MERCEDES-BENZ CLK320 COUPE 2005 C209 Owner's Manual

149 Controls in detail
Control system
Instrument cluster submenu
Access the
Instr. cluster
submenu via
the
Settings
menu. Use the
Instr. clus-
ter
submenu to change the instrument
cluster display settings.
The following functions are available:Selecting temperature display mode

Move the selection marker with
buttonæ orç to the Instr. cluster
submenu.

Press buttonj ork repeatedly
until the message
Temp. indicator

appears in the multifunction display.
The selection marker is on the current
setting.

Press buttonæ orç to set tem-
perature unit to
°C (degrees Celsius)
or
°F (degrees Fahrenheit).Selecting speedometer display mode

Move the selection marker with
buttonæ orç to the Instr. cluster
submenu.

Press buttonj ork repeatedly
until the message
Display unit
Speed-/odometer appears in the
multifunction display.
The selection marker is on the current
setting.

Press buttonæ or ç to set
speedometer unit to
km or
miles
.
Function
Page
Selecting temperature display
mode
149
Selecting speedometer display
mode
149
Selecting language
150
Selecting display (speed display
or outside temperature) for
status display
150
Selecting display (speed display
or outside temperature) for
standard display
151

150 Controls in detailControl systemSelecting language
Move the selection marker with
buttonæ orç to the Instr. cluster
submenu.

Press buttonj ork repeatedly
until the message
Language
appears in
the multifunction display.
The selection marker is on the current
setting.

Press buttonæ orç to select
the language to be used for the
multifunction display messages.
Available languages:

German


English


French


Italian


SpanishSelecting display (speed display or out-
side temperature) for status indicator

Move the selection marker with
buttonæ orç to the Instr. cluster
submenu.

Press buttonj ork repeatedly
until the message
Status line dis-
play
appears in the display.
The selection marker is on the current
setting.

Press buttonæ orç to select
the desired setting.iYou will see the status indicator when
you have called up a different display
from the standard display.

151 Controls in detail
Control system
Selecting display (speed display or out-
side temperature) for standard display
Move the selection marker with
buttonæ orç to the Instr. cluster
submenu.

Press buttonj ork repeatedly
until the message
Basic display

appears in the display.
The selection marker is on the current
setting.

Press buttonæ orç to select
the display mode shown in the basic
display.Time/Date submenu
Access the
Time/Date
submenu via the
Settings
menu. Use the
Time/Date

submenu to change the instrument cluster
display settings.
The following functions are available:Time synchronization with head unit*
This function can only be seen on vehicles
with COMAND* and navigation module*.

Move the selection marker with
buttonæ orç to the
Time/Date

submenu.

Press buttonj ork repeatedly
until the message
Time sync. with
head unit
appears in the multifunction
display.
The selection marker is on the current
setting.

Press buttonæ orç to select
the desired setting.
Function
Page
Time synchronization with
head unit*
151
Setting the time (hours)
152
Setting the time (minutes)
152
Selecting automatic time change
(Daylight Saving Time (DST)
summer/Standard time winter)
153
Setting the date (month)
153
Setting the date (day)
153
Setting the date (year)
154

152 Controls in detailControl systemSetting time (hours)
This function can only be seen with audio
system.
Move the selection marker with
buttonæ orç to the
Time/Date

submenu.

Press buttonj ork repeatedly
until the message
Clock, hours
Confirm by press. R
appears in the
multifunction display.
The selection marker is on the hour
setting.

Press buttonæ orç to set the
hour.

Press the reset button in the instru-
ment cluster (
page 134) to confirm.
The hour is set and stored.
Setting time (minutes)
This function can only be seen with audio
system.

Move the selection marker with
buttonæ orç to the
Time/Date

submenu.

Press buttonj ork repeatedly
until the message
Clock, minutes
Confirm by press. R
appears in the
multifunction display.
The selection marker is on the minutes
setting.

Press buttonæ orç to set the
minutes.

Press the reset button in the instru-
ment cluster (
page 134) to confirm.
The minutes are set and stored.
iVehicles with COMAND*:
For information on setting the time,
refer to the separate COMAND
operating instructions.
iVehicles with COMAND*:
For information on setting the time,
refer to the separate COMAND
operating instructions.

153 Controls in detail
Control system
Selecting automatic time change
(Daylight Saving Time (DST)
summer/Standard time winter)
Move the selection marker with
buttonæ orç to the
Time/Date

submenu.

Press buttonj ork repeatedly
until the message
Daylight savings
Summer/winter Automatic
appears in
the multifunction display.
The selection marker is on the current
setting.

Press buttonæ orç to select if
the changeover between summer and
winter time should be automatic or
manual. Setting the date (month)
This function can only be seen with audio
system.

Move the selection marker with
buttonæ orç to the
Time/Date

submenu.

Press buttonj ork repeatedly
until the message
Set date month

appears in the multifunction display.
The selection marker is on the month
setting.

Press buttonæ orç to set the
month.
Setting the date (day)
This function can only be seen with audio
system.

Move the selection marker with
buttonæ orç to the
Time/Date

submenu.

Press buttonj ork repeatedly
until the message
Set date day

appears in the multifunction display.
iVehicles with COMAND*:
For information on setting the date,
refer to the separate COMAND
operating instructions.
iVehicles with COMAND*:
For information on setting the date,
refer to the separate COMAND
operating instructions.


154 Controls in detailControl system
The selection marker is on the day
setting.

Press buttonæ orç to set the
day.
Setting the date (year)
This function can only be seen with audio
system.

Move the selection marker with
buttonæ orç to the
Time/Date

submenu.

Press buttonj ork repeatedly
until the message
Set date year

appears in the multifunction display.
The selection marker is on the year
setting.

Press buttonæ orç to set the
year.Lighting submenu
Access the
Lighting
submenu via the
Set-
tings
menu. Use the
Lighting
submenu
to change the lamp and lighting settings on
your vehicle.
The following functions are available:
iVehicles with COMAND*:
For information on setting the date,
refer to the separate COMAND
operating instructions.
Function
Page
Setting daytime running lamp
mode (USA only)
155
Setting locator lighting
156
Exterior lamps delayed
switch-off
156
Interior lighting delayed
switch-off
157


155 Controls in detail
Control system
Setting daytime running lamp mode
(USA only)
Move the selection marker with
buttonæ orç to the
Lighting

submenu.

Press buttonj ork repeatedly
until the message
Lamp circuit
headlamp
appears in the multifunction
display.
The selection marker is on the current
setting.

Pressæ orç to select manual
operation (
manual
) or daytime running
lamp mode (
constant
) activated.
With daytime running lamp mode activated
and the exterior lamp switch in
positionM or U the low beam
headlamps are switched on when the
engine is running.
In low ambient light conditions the
following lamps will switch on additionally:


Parking lamps


Tail lamps


License plate lamps


Side marker lamps
For more information on the daytime run-
ning lamp mode, see “Lighting”
(
page 124).
iThis function is not available in
countries where the daytime running
lamp mode is mandatory and therefore
in a constant mode.
iIf you turn the exterior lamp switch to
another position, the corresponding
lamp(s) will switch on.
For safety reasons, resetting the Lighting
submenu to factory settings
(
page 147) while driving will not
deactivate the daytime running lamp
mode.
The following message appears in the
multifunction display:
Lighting – Cannot be completely
reset to factory settings while
driving
.

156 Controls in detailControl systemSetting locator lighting
With the locator lighting feature activated
and the exterior lamp switch in
positionU, the following lamps will
switch on when the vehicle is unlocked
with the SmartKey during darkness:

Parking lamps


Tail lamps


License plate lamps


Side marker lamps


Front fog lamps
The locator lighting switches off when the
driver’s door is opened.
If you do not open a door after unlocking
with the SmartKey the lamps will switch off
automatically after approximately
40 seconds.
To activate locator lighting:

Make sure the function surround light-
ing is set to
on, see (
page 156).

Move the selection marker with
buttonæ orç to the
Lighting
submenu.

Press buttonj ork repeatedly
until the message
Function Surround
lighting
appears in the multifunction
display.
The selection marker is on the current
setting.

Press buttonæ orç to switch
the locator lighting function
On.

Turn the exterior lamp switch to
position U when exiting the vehicle
(page 124).
The locator lighting feature is
activated.Setting night security illumination
(Headlamps delayed shut-off)
Use this function to set whether and how
long you would like the exterior lamps to
illuminate during darkness after exiting the
vehicle and all doors closed.
With the delayed shut-off feature activated
and the exterior lamp switch in
positionU before the engine is turned
off, the following lamps will switch on after
you have removed the SmartKey from the
starter switch:


Parking lamps


Tail lamps


License plate lamps


Side marker lamps


Front fog lamps
If you do not open a door after removing
the SmartKey from the starter switch, the
lamps will switch off automatically after
approximately 60 seconds.

157 Controls in detail
Control system

Move the selection marker with
buttonæ orç to the
Lighting
submenu.

Press buttonj ork repeatedly
until the message
Headlamps delayed
shut-off
appears in the multifunction
display.
The selection marker is on the current
setting.

Pressæ orç to select the de-
sired lamp-on period.You can select:


0 s
, the delayed shut-off feature is
deactivated


15 s
, 30 s
, 45 s
or
60 s
, the delayed
shut-off feature is activated

Turn the exterior lamp switch to
position U before tuning off the
engine (
page 124).
The headlamps delayed shut-off
feature is activated.
You can temporarily deactivate the de-
layed shut-off feature:

Before leaving the vehicle, turn the
SmartKey in the starter switch to
position0.

Then turn it to position2 and back
to0.
The delayed shut-off feature is
deactivated. It will reactivate as soon
as you reinsert the SmartKey in the
starter switch.Setting interior lighting delayed shut-off
Use this function to set whether and how
long you would like the interior lighting to
remain lit during darkness after you have
removed the SmartKey from the starter
switch.

Move the selection marker with
buttonæ orç to the
Lighting
submenu.

Press buttonj ork repeatedly
until the message
Interior lamp de-
layed shut-off appears in the
multifunction display.
The selection marker is on the current
setting.

Pressæ orç to select the de-
sired lamp-on time period.
iYou can reactivate this function within
ten minutes by opening a door.


158 Controls in detailControl system
You can select:

0 s
, the delayed shut-off feature is
deactivated.


5 s
, 10 s
, 15 s
or
20 s
, the interior
lighting delayed shut-off feature is
activated with the desired lamp-on
period.
Vehicle submenu
Access the
Vehicle
submenu via the
Settings
menu. Use the
Vehicle
submenu
to make general vehicle settings.
The following functions are available:Setting automatic locking
Use this function to activate or deactivate
the automatic central locking. With the
automatic central locking system
activated, the vehicle is centrally locked at
vehicle speeds of approximately 9 mph
(15 km/h).

Move the selection marker with
buttonæ orç to the
Vehicle

submenu.

Press buttonj ork repeatedly
until the message
Automatic door
lock
appears in the multifunction
display.
The selection marker is on the current
setting.

Press buttonæ orç to switch
the automatic central locking
on or
off
.Convenience submenu
Access the
Convenience
submenu via the
Settings
menu. Use the
Convenience
sub-
menu to change the settings for a number
of convenience features.
The following functions are available:
Function
Page
Setting automatic locking
158
Function
Page
Activating easy-entry/exit
feature
159
Setting key-dependency
160
Setting parking position for exte-
rior rear view mirror
160