sunroof MERCEDES-BENZ CL550 2008 C216 User Guide

Page 497 of 769

496 Controls in detailAutomatic climate controlRear window defroster
Activating
Switch on the ignition (
page 365).

Press button< (
page 491) up or
down.
The indicator lamp on the button
comes on.
Deactivating

Press button< (
page 491) up or
down.
The indicator lamp on the button goes
out.
Maximum cooling MAXCOOL (USA only)
If U is selected on both the left and
right side and there is a high demand for
cooling, the display “MAXCOOL” appears
in the COMAND display.
This provides the fastest possible cooling
of the vehicle interior (when windows and
tilt/sliding sunroof are closed).
Air recirculation mode
Switch to air recirculation mode to prevent
unpleasant odors from entering the vehicle
from the outside (e.g. before driving in a
tunnel). This setting cuts off the intake of
outside air and recirculates the air in the
passenger compartment.
!
The rear window defroster uses a large
amount of power. To keep battery drain to a min-
imum, switch off the defroster as soon as the
rear window is clear.
i
The defroster is automatically deactivated
after some time of operation depending on the
outside temperature.
Warning!
G
Any accumulation of snow and ice should be
removed from the rear window before driv-
ing. Visibility could otherwise be impaired,
endangering you and others.i
If the rear window defroster switches off too
soon and the indicator lamp goes out, this indi-
cates that too many electrical consumers are op-
erating simultaneously and the load on the
battery is reducing available voltage. The system
responds automatically by deactivating the rear
window defroster.
i
Maximum cooling MAXCOOL is only avail-
able when the engine is running.Warning!
G
Fogged windows impair visibility, endanger-
ing you and others. If the windows begin to
fog on the inside, switching off the air
recirculation mode immediately should clear
interior window fogging. If interior window
fogging persists, make sure the air
conditioning (
page 272) is activated, or
press button;.

Page 498 of 769

497 Controls in detail
Automatic climate control

Activating: Press button,
(page 491) up or down.
The indicator lamp on the button
comes on.

Deactivating: Press button,
(page 491) up or down.
The indicator lamp on the button goes
out.Air recirculation mode with conve-
nience closing or opening feature
i
The air recirculation mode is activated auto-
matically at high outside temperatures.
The indicator lamp on button, is not lit when
the air recirculation mode is automatically acti-
vated.
A quantity of outside air is added when the cool-
ing demand is not at maximum.
If the air conditioning has been turned off
(
page 272) or the outside temperature is be-
low 41°F (5°C), the air recirculation mode will
not switch on automatically.
i
The manually selected air recirculation
mode is deactivated automatically:

after 5 minutes if the outside temperature is
below approximately 41°F (5°C)

after 5 minutes if the air conditioning is
turned off

after 30 minutes if the outside temperature
is above approximately 41°F (5°C)
Warning!
G
Never operate the side windows and the
tilt/sliding sunroof if there is the possibility
of anyone being harmed by the closing pro-
cedure.
When using the air recirculation mode with
convenience closing feature, should the up-
ward movement of a window be blocked by
some obstruction including but not limited
to arms, hands, fingers, etc., the automatic
reversal feature will not operate.
In the event that the procedure causes po-
tential danger, the closing of the side win-
dows can be immediately halted by pressing
the respective window switch. The closing of
the tilt/sliding sunroof can be immediately
halted by moving the tilt/sliding sunroof
switch in the overhead control panel in any
direction.


Page 499 of 769

498 Controls in detailAutomatic climate control
Convenience closing: Press
button
,
for approximately
2 seconds.
The side windows and/or tilt/sliding
sunroof will close. You can release
button
,
once the closing proce-
dure has begun. The windows and
tilt/sliding sunroof continue closing
until they are fully closed. The indicator
lamp on the button comes on. The air
recirculation mode is activated.

Convenience opening: Press
button
,
for approximately
2 seconds.The side windows and/or tilt/sliding
sunroof will return to their previous po-
sition. You can release button
,
once the opening procedure has be-
gun. The windows and tilt/sliding sun-
roof continue opening until they have
reached their previous positions. The
indicator lamp on the button goes out.
The air recirculation mode is deactivat-
ed.
Residual engine heat and ventilation
With the engine switched off, it is possible
to continue to heat or ventilate the interior.
This feature makes use of the residual heat
produced by the engine.
The closing of the side windows and the
tilt/sliding sunroof can be reversed by again
pressing and holding button,.
i
A window or tilt/sliding sunroof will only re-
turn to its previous position if it has not been
moved to another position using the respective
window switch or tilt/sliding sunroof switch af-
ter it was closed with button,.
A window or tilt/sliding sunroof that has been
moved will remain in its current position if
button, is used to reopen the remaining
windows or tilt/sliding sunroof.
i
If you switch on the residual heat function
when outside temperatures are high, only the
ventilation will be switched on.
i
Regardless of the selected air volume, the
blower operates at low speed when heating. In
case of ventilation the blower operates at higher
speed.
i
How long the system will provide heating de-
pends on

the coolant temperature

the temperature set by the operator


Page 507 of 769

506 Controls in detailPower tilt/sliding sunroofOpening and closing power tilt/sliding sunroofWarning!
G
When closing the tilt/sliding sunroof, make
sure that there is no danger of anyone being
harmed by the closing procedure.
If the tilt/sliding sunroof encounters an ob-
struction that blocks its path in a circum-
stance where you are closing the tilt/sliding
sunroof by moving the tilt/sliding sunroof
switch past the resistance point, or by
pressing and holding button‹on the
SmartKey, by pressing and holding the sen-
sor surface (vehicles with KEYLESS-GO*) on
the outside door handle, the automatic re-
versal function will not operate.
The opening/closing procedure of the
tilt/sliding sunroof can be immediately halt-
ed by releasing the switch or, if the switch
was moved past the resistance point and re-
leased, by moving the switch in any direc-
tion.
The tilt/sliding sunroof is made out of glass.
In the event of an accident, the glass may
shatter. This may result in an opening in the
roof.
In a vehicle rollover, occupants not wearing
their seat belts or not wearing them properly
may be thrown out of the opening. Such an
opening also presents a potential for injury
for occupants wearing their seat belts
properly as entire body parts or portions of
them may protrude from the passenger
compartment.
When leaving the vehicle, always remove the
SmartKey or SmartKey with KEYLESS-GO*
from the starter switch, take it with you, and
lock the vehicle. Do not leave children unat-
tended in the vehicle, or with access to an
unlocked vehicle. A child’s unsupervised ac-
cess to a vehicle could result in an accident
and/or serious personal injury.!
To avoid damaging the seals, do not trans-
port any objects with sharp edges which can
stick out of the tilt/sliding sunroof.Do not open the tilt/sliding sunroof if there is
snow or ice on the roof, as this could result in
malfunctions.
If you cannot open or close the tilt/sliding sun-
roof due to a malfunction contact Roadside As-
sistance or an authorized Mercedes-Benz
Center.
!
Please keep in mind that weather conditions
can sometimes change rapidly. Make sure to
close the tilt/sliding sunroof when leaving the
vehicle. If water enters the vehicle interior, vehi-
cle electronics could be damaged which is not
covered by the Mercedes-Benz Limited
Warranty.
i
When the tilt/sliding sunroof is open, reso-
nance noises may result in addition to the usual
wind noises. They are caused by minimal pres-
sure changes in the passenger compartment. To
reduce or eliminate these noises, change the po-
sition of the tilt/sliding sunroof or open a side
window slightly.

Page 508 of 769

507 Controls in detail
Power tilt/sliding sunroof
1Push back to slide sunroof open
2Push forward to slide sunroof closed
3Push up to raise sunroof at rear
4Pull down to lower sunroof at rear
With the sunroof closed or tilted open, a
screen can be slid into the roof opening to
help provide shade. When sliding the sun-
roof open, the screen will also retract.

Switch on the ignition (
page 365).

To open, close, raise or lower, move the
switch to resistance point in the re-
quired direction1to4 until the
tilt/sliding sunroof has reached the de-
sired position.

Express-operation: To open, close,
raise or lower, move the switch past
the resistance point in the required
direction1to4 and release.
The tilt/sliding sunroof opens or closes
completely.

Stopping during Express-operation:
Move the switch in any direction.
i
You can also open or close the tilt/sliding
sunroof using the SmartKey, see “Summer open-
ing feature” (
page 404) and “Convenience
closing feature” (page 404). Depending on
current position, the tilt/sliding sunroof may
also open or close when the air recirculation
button, (
page 491) is pressed and held
for 2 seconds.
i
If PRE-SAFE
® has been activated, the
tilt/sliding sunroof closes automatically until
only a small gap remains.
i
With the SmartKey in starter switch
position0 or removed from the starter switch,
the tilt/sliding sunroof can be operated

until you open the driver’s or passenger door

for up to approximately 5 minutes
i
If the movement of the tilt/sliding sunroof is
blocked during the closing procedure, the sun-
roof will stop and reopen slightly.

Page 509 of 769

508 Controls in detailPower tilt/sliding sunroofSynchronizing
The tilt/sliding sunroof must be synchro-
nized
if the tilt/sliding sunroof can only be
opened with a jerking motion

after a malfunction

Switch on the ignition (
page 365).

Press and hold the sunroof switch in
the direction of arrow3 until the
tilt/sliding sunroof is fully raised at the
rear.

Keep holding the sunroof switch in the
direction of arrow3 for approximately
1 second.

Check the Express-operation feature
(page 507).
If the tilt/sliding sunroof opens com-
pletely, the sunroof is synchronized.
Otherwise repeat the above steps.
!
Do not open the tilt/sliding sunroof com-
pletely if it is not aligned. Otherwise you could
damage the tilt/sliding sunroof.

Page 758 of 769

757 Index
P
Paintwork, Cleaning 597
Panic alarm
Audible alarm and flashing
exterior lamps 64
Panic button 64
Parcel net in front passenger
footwell 511
Park Assist* 467
Cleaning system sensors 601
Messages in display 632, 634
System sensors 601
Warning indicators 31, 470
Parking 412, 542
Parking and standing lamps
Replacing bulbs 689
Parking position
Exterior rear view mirrors 384
Parktronic* 463
Cleaning system sensors 600
Malfunctioning 467
System sensors 600
Warning indicators 31, 465
Parts service 720PASS AIR BAG OFF indicator lamp see
Front passenger front air bag off
indicator lamp
Passenger compartment 547
Passenger safety see Occupant safety
PCMCIA card
Ejecting (COMAND) 118
Loading (COMAND) 117
Pedals 539
Plastic parts, cleaning 604
POIs 225
Poly-V-belt drive 724
Layout 724
Potential problems associated with
underinflated and overinflated
tires 576
Power assistance 539
Power closing assist for doors and
trunk lid 363
Power folding exterior rear view
mirrors 382
Power seats
Folding back front seat
backrests 371
Folding forward front seat
backrests 371Power tilt/sliding sunroof 506
Opening/closing 506
Synchronizing 508
Power washer 596
Power windows 402
Cleaning 603
Opening/closing 402
Rear side windows,
Blocking operation 63
Practical hints 622, 681
Premium unleaded gasoline 551, 735,
737
PRE-SAFE
®
56
Message in display 635
Messages in display 642
PRE-SAFE
® Brake*
Intermittent signal tone 77
Preventive occupant safety see PRE-SAFE
®
Problems
While driving 411
With vehicle 21
Product information 13
Production options weight 587
Program mode see Automatic
transmission, Automatic shift program

Page 762 of 769

761 Index
Storage tray/telephone* compartment
in front armrest 510
Under the front seats 511
Storing tires 563
Summer opening feature 404
Sun visors 516
Sunroof see Power tilt/sliding sunroof
Sunshades
Extending or retracting rear window
sunshade (COMAND) 267
Suspension tuning
Setting (ABC) 461
Symbols used in this operator’s
manual 19
System settings (COMAND)
Bluetooth
® settings 176
Display 255
Favorite button 259
Menu overview 255
Reset 259
Setting the system language 258
Time settings 255
Voice Control settings
(COMAND) 257T
Tachometer 435
Overspeed range 435
Tail lamps
Cleaning lenses 599
Messages in display 668
Tar stains 596
Tele Aid 522
Automatic Maintenance Call 530
Call priority 528
Emergency calls 523
Hands-free microphone 37
Information 527
Information button 525
Initiating an emergency call
manually 525
Messages in display 675
Remote door lock 529
Remote door unlock 529
Roadside Assistance 526
Roadside Assistance button 525
SOS button 525
Stolen Vehicle Recovery
services 530
System self-check 523Telephone cradle
Changing 521
Telephone* 519
“911” emergency call
(COMAND) 141
Accepting/ending a call
(COMAND) 148
Answering/ending a call (Instrument
cluster control system) 297
Call lists (COMAND) 146
Changing mobile phone cradle 521
Compartment 510
Dialing (Instrument cluster control
system) 296
Entering the telephone number
(COMAND) 149
Hands-free microphone 37
Inserting in cradle 520
Installing a different mobile
phone cradle 522
Operation 294
Operation (COMAND) 137
Phone book (COMAND) 154
Phone book (Instrument cluster
control system) 296
PIN (COMAND) 142

Page 763 of 769

762 Index
PIN2 (COMAND) 143
PUK / PUK2 (COMAND) 143
Redialing (COMAND) 150
Redialing (Instrument cluster
control system) 297
Removing from cradle 521
Single call connection
(COMAND) 151
Speed dialing (COMAND) 150
Submenu overview (COMAND) 144
Switching on/off (COMAND) 139
Transferring a call (COMAND) 153
Unlock code (COMAND) 143
Voice Control 308
Telephone* cradle
Changing 521
Temperature
Outside temperature indicator 31
Setting interior temperature
(COMAND) 270
Tires 570
Tightening torque, Wheel bolts 701
Tilt/sliding sunroof see Power tilt/sliding
sunroofTime
Setting (COMAND) 255
TIN 588
Tire and Loading Information
Placard 565
Tire Identification Number see TIN
Tires 561
Advanced Tire Pressure Monitoring
System (Advanced TPMS) 572
And Rims 727
And Wheels 561
Care and maintenance 562
Chains 591
Checking inflation pressure electroni-
cally with Advanced Tire Pressure
Monitoring System
(Advanced TPMS) 572
Cleaning 563
Cold tire inflation pressure 586
Combination low tire pressure
malfunction telltale 31, 618
Direction of rotation 564
Driving instructions 543
Important notes on tire
inflation pressure 570Inflation pressure 569
Information placard 565
Inspection 562
Load rating 578, 588
Load rating, Maximum 582, 586
Minispare wheel 683, 730
Ply composition and material
used 588
Problems under-/overinflation 569
Retreads 561
Rotating 589
Service life 562
Sizes 727
Snow 590
Speed rating 544, 579, 588
Storing 563
Temperature 570, 584
Terminology 585
Total load limit 588
TPMS malfunction telltale 31, 618
Traction 544, 588
Tread depth 563
Tread depth, Winter 590
Treadwear indicators 588
Vehicle maximum load on 588

Page:   < prev 1-10 11-20