briefly.
The sound setting is reset depending
on the sound source activated.
Radio mode: STANDARD
CD/AUX mode: SURROUND
Telephone: SPEECH
The radio switches back to the
standard radio menu 8 seconds after
the last soft key is pressed.
Returning sound functions to factory
settings
Press O button to call up settings
menu in the display.
Press RES soft key briefly; the respec-
tive sound function is reset to its center
level.
or
Press and hold RES soft key until RESET
appears in the display.
The sound settings for bass and treble
are returned to their center level and
the volume is set to a predefined level.
Vehicles with sound system*:
The sound setting is reset depending
on the sound source activated.
Radio mode: STANDARD
CD/AUX mode: SURROUND
Telephone: SPEECH
The radio switches back to the
standard radio menu 4 seconds
after the last soft key is pressed.
Adjusting volume distribution
Call up fader and balance functions by
pressing the P button.Fader
Press P button repeatedly until
FADER appears in the display.
Press V or W soft key.
The volume is distributed accordingly
between the front and rear of the
vehicle.
or
Press RES soft key briefly.
The fader is reset to its center level.
The radio switches back to the
standard radio menu 8 seconds after
the last soft key is pressed.


Page 194 of 441

193 Controls in detail
Audio system
Adjusting balance
Press P button repeatedly until
BALANCE appears in the display.
Press X or Y soft key.
The volume is distributed between the
left and right sides of the vehicle.
or
Press RES soft key briefly.
The balance is reset to its center level.
The radio switches back to the
standard radio menu 8 seconds after
the last button is pressed.Returning volume distribution to
factory settings
Press P button to call up settings
menu in the display.
Press RES soft key briefly; the
respective volume distribution is reset
to its center (flat) level.
or
Press and hold RES soft key until RESET
appears in the display.
The volume distribution settings for
fader and balance are set to their
center level.
The radio switches back to the
standard radio menu 4 seconds after
the last soft key is pressed.Telephone* muting
If your vehicle equipment includes a
Mercedes-Benz specified mobile
telephone*, you can adjust its volume
separately from the volume of the audio
system while the telephone is being used.
Connecting an external audio source
(AUX) to the radio*
An optional dealer-installed cinch-connec-
tor* for connecting an external audio
source may become available for your
vehicle model. Feature description is
based on preliminary information at time
of printing. Contact an authorized
Mercedes-Benz Center for availability.
You can adjust the volume (page 190),
the sound settings (
page 191) and the
volume distribution (
page 192) for the
AUX input.
Calling up AUX mode
Press and hold Q button until AUX
appears in the display.

Page 195 of 441

194 Controls in detail
Audio system
Canceling AUX mode
Press any audio source button.
Radio operation
Selecting radio mode
Press b button.
Calling up wavebands
You can choose from among the FM, AM,
and WB wavebands.
Weather band (
page 196).
Calling up wavebands for radios
without SAT
Press FM or AM soft key to switch
between FM and AM.
The FM and AM wavebands are called
up one after another.
or
Press WB soft key.
The weather band menu is called up.
The waveband currently selected
appears in the upper left-hand corner
of the display.
Calling up wavebands for radios
with SAT
Press FM, AM, or WB soft key repeatedly
until desired waveband has been
selected.
The FM, AM, and WB wavebands are
called up one after another.
The waveband currently selected
appears in the upper left-hand corner
of the display.
Selecting a station
The following options are available for
selecting a station:
Direct frequency input (page 194)
Manual tuning (page 195)
Automatic seek tuning (page 195)
Scan search (page 195)
Station memory (page 195)
Automatic station memory (Autostore)
(
page 196)
The station search proceeds in the
following frequency increments:
200 kHz in FM range
10 kHz in AM range
Direct frequency input
Select desired waveband.
Press * button.
Enter desired frequency with
buttons1to R.
iFM waveband: 87.7......107.9 MHz
AM waveband: 530......1 710 KHz

Page 196 of 441

195 Controls in detail
Audio system
Manual tuning
Select desired waveband.
Press S or Tbutton for approx.
3 seconds.
Press button repeatedly until desired
frequency has been reached.
Step-by-step station tuning takes place
in ascending or descending order. Each
time the button is pressed, the radio
tunes further by 0.2 MHz. During
manual tuning, the radio is muted.
Automatic seek tuning
Select desired waveband.
Press S or T button briefly.
The radio will tune to the next highest
or next lowest receivable frequency.Scan search
Starting scan search
Select desired waveband.
Press SC soft key.
SC will appear in the display. The
radio briefly tunes in all receivable
stations on the waveband selected.
Ending scan search
Press SC soft key or S or T.The station last played will be
selected and
SC disappears from
the display.
Station memory
You can store ten AM and ten FM stations
in the memory.
Storing stations
Tune in desired station.
Press and hold desired station
button1 to R until a brief
signal tone is heard.
The frequency is stored on the
selected station button.
Calling up stations
Press desired station button1
to R briefly.
iYou can only enter frequencies within the re-
spective waveband.
If a button is not pressed within 4 seconds, the
radio will return to the last station tuned.iIf no station is received after two
consecutive scans of the complete frequency
range, then the scan stops at the frequency from
which it began.

Page 197 of 441

196 Controls in detail
Audio system
Autostore – automatic station memory
The Autostore memory function provides
an additional memory level. The station
memory for manually stored stations is not
overwritten.
Calling up Autostore memory level and
storing stations
Press AS soft key briefly.
The radio switches to the Autostore
memory level.
AS and SEARCH
appear in the display and the radio
finds the ten stations with the
strongest signals. These stations
are stored on the station
buttons1 to R in order of
signal strength.
Calling up stations
Press desired station button1
to R.
Leaving the Autostore memory level
Press FM or AMsoft key briefly.
Interrupting radio mode
The radio mode is interrupted by an
incoming call on the telephone*
(
page 212).
Mute on
Press U button.
The radio mode is interrupted and
MUTED appears in the display.
Mute off
Press U button.
The radio mode is again active.Weather band
Press WB soft key.
The weather band station last received
is tuned in.
Selecting a weather band station
directly
Select desired weather band station
with buttons 1 to 7.
If a station cannot be tuned in, a search
is automatically started.

Page 198 of 441

197 Controls in detail
Audio system
Search
Press S or T button to tune in
the next receivable weather band
station.
Scan search
Starting scan search
Press SC soft key.
SC will appear in the display. The
radio briefly tunes in all receivable
weather band stations.
Ending scan search
Press SC soft key or S or T.
The weather band station last
played will be selected and
SC
disappears from the display.Introduction to satellite radio*
(USA only)
SIRIUS satellite radio provides 100 chan-
nels of digital-quality radio, among others
music, sports, news, and entertainment,
free of commercials. SIRIUS satellite radio
uses a fleet of high-power satellites to
broadcast 24 hours per day, coast to
coast, in the contiguous U.S.
This diverse, satellite-delivered program-
ming is available for a monthly subscrip-
tion fee.
For more information and service
availability call the SIRIUS Service
Center (
page 201), or contact
www.siriusradio.com.
iIf no weather band station is received after
three consecutive scans of the complete fre-
quency range, then the scan stops at the chan-
nel with which it began and
NO WB FOUND
appears in the display.
If this happens, switch back to standard radio
mode.
iAdditional satellite radio equipment and a
subscription to a satellite radio service provider
are required for the satellite radio operation de-
scribed here.
Contact an authorized Mercedes-Benz Center
for details and availability for your vehicle.
Note that categories and channels shown in illus-
trations are dependent on programming content
delivered by the service provider. Programming
content is subject to change. Therefore,
channels and categories shown in illustrations
and descriptions contained in this manual may
differ from the channels and categories
delivered by the service provider.
iSatellite radio service may be unavailable or
interrupted from time to time for a variety of rea-
sons, such as environmental or topographic con-
ditions and other things beyond the service
provider’s or our control. Service might also not
be available in certain places (e.g., in tunnels,
parking garages, or within or next to buildings) or
near other technologies.

Page 199 of 441

198 Controls in detail
Audio system
Program categories
The channels are categorized. Categories
allow you to tune to stations broadcasting
a certain type of program (category mode)
(
page 199).
Calling up the SAT main menu
Press SAT soft key.
SAT is displayed in the upper left-hand
corner of the display.
Prior to activation of the satellite radio
service (
page 198).
After activation of satellite radio
service (
page 198).
Prior to activation of the satellite radio
serviceThe telephone number of the SIRIUS
Service Center (888-539-7474) is
displayed.
Press ESN soft key.
The twelve-digit electronic serial
number (ESN) of the SAT tuner*
installed in your vehicle is displayed.
This information is required to call the
SIRIUS Service Center for an activation
request.
After activation of the satellite radio
service
The satellite radio main menu appears.
The radio station selected last is audible,
provided it can be received.The first channel 001 is called up and the
PTY system changes to All categories.
If no station can be received,
ACQUIRING
appears in the display.
If the Satellite radio service is not
activated,
ACQUIRING will also appear in the
radio display and
NO SAT will appear in the
multifunction display.
iCredit card information may also be
required for your application.
The activation process takes approximately 5 to
10 minutes after calling the SIRIUS Service Cen-
ter.
iThe system will tune to a default station if no
station had been selected previously.

Page 200 of 441

199 Controls in detail
Audio system
Selecting a station
The following options are available:
Selecting a station using the selected
category (
page 199).
Tuning via station presets
(
page 199).
Tuning via scan search (page 200).
Tuning via manual channel input
(
page 199).
Tuning via the program category list
(
page 199).
Tuning via station presets
Ten satellite radio station presets are
available.
You can access the presets via number
keys.Accessing via number keys
Enter number of preset you wish to
select, e.g. 1.
The radio plays the station stored
under this number and the PTY function
changes to the category corresponding
to the station.
Tuning via manual channel input
Example: tuning in channel 16
Press * button.
Input line appears in the main radio
menu.
Use number keys to enter desired
channel within 8 seconds, e.g.1
6.The system tunes to channel 16.
The station you have selected begins to
play.
Tuning via the program category list
The category list contains all currently
receivable categories of programs. It is
arranged alphabetically.
Selecting a category
Press PTY soft key.
The current PTY category of the
station is displayed.
iYou can only enter available channel num-
bers.


Page:   < prev 1-10 ... 151-160 161-170 171-180 181-190 191-200 201-210 211-220 221-230 231-240 ... 450 next >