brake MERCEDES-BENZ E-CLASS 2003 Manual PDF

344 Practical hintsBatteries
Disconnecting the battery
Depress the parking brake firmly or
move the gear selector lever to
positionP.

Open the trunk (
page 261).

Disconnect battery negative lead1.

Remove cover2 from the positive ter-
minal.

Disconnect the battery positive lead.
Removing the battery
Remove the screw-nuts securing the
battery.

Remove the battery bracket.

Take out the battery.
Charging and reinstalling the battery
Charge battery in accordance with the
instructions of the battery charger
manufacturer.

Reinstall the charged battery. Follow
the previously described steps in re-
verse order.
!Never loosen or detach battery termi-
nal clamps while the engine is running
or the key is in the starter switch. Oth-
erwise the alternator and other elec-
tronic components could be severely
damaged.
Have the battery checked regularly by
an authorized Mercedes-Benz Center.
Contact your authorized
Mercedes-Benz Center for further infor-
mation.Warning!
G
Do not place metal objects on the battery as
this could result in a short circuit.
Use leak-proof battery only to avoid the risk
of acid burns in the event of an accident.
Warning!
G
With a disconnected battery

the brake boosting effect is not avail-
able.
You need more power to brake and
brake pedal travel is increased. If neces-
sary, you must depress the brake pedal
with full power.


you can no longer turn the ignition key
or, in cars with KEYLESS-GO*, pressing
the KEY-LESS-GO button* on the gear
selector lever has no effect.


the gear selector lever is locked in
position P.
ProCarManuals.com

347 Practical hints
Jump starting
The battery is located in the trunk on the
right hand side underneath the luggage
box (
page 325). Only jump start the ve-
hicle from the battery in the trunk.

Make sure that the two vehicles do not
touch.

Turn off all electrical consumers.

Apply parking brake.

Shift selector lever to positionP.1Positive terminal of charged battery
2Positive terminal of discharged battery
3Vehicle ground
4Negative terminal of charged battery

Connect positive terminals1 and2 of
the batteries with the jumper cables.
Clamp cable to charged battery1 first.

Start engine of the vehicle with the
charged battery and run at idle speed.

Connect negative terminal4 of the
charged battery and vehicle ground3
(lock ring of the trunk lid lock) in the
trunk with the jumper cable. Clamp ca-
ble to charged battery4 first.

Start the engine of the disabled vehi-
cle.
Now you can again turn on the electrical
consumers. Do not turn on the lights under
any circumstances.

Remove the jumper cables first from
vehicle ground3 and negative
terminal4 and then from positive
terminals1 and2.

Have the battery checked at the next
authorized Mercedes-Benz Center.
Warning!
G
Keep flames or sparks away from battery.
Do not smoke.
Observe all safety instructions and precau-
tions when handling automotive batteries
(page 266).
iThe message
Malfunction - electric
consumers switched off
may appear
in the instrument cluster. It will disap-
pear as soon as the battery is suffi-
ciently charged.
!Vehicles with automatic transmission:
Do not tow-start the vehicle.
ProCarManuals.com

348 Practical hintsTowing the vehicle
Towing the vehicleTowing the vehicle
Mercedes-Benz recommends that the vehi-
cle be transported with all wheels off the
ground using flatbed or appropriate wheel
lift/dolly equipment.
When circumstances do not permit the
recommended towing methods, the vehi-
cle may be towed with all wheels on the
ground or front wheels raised only so far as to have the vehicle moved to a safe loca-
tion where the recommended towing
methods can be employed.
!Use flatbed or wheel lift/dolly equip-
ment with key in starter switch turned
to position0.
Do not tow with sling-type equipment.
Towing with sling-type equipment over
bumpy roads will damage radiator and
supports.
To prevent damage during transport,
do not tie down vehicle by its chassis or
suspension parts.
Switch off the tow-away alarm and the
automatic central locking
!If the vehicle is towed with the front
axle raised, the engine must be shut off
(key in starter switch position0 or1).
Otherwise, the ESP will immediately be
engaged and will apply the rear wheel
brakes.
When towing the vehicle with all wheels
on the ground, the selector lever must
be in positionN and the key must be in
starter switch position2. When towing
the vehicle with all wheels on the
ground, the vehicle may be towed only
for distances up to 30 miles (50 km)
and at a speed not to exceed 30 mph
(50 km/h).
!To be certain to avoid a possibility of
damage to the transmission, however,
we recommend the drive shaft be dis-
connected at the rear axle drive flange
for any towing beyond a short tow to a
nearby garage.
ProCarManuals.com

349 Practical hints
Towing the vehicle
Warning!
G
If circumstances require towing the vehicle
with all wheels on the ground, always tow
with a tow bar if:

the engine will not run


there is a malfunction in the SBC brake
system


there is a malfunction in the power sup-
ply or in the vehicle’s electrical system
as that will be necessary to adequately con-
trol the towed vehicle.
Prior to towing the vehicle with all wheels on
the ground, make certain that the key is in
starter switch position2.
If the key is left in the starter switch
position0 for an extended period of time, it
can no longer be turned in the switch. In this
case, the steering is locked. To unlock, re-
move key from starter switch and reinsert.
iTo signal turns while being towed with
the hazard warning flasher in use, turn
key in starter switch to position2 and
activate the combination switch for the
left or right turn signal in the usual
manner – only the selected turn signal
will operate.
Upon canceling the turn signal, the haz-
ard warning flasher will operate again.
Warning!
G
The brake system requires electrical power
to operate.
A malfunction in the vehicle’s power supply
or electrical system may impair brake sys-
tem operation and switch it into its
limp-home (emergency operation) mode. To
brake, the driver must then apply signifi-
cantly greater brake pedal pressure and de-
press the pedal much further to obtain the
expected braking effect. If necessary, apply
full pressure to the brake pedal. Brakes are
only applied to the front wheels. Stopping
distance is increased! Adapt your driving
style accordingly. SBC brake system
(page 77).
With the engine not running, there is no
power assistance for the steering system. In
this case, it is important to keep in mind that
a considerably higher degree of effort is nec-
essary to steer the vehicle. Adapt your driv-
ing accordingly.
ProCarManuals.com

366 Technical dataFuels, coolants, lubricants etc.
Fuels, coolants, lubricants etc.CapacitiesVehicle components and their respective
lubricants must match. Therefore use only
brands tested and recommended by us.Please refer to the Factory Approved Ser-
vice Products Pamphlet, or inquire at your
authorized Mercedes-Benz Center.
Model
Capacity
Fuels, coolants, lubricants etc.
Engine with oil filter
E320
E500
8.5 US qt (8.0 l)
8.0 US qt (7.5 l)
Recommended engine oils
Automatic transmission
8.0 US qt (7.5 l)
MB Automatic Transmission Oil
1
1MB part no. 001 989 21 03 10Rear axle
E320
E500
1.06 US qt (1 l)
1.37 US qt (1.3 l)
Hypoid gear oil SAE 85 W 90
Power steering
approx. 1.1 US qt (1.0 l)
MB Power Steering Fluid (Pentosin
CHF 11S)
Front wheel hubs
approx. 3.0 oz (85 g) each
High temperature roller bearing grease
Brake system
0.64 US qt (0.6 l)
MB Brake Fluid (DOT 4+)
Cooling system
E320
E500
approx. 10.7 US qt (10 l)
approx. 11.9 US qt (11.3 l)
MB 325.0 Anticorrosion / Antifreeze
Fuel tank including a reserve of
21.12 US gal (80.0 l)
2.38 US gal (9.0 l)
Premium unleaded gasoline:
Posted Octane 91 (Avg. of 96
RON / 86 MON)
Air conditioner system
R-134a refrigerant and special PAG lu-
bricant oil (never R-12)
ProCarManuals.com

368 Technical dataFuels, coolants, lubricants etc.Engine oils
Engine oils are specifically tested for their
suitability in our engines. Therefore, use
only engine oils recommended by
Mercedes-Benz. Information on recom-
mended brands is available in the Factory
Approved Service Products Pamphlet, or at
your authorized Mercedes-Benz Center.
Please follow FSS recommendations for
scheduled oil changes. Failure to do so
could result in engine damage not covered
by the Mercedes-Benz Limited Warranty.
Engine oil additives
Do not blend oil additives with engine oil.
They may be harmful to the engine opera-
tion.
Damage or malfunctions resulting from
blending oil additives are not covered by
the Mercedes-Benz Limited Warranty.Air conditioner refrigerant
R-134a (HFC) refrigerant and special PAG
lubricating oil is used in the air conditioner
system.
Never use R-12 (CFC) or mineral-based lu-
bricating oil. Otherwise damage to the
system will occur.
Brake fluid
During vehicle operation, the boiling point
of the brake fluid is continuously reduced
through the absorption of moisture from
the atmosphere. Under extremely strenu-
ous operating conditions, this moisture
content can lead to the formation of bub-
bles in the system, thus reducing the sys-
tem’s efficiency.
Therefore, the brake fluid must be re-
placed every two years, preferably in the
spring.
Only brake fluid approved by
Mercedes-Benz is recommended. Your au-
thorized Mercedes-Benz Center will pro-
vide you with additional information.
ProCarManuals.com

375 Technical terms
ABS
(A
ntilock B
rake S
ystem)
Prevents the wheels from locking up
during braking so that the vehicle can
continue to be steered.
Alignment bolt
Metal pin with thread. The centering
pin is an aid used when changing a tire
to align the wheel with the wheel hub.
BabySmart
TM airbag deactivation
system
This system detects if a special system
compatible child restraint seat is in-
stalled on the front passenger seat. The
system will automatically deactivate
the passenger front airbag when such a
seat is properly installed
(PASSENGER AIRBAG OFF indicator
lamp located in the center console
lights up). See your authorized
Mercedes-Benz Center for availability. BabySmart
TM compatible child seats
Special restraint system for children.
The sensor system for the passenger
seat prevents deployment of the pas-
senger side airbag if a BabySmart
TM
compatible child seat is installed.
BAS
(B
rake A
ssist S
ystem)
System for potentially reducing braking
distances in emergency braking situa-
tions. The system is activated when it
senses an emergency based on how
fast the brake is applied.
Bi-Xenon headlamps*
Headlamps which use an electric arc as
a light source and produce a more in-
tense light than filament headlamps.
Bi-Xenon headlamps produce low
beam and high beam.CAC
(C
ustomer A
ssistance C
enter)
Mercedes-Benz customer service cen-
ter which can help you with any ques-
tions about your vehicle and provide
assistance in the event of a break-
down.
CAN system
(C
ontroller A
rea N
etwork)
Data bus network serving to control ve-
hicle functions such as door locking or
windshield wiping.
Cockpit
All instruments, switches, buttons and
indicator/warning lamps in the passen-
ger compartment needed for vehicle
operation and monitoring.
ProCarManuals.com

379 Technical terms
Restraint systems
Seat belts, belt tensioners, airbags and
child restraint systems. As indepen-
dent systems, their protective func-
tions complement one another.
RON
(R
esearch O
ctane N
umber)
The Research Octane Number for gaso-
line as determined by a standardized
method. It is an indication of a gaso-
line's ability to resist undesired detona-
tion (knocking). The average of both
the ->MON (Motor Octane Number)
and RON (Research Octane Number) is
posted at the pump, also known as
ANTI-KNOCK INDEX.
SBC
(S
ensotronic B
rake C
ontrol)
Electronically controlled hydraulic
braking system for increased braking
safety and comfort.Shift lock
When the vehicle is parked, this lock
prevents the transmission selector le-
ver from being moved out of positionP
without key turned and brake pedal de-
pressed.
SRS
(S
upplemental R
estraint S
ystem)
Seat belts, emergency tensioning de-
vice and airbags. Though independent
systems, they are closely interfaced to
provide effective occupant protection.
Tele Aid System
(T
elematic A
larm I
dentification on D
e-
mand)
The Tele Aid system consists of three
types of response: automatic and man-
ual emergency, roadside assistance
and information. Tele Aid is initially ac-
tivated by completing a subscriber
agreement and placing an acquain-
tance call.The Tele Aid system is operational pro-
viding that the vehicle’s battery is
charged, properly connected, not dam-
aged and cellular and GPS coverage is
available.
Telematics*
A combination of the terms "telecom-
munications" and "informatics".
Tightening torque
Force times lever arm (e.g. a lug
wrench) with which threaded fasteners
such as wheel bolts are tightened.
Tire speed rating
Part of a tire designation; indicates the
speed range for which a tire is ap-
proved.
Traction
Force exerted by the vehicle on the
road via the tires.
ProCarManuals.com

382 IndexAIRMATIC DC (Dual Control) 209
Alarm
Audible 72, 82
Canceling 82
Visual 82
Alarm system
Anti-theft 82
Alignment bolt (vehicle tool kit) 340, 375
Antiglare
Automatic 157
Antilock brake system (ABS) 375
Anti-theft alarm system
Arming 82
Canceling alarm 82
Disarming 82
Anti-theft systems 81
Anti-theft alarm system 82
Immobilizer 81
Tow-away alarm 82
Ashtray 231
AUDIO menu 126
Selecting radio station 127
Automatic antiglare for rear view
mirror 157Automatic central locking
Activating/deactivating (control
system) 142
Automatic climate control
Temperature sensor 27
Automatic climate control* 172
Adjusting air distribution 177
Adjusting air volume 166, 177
Air recirculation mode 178
Defrosting 178
Rear window defroster 169, 180
Residual heat utilization 182
Residual ventilation 182
Setting the temperature 176
Automatic headlamp mode 113
Automatic lighting control
Activating 116
Deactivating 116
Automatic locking when driving 99
Automatic transmission 151
Accelerator position 156
Emergency operation (Limp Home
Mode) 156
Gear ranges 153Gear selector lever position 154
Gear shifting malfunctions 156
Kickdown 156
One-touch gearshifting 152
Program mode selector switch 155
Selector lever position 151
Starting the engine 43
Winter program mode 155
B
BabySmart
TM
Compatible child seats 375
Self-test 68
BabySmart
TM airbag deactivation
system 67, 375
Backrest
Folding forward 220
Folding rearward 221
BAS 74, 375
Messages in display 297, 298
Batteries, SmartKey
Changing 329
Check lamp 87
Checking 88
ProCarManuals.com

383 Index
Batteries, vehicle
Charging 344
Disconnecting 344
Messages in display 303, 304
Reconnecting 345
Removing 344
Service 343
Battery discharged
Jump starting 346
Bi-Xenon headlamps* 375
Blocking
Rear window operation 71
Brake assist system (BAS) 375
Brake pads
Message in display 305
Brakes
Warning lamp 291
Bulbs, replacing
Front lamps 332, 334
High beam bulb (Bi-Xenon* headlamps
only) 334
License plate lamps 336
Parking lamps 335
Standing lamps 335
Tail lamp assemblies 336C
CAC (Customer Assistance Center) 375
Calling up
Distronic* settings 128
Range (distance to empty) 147
CAN system 375
Cargo area see Trunk 88
Cargo tie-down rings 225
Cassette player
Operating 128
CD player*
Operating 127, 128
Center console
Lower part 26
PASSENGER AIRBAG OFF indicator
lamp 294
Upper part 25
Centigrade
Setting temperature units 134
Central locking
Automatic 99
From inside 100
Switch 100
Switching on/off (control
system) 142
Unlocking from inside 100Central locking switch 100
Changing
Batteries (SmartKey) 329
Key setting 143
Vehicle level 210
Charcoal filter 180
Charging
Vehicle batteries 344
Child safety 65
Airbags 58
Infant and child restraint systems 61,
65
Child safety switch see Blocking of rear
window operation 71
Cigarette lighter 232
Cleaning
Headlamps 158
Parktronic* system sensor 284
Windshield 48
Cleaning and care of the vehicle
Distronic system sensor 283
MB Tex upholstery 285
Climate control 162
Adjusting 166
Defrosting 167
Setting the temperature 165
ProCarManuals.com