warning light MERCEDES-BENZ CLA 2014 Workshop Manual

Lanes
White guide line withoutturning the
steering wheel, vehicle width including
the exterior mirrors (static)
Yellow lane marking tires at current
steering wheel angle, vehicle width to the
outer side of the wheels (dynamic)
"Red guide line for the vehicle width
including the exterior mirrors, for current
steering wheel angle (dynamic)
!Bumper
Guide lines
!Bumper
Red guide line at a distanceof
approximately 10 in (0.25 m) from the
rear of the vehicle
Yellow guide line at a distance of
approximately 13 ft(4.0m)from the rear
of the vehicle
Vehicle center axle (marker assistance)
Yellow guide line at a distance of
approximately 3 ft (1.0 m) from the rear
of the vehicle
The lanes and guide lines are only displayed
if you have engaged reverse gear.
The distance specifications only apply to
objects that are at ground level.
Additional displays on vehicles with PARKTRONICand COMAND
Front warning display
Additional PARKTRONIC measurement
operational readiness indicator
"Rearwarning display
Vehicles with PARKTRONIC and
COMAND:if PARKTRONIC is operational
(Ypage 175), an additional operational
readiness indicator will appear in COMAND
display.If the PARKTRONIC warning
displays are active or light up, warning
displaysand"are also active or light up
correspondingly in the COMAND display.
"Reverse parking" function
XMake sure that the rear view camera is
activated and the "Reverse parking"
function is selected; see the separate
operating instructions for the audio
system/COMAND.
The lane and the guide lines are shown.
184Driving systems
Driving and parking

FCC.Do not tamper with, alter, or use in
any non-approved way.
Any unauthorized modification to this
device could void the user’s authority to
operate the equipment.
Monitoring range of the sensors
In particular, the detection of obstacles can
be impaired if:
Rdirt on the sensors or anything else
covering the sensors
Rthere is poor visibility, e.g. due to fog, heavy
rain or snow
Ra narrow vehicle traveling in front, e.g. a
motorbike or bicycle
Rthe road has very wide lanes
Rthe road has narrow lanes
Ryou are not driving in the middle of the lane
Rthere are barriers or similar lane borders
Vehicles in the monitoring range are then not
indicated.
Blind Spot Assist monitors the area up to
10 ft(3.0m)behind your vehicle and directly
nextto your vehicle, as shown in the diagram.
For this purpose, Blind Spot Assist uses radar
sensors in the rear bumper.
If the lanes are narrow, vehicles driving in the
lane beyond the lane next to your vehicle may
be indicated, especially if the vehicles are not
driving in the middle of their lane. This may
be the case if the vehicles are driving on the
inner side of their lane.
Due to the nature of the system:
Rwarnings may be issued in error when
driving close to crash barriers or similar
solid lane borders.
Rwarnings may be interrupted when driving
alongside particularly long vehicles, e.g.
trucks, for a prolonged time.
The two sensors for Blind Spot Assist are
integrated into the sides of the rear bumper.
Make sure that the bumper is free of dirt, ice
or slush in the vicinityofthe sensors. For
example, the radar sensors must not be
covered by bicycle racks or overhanging
loads. Following a severe impact or in the
event of damage to the bumpers, have the
function of the radar sensors checked at a
qualified specialist workshop. Blind Spot
Assist may otherwise not work properly.
Indicator and warning display
Blind Spot Assist is not active at speeds below
approximately 20 mph (30 km/h). Vehicles in
the monitoring range are then not indicated.
Yellow indicator lamp/red warning lamp
When Blind Spot Assist is activated, indicator
lampin the exterior mirrors lights up
yellow at speeds of up to 20 mph(30km/h).
At speeds above 20 mph (30 km/h), the
indicator lamp goes out and Blind Spot Assist
is operational.
If a vehicle is detected withinthe monitoring
range of Blind Spot Assist at speeds above
Driving systems189
Driving and parking
Z

20 mph (30km/h), then warning lampon
the corresponding side lights up red. This
warning is always emitted whenavehicle
enters the blind spot monitoring range from
behind or from the side.When you overtake
a vehicle, the warning only occurs if the
difference in speed is less than7mph
(12 km/h).
The yellow indicator lamp goes out if reverse
gear is engaged. In this event, Blind Spot
Assist is no longer active.
The brightness of the indicator/warning
lamps is adjusted automatically according to
the ambient light.
Collision warning
If a vehicle is detected in the monitoring range
of Blind Spot Assist and you switch on the
corresponding turn signal, a double warning
tone sounds. Red warning lampflashes. If
the turn signal remains on, vehicles detected
are indicated by the flashing of red warning
lamp.There are no further warning tones.
Switching on Blind Spot Assist
XMake sure that Blind Spot Assist is
activated in the on-board computer
(Ypage 205).
XTurn the SmartKey to position2in the
ignition lock.
Warning lampsin the exterior mirrors
light up red for approximately
1.5 seconds and then turn yellow.
Lane Keeping Assist
General notes
Lane Keeping Assist monitors the area in
front of your vehicle by means of a camera at
the top of the windshield. Lane Keeping Assist
detects lane markings on the road and warns
you before you leave your lane
unintentionally.
Lane Keeping Assist camera
If you selectkmon the on-board computer in
theDisplay Unit Speed-/Odometer
function (Ypage 206), Lane Keeping Assist
is active starting ataspeed of 60 km/h. If the
milesdisplay unit is selected, the assistance
range begins at 40 mph.
Important safety notes
GWARNING
Lane Keeping Assist may not always clearly
recognize lane markings.
In this case, Lane Keeping Assist may:
Rgive an unnecessary warning
Rnot give a warning
There is a risk of an accident.
Always pay particular attention to the traffic
situation and stay in lane, in particular if
warned by Lane Keeping Assist.
GWARNING
The Lane Keeping Assist warning does not
returnthe vehicle to the original lane. There
is a risk of an accident.
You should always steer, brake or accelerate
yourself, in particular if warned by Lane
Keeping Assist.
If you fail to adapt your driving style, Lane
Keeping Assist can neither reduce the risk of
an accident nor override the laws of physics.
Lane Keeping Assist cannot take into account
the road, traffic and weather conditions. Lane
Keeping Assist is merely an aid. You are
responsible for the distance to the vehicle in
190Driving systems
Driving and parking

Useful information
iThis Operator's Manual describes all
models and all standard and optional
equipment of your vehicle available at the
time of publication of the Operator's
Manual. Country-specific differences are
possible. Please note that your vehicle may
not be equipped with all features
described. This also applies to safety-
related systems and functions.
iRead the information on qualified
specialist workshops: (Ypage 25).
Important safety notes
GWARNING
If you operate information systems and
communication equipment integrated in the
vehicle while driving, you will be distracted
from traffic conditions. You could also lose
control of the vehicle. There is a risk of an
accident.
Only operate the equipment when the traffic
situationpermits.Ifyou are not sure that this
is possible, park the vehicle paying attention
to traffic conditions and operate the
equipment when the vehicle is stationary.
GWARNING
If the instrument cluster has failed or
malfunctioned, you may not recognize
function restrictions in systems relevant to
safety. The operating safety of your vehicle
may be impaired. There is a risk of an
accident.
Drive on carefully. Have the vehicle checked
at a qualified specialist workshop
immediately.
You must observe the legal requirements for
the country in which you are currently driving
when operating the on-board computer.
The on-board computer only shows messages
or warnings from certain systems in the
multifunction display.You should therefore
make sure your vehicle is operating safely at
all times. Otherwise, a vehicle that is not
operating safely may cause an accident.
For an overview, see the instrument panel
illustration (Ypage 29).
Displays and operation
Instrument cluster lighting
The lighting in the instrument cluster, in the
displays and the controls in the vehicle
interior can be adjusted using the brightness
control knob.
The brightness control knob is located on the
bottom left of the instrument cluster
(Ypage 29).
XTurn the brightness control knob clockwise
or counter-clockwise.
If the light switch is set to,or
, the brightness is dependent upon
the brightness of the ambient light.
iThe light sensor in the instrument cluster
automatically controls the brightness of
the multifunction display.
In daylight, the displays in the instrument
cluster are not illuminated.
Coolant temperature display
GWARNING
Opening the hood when the engine is
overheated or when there is a fire in the
engine compartment could expose you to hot
gases or other service products. There is a
risk of injury.
Let an overheated engine cool down before
opening the hood. If there is a fire in the
engine compartment, keep the hood closed
and contact the fire department.
!Adisplay message is shown if the coolant
temperature is too high.
194Displays and operation
On-board computer and displays

Only deactivate ESP®in the situations
described in the following.
It may be best to deactivate ESP®in the
following situations:
Rwhen using snow chains
Rin deep snow
Ron sand or gravel
Activating/deactivating ESP®on AMG
vehicles (Ypage 66).
For further information about ESP®, see
(Ypage 65).
XStart the engine.
XPress theorbutton on the
steering wheel to select theDriveAssist
menu.
XPress theorbutton to select
ESP.
XPress thebutton.
XTo activate/deactivate:press the
button again.
ESP®is deactivated if thewarning
lamp in the instrument cluster lights up
continuously when the engine is running.
If thewarning lamp and the
warning lamp are lit continuously, ESP®is not
available due to a malfunction.
Observe the information on warning lamps
(Ypage 244).
Observe the information on display messages
(Ypage 213).
Switching the distance warning
function on and off
XPress theorbutton on the
steering wheel to select theDriveAssist
menu.
XPress theorbutton to select
Distance Warning.
XPress thebutton.
The current selection is displayed.
XTo activate/deactivate:press the
button again.
When the distance warning function is
deactivated, the
symbol appears in
the multifunction display in the assistance
graphics display.
Further information on the distance warning
function (Ypage 62).
Activating/deactivating COLLISION
PREVENTION ASSISTPLUS
XPress theorbutton on the
steering wheel to selecttheDriveAssist
menu.
XPress theorbutton to select
Collision Prevent. Assist.
XPress thebutton.
The current selection is displayed.
XTo activate/deactivate:press the
button again.
When COLLISION PREVENTION ASSIST
PLUS is deactivated, the
symbol
appears in the multifunction display in the
assistance graphics display.
For further information about COLLISION
PREVENTION ASSIST PLUS, see (Ypage 64).
Activating/deactivating ATTENTION
ASSIST
XPress theorbutton on the
steering wheel to select theDriveAssist
menu.
XPress theorbutton to select
Attention Assist.
XPress thebutton.
The current selection is displayed.
XTo activate/deactivate:press the
button again.
When ATTENTION ASSIST is deactivated,
thesymbol appears in the
204Menus and submenus
On-board computer and displays

multifunction display in the assistance
graphics display.
For further information about ATTENTION
ASSIST, see (Ypage 186).
Activating/deactivating Blind Spot
Assist
XPress theorbutton on the
steering wheel to select theDriveAssist
menu.
XPress theorbutton to select
Blind Spot Assist.
XPress thebutton.
The current selection is displayed.
XTo activate/deactivate:press the
button again.
For further information about Blind Spot
Assist, see (Ypage 188).
When theBlind Spot Assist: Sensors
Deactivatedmessage is shown, the radar
sensors are deactivated.
XSwitch on the radarsensor system
(Ypage 208).
Activating/deactivating Lane Keeping
Assist
XPress theorbutton on the
steering wheel to select theDriveAssist
menu.
XPressorto selectLane
Keeping Assist.
XPress thebutton.
The currentselection is displayed.
XPressto confirm.
XPress theorbutton to setOff,
StandardorAdaptive.
XPress thebutton to save the setting.
When Lane Keeping Assist is activated, the
multifunction display shows the lane
markings as bright lines in the assistance
graphic.
For further information about Lane Keeping
Assist, see (Ypage 190).
Maintenance menu
In theServicemenu, you have the following
options:
RCalling up display messages in message
memory (Ypage 212)
RChecking the tire pressure electronically
(Ypage 320)
Restarting the tire pressure loss warning
system (Canada only) (Ypage 319)
RCalling up the service due date
(Ypage 284)
Settings menu
Introduction
In theSettingsmenu, you have the following
options:
RChanging the instrument cluster settings
RChanging the light settings
RChanging the vehicle settings
RChanging the convenience settings
RRestoring the factory settings
Menus and submenus205
On-board computer and displays
Z

Safety systems
Display messagesPossible causes/consequences and
Solutions

Currently
Unavailable See
Operator's Manual
ABS (Anti-lock Braking System), ESP®(Electronic Stability
Program), BAS (Brake Assist), the HOLD function and hill start
assist are temporarily unavailable.
COLLISION PREVENTION ASSIST/COLLISION PREVENTION
ASSIST PLUS may also have failed.
In addition, the,andwarning lamps light up in
the instrument cluster.
ATTENTION ASSIST is deactivated.
Possible causes are:
Rself-diagnosis is not yet complete.
Rthe on-board voltage may be insufficient.
GWARNING
The brake system continues to function normally, but without the
functions listed above. The wheels could therefore lock if you
brake hard, for example.
The steerability and braking characteristics may be severely
affected. The braking distance in an emergency braking situation
can increase.
If ESP®is not operational, ESP®is unable to stabilize the vehicle.
There is an increased risk of skidding and an accident.
XCarefully drive a short distance on a suitable stretch of road,
making slight steering movements at a speed above 12 mph
(20 km/h).
If the display message disappears, the functions mentioned
above are available again.
If the display message continues to be displayed:
XDrive on carefully.
XVisit a qualified specialist workshop.

Inoperative See
Operator's Manual
ABS, ESP®, BAS, the HOLD function and hill start assist are
unavailable due to a malfunction.
COLLISION PREVENTION ASSIST/COLLISION PREVENTION
ASSIST PLUS may also have failed.
In addition, the,,andwarning lamps light
up in the instrument cluster.
ATTENTION ASSIST is deactivated.
GWARNING
Display messages213
On-board computer and displays
Z

Display messagesPossible causes/consequences and
Solutions
The brake system continues to function normally, but without the
functions listed above. The wheels could therefore lockifyou
brake hard, for example.
The steerability and braking characteristics may be severely
affected. The braking distance in an emergency braking situation
can increase.
If ESP®is not operational, ESP®is unable to stabilize the vehicle.
There is an increased risk of skidding and an accident.
XDrive on carefully.
XVisit a qualified specialist workshop immediately.

Currently
Unavailable See
Operator's Manual
ESP®, BAS, the HOLD function and hill start assist are temporarily
unavailable.
COLLISION PREVENTION ASSIST/COLLISION PREVENTION
ASSIST PLUS may also have failed.
In addition, theandwarning lamps light up in the
instrument cluster.
ATTENTION ASSIST is deactivated.
The self-diagnosis function might not be complete, for example.
GWARNING
The brake system continues to function normally, but without the
functions listed above.
The braking distance in an emergency braking situation can thus
increase.
If ESP®is not operational, ESP®is unable to stabilize the vehicle.
There is an increased risk of skidding and an accident.
XCarefully drive a short distance on a suitable stretch of road,
making slight steering movements at a speed above 12 mph
(20 km/h).
If the display message disappears, the functions mentioned
above are available again.
If the display message continues to be displayed:
XDrive on carefully.
XVisit a qualified specialist workshop.
214Display messages
On-board computer and displays

Display messagesPossible causes/consequences and
Solutions

Inoperative See
Operator's Manual
ESP®, BAS, the HOLD function and hill start assist are unavailable
due to a malfunction.
COLLISION PREVENTION ASSIST/COLLISION PREVENTION
ASSIST PLUSmay also have failed.
In addition, theandwarning lamps light up in the
instrument cluster.
ATTENTION ASSIST is deactivated.
GWARNING
The brake system continuesto function normally, but without the
functions listed above.
The braking distance in an emergency braking situation can thus
increase.
If ESP®is not operational, ESP®is unable to stabilize the vehicle.
There is an increased risk of skidding and an accident.
XDrive on carefully.
XVisit a qualified specialist workshop.


Inoperative See
Operator's Manual
EBD (electronic brake force distribution), ABS, ESP®, BAS, the
HOLD function and hill start assist are not available due to a
malfunction.
COLLISION PREVENTION ASSIST/COLLISION PREVENTION
ASSIST PLUS may also have failed.
In addition, the,andwarning lamps light up in
the instrument cluster and a warning tone sounds.
ATTENTION ASSIST is deactivated.
GWARNING
The brake system continues to function normally, but without the
functions listed above. The front and rear wheels could therefore
lock if you brake hard, for example.
The steerability and braking characteristics may be severely
affected. The braking distance in an emergency braking situation
can increase.
If ESP®is not operational, ESP®is unable to stabilize the vehicle.
There is an increased risk of skidding and an accident.
XDrive on carefully.
XVisit a qualified specialist workshop immediately.
Display messages215
On-board computer and displays
Z

Display messagesPossible causes/consequences and
Solutions
(USA
only) (Canada
only)
Please Release
Parking Brake
The red(USA only)/ (Canada only) indicatorlamp
flashes and a warning tone sounds.Acondition for automatic
release of the electric parking brake is not fulfilled (Ypage 154).
You are driving with the electric parking brake applied.
XRelease the electric parking brake manually.
The red(USA only)/ (Canada only) indicator lamp
flashes and a warning tone sounds.
You are using the electric parking brake for emergency braking
(Ypage 154).
(USA
only) (Canada
only)
Parking Brake See
Operator's Manual
The yellow warning lamp lights up.
The electric parking brake is malfunctioning.
To apply:
XSwitch the ignition off.
XPress the electric parking brake handle for at least ten seconds.
XShift the transmission toP.
XConsult a qualified specialist workshop.
The yellow warning lamp and the red(USA
only)/ (Canada only) indicator lamp light up.
The electric parking brake is malfunctioning.
To release:
XSwitch off the ignition and turn it back on.
XRelease the electric parking brake manually.
or
XRelease the electric parking brake automatically (Ypage 154).
If the electric parking brake still cannot be released:
XDo not drive on.
XConsult a qualified specialist workshop.
216Display messages
On-board computer and displays