jacking MERCEDES-BENZ CLS 2014 Owners Manual

Securing the vehicle on slight downhillgradients
XOn light downhill gradients:place
chocks or othersuitableitemsinfront of
the wheelsofthe front and rearaxle.
Raisingthe vehicle
GWARNING
If youdonot positionthe jack correctly at the
appropriate jackingpoint of the vehicle, the
jack could tip over with the vehicle raised.
There isarisk of injury.
Only position the jack at the appropriate
jackingpoint of the vehicle. The base of the
jack must be positioned vertically, directly
under the jackingpoint of the vehicle.
!The jack is designed exclusively for
jackingupthe vehicle at the jackingpoints.
Otherwise, your vehicle could be damaged.
The following must be observed when raising
the vehicle:
Rto raise the vehicle, only use the vehicle-
specific jack that has been tested and
approved by Mercedes-Benz. If used
incorrectly, the jack could tip over with the
vehicle raised.
Rthe jack is designed only to raise and hold
the vehicle forashort time whileawheel
is being changed. It is not suited for
performing maintenancework under the
vehicle.
Ravoid changing the wheel on uphill and
downhill slopes.
Rbefore raising the vehicle, secure it from
rolling away by applying the parking brake
and insertingwheel chocks. Never
disengage the parking brake while the
vehicle is raised.
Rthe jack must be placed onafirm, flat and
non-slip surface. Onaloose surface, a
large, load-bearing underlay must be used.
Onaslippery surface,anon-slip underlay
must be used, e.g. rubber mats.
Rdo not use wooden blocks or similar
objectsasajack underlay.Otherwise, the
jackwill not be able to achieveits load-
bearingcapacity due to the restricted
height.
Rmakesure that the distancebetween the
underside of the tires and the grounddoes
not exceed 1.2in(3cm).
Rnever place your hands and feet under the
raised vehicle.
Rnever lie under the raised vehicle.
Rnever start the engine when the vehicle is
raised.
Rnever open or closeadoor or the trunk lid
when the vehicle is raised.
Rmakesure that no persons are present in
the vehicle when the vehicle is raised.
XUsinglug wrench,loosen the boltson
the wheel you wish to change by about one
full turn. Do not unscrew the bolts
completely.
Changingawheel359
Wheels and tires
Z

XPosition jack$at jacking point.
Example
XMake sure the foot of the jack is directly
beneath the jacking point.
XTurn crank!clockwise until jack$sits
completely on jacking pointand the
base of the jack lies evenly on the ground.
XTurn crank!until the tire is raised a
maximum of 1.2 in (3 cm) off the ground.
Removingawheel
!AMG vehicles:during removaland
repositioning of the wheel, the wheel rim
can strike the ceramic-brake disc and
damage it. Therefore, take precautions and
getasecond persontoassist you.
Alternatively, you can useasecond
alignment bolt.
!Do not place wheel bolts in sand or on a
dirty surface. The bolt and wheel hub
threads could otherwise be damaged when
you screw them in.
XUnscrew the uppermost wheel bolt
completely.
XScrew alignment boltinto the thread
instead of the wheel bolt.
XUnscrew the remaining wheel bolts fully.
XRemove the wheel.
Mountinganew wheel
GWARNING
Oiled or greased wheel boltsordamaged
wheel bolts/hub threads can cause thewheel
boltstocomeloose.Asaresult, you could
loseawheel while driving. There isarisk of
accident.
Never oil or grease wheel bolts. In the event
of damage to the threads, contactaqualified
specialist workshop immediately.Have the
damagedwheel boltsorhub threads
replaced/renewed. Do notcontinue driving.
360Changingawheel
Wheels and tires