MERCEDES-BENZ CLS63AMG 2008 W219 Owner's Manual

400 Practical hints
Unlocking/locking in an emergency
Fuel filler flap emergency release
In case the central locking system does
not release the fuel filler flap, you can open
it manually.
1Release knob
Open trunk.
Remove right-side tail trim.
Pull release knob1 in direction of ar-
row.
The fuel filler flap can know be opened.Manually unlocking the gear selector
lever
In case of power failure, the gear selector
lever can be manually unlocked, e.g. to tow
the vehicle.
1Selector lever cover
2Release
Insert flat, blunt object (e.g. screwdriv-
er) into the left edge of cover1 at the
position indicated by the arrows.
Loosen cover1 using this object.
Using your hands, pull cover1 out
and remove.
Push down and hold release2 in
direction of arrow.
Simultaneously move gear selector
lever out of positionP.
The gear selector lever is now un-
locked.
iThe gear selector lever is locked again as
soon as you place it in positionP again.

401 Practical hints
Resetting activated head restraints
Resetting activated head restraints
If the active head restraint have been trig-
gered in an accident, the head restraints
must be reset. Otherwise, active head re-
straint cannot offer any additional protec-
tion in the event of another rear-end
collision.
You can tell that the head restraints have
been activated when they have been
moved forward and cannot be adjusted.
Take the reset tool out of the
Mercedes-Benz vehicle literature
pouch.
Guide reset tool into center of head re-
straint between head restraint cushion
and rear head restraint cover.
Press reset tool forward in direction of
arrow.
Press reset tool downward until you
hear the head restraint release
mechanism audibly engage.
Pull out reset tool.
Firmly press head restraint cushion
backward towards rear head restraint
cover until it engages.
Repeat this procedure for second head
restraint.
For information on head restraint adjust-
ment, see “Seats” (
page 41).
iFor your convenience, we recommend that
you have this work carried out by an authorized
Mercedes-Benz Center.
You will find the reset tool for manually operating
the head restraints in the Mercedes-Benz vehicle
literature pouch.
Warning!G
For safety reasons, have the active head re-
straints checked by an authorized
Mercedes-Benz Center after a rear-end colli-
sion.
!Be careful not to damage upholstery.
Warning!G
When pushing back the head restraint cush-
ion, take care that your fingers do not be-
come caught between the head restraint
cushion and the cover. Failing to do so may
lead to injury.

402 Practical hints
Replacing SmartKey batteries
If the batteries in the SmartKey/SmartKey
with KEYLESS-GO* are discharged, the ve-
hicle can no longer be locked or unlocked.
It is recommended to have the batteries re-
placed at an authorized Mercedes-Benz
Center.Batteries contain materials that can harm
the environment if disposed of improperly.
Recycling of batteries is the preferred
method of disposal. Many states require
sellers of batteries to accept old batteries
for recycling.
Replacement batteries: Lithium, type
CR 2025 or equivalent.
Remove the mechanical key out of the
SmartKey/SmartKey with
KEYLESS-GO* (
page 398).1Mechanical key
2Battery compartment
Insert mechanical key 1 into opening.
Press mechanical key 1 in direction of
arrow.
The battery compartment is unlatched.
Pull battery compartment 2 out of the
housing.
Warning!G
Batteries contain poisonous and corrosive
substances. Therefore keep the batteries
out of reach of children.
If a battery is swallowed, seek medical help
immediately.
Warning!G
SmartKey batteries contain Perchlorate ma-
terial, which may require special handling
and regard for the environment. Check with
your local government’s disposal guidelines.
California residents, see
http://www.dtsc.ca.gov/HazardousWaste
/Perchlorate/index.cfm.
iWhen inserting the batteries, make sure
they are clean and free of lint.
iWhen changing batteries, always replace
both batteries.
The required replacement batteries are available
at any authorized Mercedes-Benz Center.

403 Practical hints
Replacing SmartKey batteries
3Batteries
4Contact springs
Pull out batteries3.
Using a line-free cloth, insert new bat-
teries 3 under contact springs 4 with
the positive terminal (+) side facing up.
Return battery compartment 2
(
page 402) into housing until it locks
into place.
Slide the mechanical key back into the
SmartKey/SmartKey with
KEYLESS-GO*.
Check the operation of the SmartKey/
SmartKey with KEYLESS-GO*.

404 Practical hints
Replacing bulbs
Bulbs
Safe vehicle operation depends on proper
exterior lighting and signaling. It is there-
fore essential that all bulbs and lamp as-
semblies are in good working order at all
times.
Correct headlamp adjustment is extremely
important. Have headlamps checked and
readjusted at regular intervals and when a
bulb has been replaced. See your autho-
rized Mercedes-Benz Center for headlamp
adjustment.iIf the headlamps or front fog lamps are
fogged up on the inside as a result of high humid-
ity, driving the vehicle a distance with the lights
on should clear up the fogging.iAuxiliary bulbs will be brought into use when
lamps malfunction. Read and observe the mes-
sages in the multifunction display (
page 382).

405 Practical hints
Replacing bulbs
Front lamps
LampType
1Additional turn signal
lampsLED
2Turn signal lamp3457 AK
3Halogen headlamps:
Low beam
Bi-Xenon* headlamps:
Low and high beam
1
1Vehicles with Bi-Xenon* headlamps: Low beam
and high beam use the same D2S-35W lamp. Do
not replace the Bi-Xenon bulbs yourself. Contact
your authorized Mercedes-Benz Center.
H7 (55 W)
D2S-35 W
4Side marker lampW 5 W
LampType
5Halogen headlamps:
High beam/high beam
flasher
Bi-Xenon* headlamps:
High beam flasher
H7 (55 W)
H7 (55 W)
Halogen headlamps:
Parking and standing
lamp
Bi-Xenon* headlamps:
Parking an standing
lamp
W 5 W
Blue Vision
LED
6Front fog lamp
Corner-illuminating
front fog lamp*H11 (55 W)
H11 (55 W)

406 Practical hints
Replacing bulbs
Rear lamps Notes on bulb replacement

Use only 12 volt bulbs of the same type
and with the specified watt rating.

Switch lights off before changing a bulb
to prevent short circuits.

Always use a clean lint-free cloth when
handling bulbs.

Your hands should be dry and free of oil
and grease.

If the newly installed bulb does not light
up, contact an authorized
Mercedes-Benz Center.
LampType
7High mounted brake
lampLED
8 Brake, tail, parking,
standing, backup lamps
and turn signal lamps.
Rear fog lampHiP
LED*
9License plate lampsC5W
Warning!G
Bulbs and bulb sockets can be very hot. Al-
low the lamp to cool down before changing
a bulb.
Keep bulbs out of reach of children.
Halogen lamps contain pressurized gas. A
bulb can explode if you:

touch or move it when hot

drop the bulb

scratch the bulb
Wear eye and hand protection.
Because of high voltage in Xenon lamps, it is
dangerous to replace the bulb or repair the
lamp and its components. We recommend
that you have such work done by a qualified
technician.

407 Practical hints
Replacing bulbs
Have the LEDs and bulbs for the following
lamps replaced by an authorized
Mercedes-Benz Center:

Additional turn signals in the exterior
rear view mirrors

High mounted brake lamp

Bi-Xenon* lamps

Front fog lamps

Front side marker lamps

Parking and standing lamps (vehicles
with Bi-Xenon* headlamps only)

Rear lamps (except license plate
lamps)
Replacing bulbs for front lamps
1Housing cover for low beam halogen or
Bi-Xenon* headlamp
2Housing cover for high beam head-
lamp/high beam flasher bulb and for
parking and standing lamp bulb3Bulb socket for turn signal lamp bulb
4Bulb holder of high beam bulb
5Bulb socket for parking and standing
lamp bulb
6Bulb holder of low beam bulb
Before you start to replace a bulb for a
front lamp, do the following first:
Turn the exterior lamp switch to
positionM (
page 126).
Open the hood (page 286) (except
for side marker lamps).
!Do not replace the LEDs yourself. You could
otherwise damage the LEDs or parts of the vehi-
cle. Only have the LEDs replaced by an autho-
rized Mercedes-Benz Center.
Warning!G
Do not remove the cover1 for the Bi-Xe-
non* headlamp. Because of high voltage in
Xenon* lamps, it is dangerous to replace the
bulb or repair the lamp and its components.
We recommend that you have such work
done by a qualified technician.

408 Practical hints
Replacing bulbs
Low beam bulb (halogen headlamps
only)
Turn housing cover1 counterclock-
wise and remove it.
Turn bulb holder6 with the bulb coun-
terclockwise and remove it.
Pull the bulb at its socket out of bulb
holder6.
Insert the new bulb so that its socket
locates in the recess of bulb holder6
and is level to it.
Reinsert bulb holder6 with the bulb in
the lamp and turn clockwise.
Align housing cover1 and turn it
clockwise.High beam bulb/high beam flasher
bulb (halogen headlamps)/high beam
flasher bulb (Bi-Xenon* headlamps)
Turn housing cover2 counterclock-
wise and remove it.
Turn bulb holder4 with the bulb coun-
terclockwise and remove it.
Pull the bulb at its socket out of bulb
holder4.
Insert the new bulb so that its socket
locates in the recess of bulb holder4
and is level to it.
Reinsert bulb holder4 with the bulb in
the lamp and turn clockwise.
Align housing cover2 and turn it
clockwise.Front turn signal lamp bulb
Turn bulb socket3 with the bulb
counterclockwise and remove it.
Press gently onto the bulb and turn
counterclockwise out of bulb
socket3.
Press the new bulb gently into bulb
socket3 and turn clockwise until it
engages.
Place bulb socket3 back into the
lamp and turn it clockwise.

409 Practical hints
Replacing bulbs
Parking and standing lamp bulb
Halogen headlamps
Turn housing cover2 counterclock-
wise and remove it.
Pull out bulb socket5 with the bulb.
Pull the bulb out of the bulb socket5.
Press the new bulb into bulb socket5.
Press bulb socket5 back into the
lamp.
Align housing cover2 and turn it
clockwise.
Bi-Xenon* headlamps
In vehicles with Bi-Xenon* headlamps, the
bulbs of the parking and standing lamps
are LEDs.
Replacing bulbs for rear lamps
Tail lamp unit
The tail lamps are equipped with HiP bulbs.License plate lamp
1License plate lamp
2Screws
Turn the exterior lamp switch to
positionM (
page 126).
Loosen both screws2.
Remove license plate lamp1.
Replace the bulb.
Reinstall license plate lamp1.
Retighten screws2.
!Do not replace the LEDs yourself. You could
otherwise damage the LEDs or parts of the vehi-
cle. Only have the LEDs replaced by an autho-
rized Mercedes-Benz Center.
Warning!G
The bulbs in the tail lamps cannot be re-
placed individually. The tail lamp bulbs are
under pressure and could explode during an
attempt to replace them.
If the tail lamps are malfunctioning, have
them exchanged at an authorized
Mercedes-Benz Center.