ESP MERCEDES-BENZ E-CLASS SALOON 2015 Owners Manual

X
Remove th eprotective film from th evehicle
tool ki tand put it ove rthe collapsible emer-
gency spar ewheel.
X Stow th ecollapsible emergenc yspare
whee lintheemergenc yspar ew hee lwell
under th eboot/luggag ecom partment. Inflating th
ecollapsible emergency
spar ewheel
! Inflat
ethe collapsible emergenc yspare
whee lusin gthe tyreinflation compressor
before lowerin gthe vehicle. The whee lrim
could otherwise be damaged.
! Do no
toperate th etyrei nflation com-
presso rfor longer than eigh tminute sata
time without abreak. It may otherwise
overheat.
The tyr einflation compressor can be oper-
ate dagain once it has cooled down. X
Moun tthe collapsible emergenc yspare
whee lasd escribed (Y page 426).
The collapsible emergenc yspar ew heel
mus tbem ountedbefore it is inflated.
X Pull connector ?and th ehoseo ut of the
housing.
X Remove th ecap from th evalveont hecol-
lapsible emergenc yspar ew heel.
X Screw union nut :of th ehoseo ntot he
valve.
X Mak esureo n/of fswitch Aof th etyre
inflation compressor is set to 0.X
Inser tconnector ?into a12Vs ocket
(Y page 366) in your vehicle.
X Turn th ekeyto position 1in th eignition
loc k(Ypage 179).
X Press on/off switch Aon th etyrei nflation
compressor to I.
The tyr einflation compressor is switched
on .The tyr eisinflated. The tyr epressur eis
shown on pressur egauge =.
X Pump th etyretot hespecified tyr epres-
sure.
The specified tyr epressur eisprinted on
th ey ellow label of th eemergenc yspare
wheel.
X Whe nthe specified tyr epressur ehas been
reached, press on/off switch Aon the
electric air pump to 0.
The tyr einflation compressor is switched
off.
X Turn th ekeyto position 0in th eignition
lock.
X If th etyrep ressur eishigher than th especi-
fie dp ressure, press pressur erelease valve
button ;until th ecorrect tyrep ressure
has been reached.
X Unscrew union nut :on th ehosef romt he
valve.
X Screw th evalvec ap onto th ecollapsible
emergenc yspar ew hee lvalv ea gain.
X Stow connector ?and th ehoseint he
lower section of th etyrei nflation compres-
sor.
X Stow th etyrei nflation compressor in the
vehicle. Emergency spar
ewheel
467Wheels and tyres Z

sion surrounding the possible health risk
posed by electromagnetic fields.
Observe the notes on operating mobile
phones (Y page 367).
The following aerialp ositions may be used for
the correct installation of RF transmitters: Saloon: approved aerial positions
:
Front roof area
; Rear roof area
= Rear wing
? Boot lid Estate: approved aerial positions
:
Front roof area
; Rear roof area
= Rear wing
i When fitting an aerialont
he front roof
area of vehicles with asliding sunroof,
observe the sweeping range of the roof.
On vehicles with panorama sliding sunroof,
fitting an aerialtot he front or rear roof area
is not permitted. On the rear wing, it is recommended that
you position the aerialont he side of the
vehicle closest to the centre of the road.
Use Technical Specification ISO/TS 21609
(RoadV ehicles–"EMC guidelines for fitting
aftermarket radio frequency transmitting
equipment") when retrofitting RF (radio fre-
quency) transmitters. Comply with the legal
requirements for add-on parts.
If your vehicle has fittings for two-way radio
equipment, use the power supplyora erial
connections intended for use with the basic
wiring. Be sure to observe the manufacturer's additional instructions when installing.
Deviations with respect to wavebands, maxi-
mum transmission outputs or aerialp ositions
must be approved by Mercedes-Benz.
The maximum transmission output (PEAK) at
the base of the aerialm ust not exceed the
following values: Waveband Maximum
transmission output Short wave
3-54M
Hz 100 W
4mw
aveband
74 -88M Hz 30 W
2mw
aveband
144 -174 MHz 50 W
Trunked radio/Tetra
380
-460 MHz 10 W
70 cm waveband
400
-460 MHz 35 W
Mobile communications
(2G/3G/4G) 10 WVehicle electronics
471Technical data Z

X
Slide the right-hand front sea ttoits rear-
mos tposition.
X Fol dfloor covering :upwards.
VIN ;can be seen. Engine number
The engine number is stampe dinto the crank-
case. Yo ucan obtain further information from
any qualified specialist workshop. Servic
eproducts and capacities Important safety notes
G
WARNING
Service product can be poisonous and haz-
ardou stohealth. There is ariskofi njury.
Observe the instructions on the respective
original containe rwhenu sing ,storing and dis-
posing off service products. Alway sstore ser-
vice products in the seale doriginal container.
Alway skeep service products ou tofthe reach
of children. H
Environmental note
Dispose of service products in an environ-
mentally-responsible manner.
Service products includ ethe following:
R fuels
R exhaus tgas aftertreatment additives, e.g.
AdBlue ®
R lubricants (e.g. engine oil, transmissio noil)
R coolant
R brake fluid
R windscreen washe rfluid
R climate control system refrigerant
Components and service products mus tbe
matched .Only us eproducts recommended
by Mercedes-Benz. Damage which is caused
by the us eofproducts which have not been
recommended is not covered by the
Mercedes-Benz warranty or goodwil lges- tures. The
yare listed in this Mercedes-Benz
Owner's Manua linthe appropriate section.
Yo uc an identif yservice products approved
by Mercedes-Benz by the following inscrip-
tions on the container:
R MB-Freigab e(e.g. MB-Freigab e229.51)
R MB Approva l(e.g. MB Approva l229.51)
Othe rdesignations or recommendations indi-
cate alevel of quality or aspecification in
accordance with an MB Shee tNum ber(e.g.
MB 229.5) .The yh aven ot necessaril ybeen
approved by Mercedes-Benz.
Othe ride ntifications ,for example:
R 0W -30
R 5W -30
R 5W -40
Further information can be obtaine dfrom any
Mercedes-Benz Service Centre or on the
Interne tath ttp://bevo.mercedes-benz.com. Fuel
Important safety notes G
WARNING
Fue lish ighl yf lammable. If yo uhandlef uel
incorrectly, ther eisariskoff irea nd explo-
sion.
Yo um usta void fire, nake dflames ,creating
sparks and smoking. Switch off the engine
and ,ifa pplicable, the auxiliary heating before
refuelling. G
WARNING
Fuels are poisonous and hazardou stohealth.
There is adanger of injury.
Do not swallo wfuelorl etit come into contact
with skin, eyes or clothing .Donot inhale fuel
vapours. Kee pfuels ou tofthe reach of chil-
dren. Servic
eproducts and capacities
473Technical data
Z

the
rinformation fro many Mercedes-Benz
Service Centre.
Usually yo uwillf indi nformation abou tthe
fuel grade on the pump. If yo ucannot find the
labe lont he petrol pump, as kthe filling sta-
tio ns taff.
i E10 fuel contains up to 10% bioethanol.
Your vehicl eissuitabl efor us ewithE 10
fuel .You ma yrefue lyou rvehicl eusing E10
fuel.
E1 80,E2 50:asatemporary measure, if the
recommended fuel is not available, yo umay
also us eregular unleade dpetrol with an
octane rating of 93 RON/83 MON.
Al lo ther models: asatemporary measure, if
the recommended fuel is not available, you
ma yalsou seregular unleade dpetrol with an
octane rating of 91 RON/82 MON .Thism ay
reduc eengine performance and increase fuel
consumption. Avoi ddriving at full throttle and
sudden acceleration. Never refue lusing fuel
with alower RON/MON.
i In some countries
,the availabl epetrol
ma ynot be sufficiently lo winsulphur .This
fuel can temporarily produce unpleasant
odours, especiall yonshort journeys. As
soon as sulphur-fre efuel(sulphu rcontent
<10p pm)isu sedf or refuelling, the odours
are reduced.
Information on refuelling (Y page201).
AMG vehicles ! Only refuel using super unleade
dpetrol
with at least 98 RON/88 MON that con-
forms to European standard EN 228 or an
equivalent specification.
You can otherwise impair engine output or
damage the engine.
! Premium-grade unleade
dpetrol with an
octane rating of 95 RON/85 MON may be
use dasat emporary measure if the recom-
mended fuel is not available .Thism ay
reduce engine performance and increase
fuel consumption. As much as possible,
avoi ddriving at ful lthrottle. !
Regular unleade
dpetrol with an octane
rating of 91 RON/82.5 MON may also be
use dasat emporary measure if the recom-
mended fuel is not available.
Doing so results in noticeably higher fuel
consumption, and the engine power output is noticeably reduced. Avoid driving at full
throttle.
If only regularu nleadedpetrol with an
octane rating of 91 RON/82.5 MON or
lower is available ,you must have the vehi-
cle adapted to this fuel at aqualified spe-
cialist workshop.
i E10 fuel contains up to 10% bioethanol.
You rvehicle is suitabl efor use with E10
fuel .You may refuel you rvehicle using E10
fuel.
E2 00,E2 50,E4 00,E4 00 4MATIC (only
for certain countries)
! Only refuel using unleaded, sulphur-free
unleade dpetrol with at least 95 RON/
85 MON that conforms to European stand-
ard EN 228 or an equivalent specification.
You coul dotherwise impair engine output
or damage the emission control system.
i In some countries, the available petrol
may not be sufficiently low in sulphur. This
fuel can temporaril yproduce unpleasant
odours, especially on short journeys. As
soon as sulphur-free fuel (sulphur content
<10p pm)isu sedf or refuelling, the odours
are reduced.
Additives ! Operating the engine with fuel additives
added later can lea dtoengine failure. Do
not mix fuel additive swithf uel .Thisd oes
not include additive sfor the remova land
prevention of residue build-up. Petrol must
only be mixed with additive srecommended
by Mercedes-Benz. Observe the instruc-
tions for use in the product description.
More information about recommended
additive scan be obtained from any
Mercedes-Benz Service Centre. Service products and capacities
475Technical data Z

Mercedes-Ben
zrecommends that you use
fuel brands that have additives.
The quality of the fuel available in some coun- tries may not be sufficient. Residuec ould
build up in the injection system as aresult. In
this case, in consultation with aMercedes-
Benz Service Centre, the petrol may be mixed with the cleaning additive recommended by
Mercedes-Benz. Always observe the notes
and mixing ratios specified on the container.
Diesel Fuel grade
G
WARNING
If you mix diesel fuel with petrol, the flash
point of this fuel mixture is lower than that of pure diesel fuel. When the engine is running,
components in the exhaust system may over-
heat unnoticed. There is arisk of fire.
Never refuel with petrol. Never add petrol to
diesel fuel.
! When refuelling, only use diesel fuel that
conforms to the European standard EN 590
or is of equivalent quality. Fuel that does
not conformtoEN5 90 can lead to
increased wear as well as damage to the
engine and exhaust system.
! Do not use the following:
R marine diesel
R heating oil
R bio-diesel
R vegetable oil
R petrol
R paraffin
R kerosene
Do not mix such fuels with diesel fuel and
do not use any special additives. Other-
wise, engine damage may occur.
! Vehicles with diesel particle filters:
in
countries outside the EU, only use low sul-
phur Euro diesel with asulphurc ontent of under 50 ppm
.Otherwise, the emission
control system could be damaged.
! Vehicles without
adiesel particle fil-
ter: in countries where only diesel fuel with
ah igh sulphurc ontent is available, you will
need to carry out your vehicle&#39;s oil change
at shorter intervals. More information
about the interval for oil change can be
obtained from any qualified specialist
workshop.
Usuallyy ou will find information about the
fuel grade on the pump. If you cannot find the
label on the petrol pump, ask the filling sta-
tion staff.
Information on refuelling (Y page 201).
Low outside temperatures
In winter months, diesel fuel with an improved
cold flow quality is available. In Europe, the
EN 590 standard defines various climate-
dependent temperature categories. Malfunc- tions can be avoided by refuelling with diesel
fuel that corresponds to the climatic specifi-
cations outlined in EN 590. At unusually low
outside temperatures, it is possible that the
flow characteristics of the diesel fuel could be insufficient .Accordingly, diesel fuel from
warmer areas may not be suitable for opera-
tion in colder climatic conditions.
i Further information on country-specific
fuel properties and fuel types with low-tem-
perature resistance can be obtained from
oil companies, e.g. at filling stations.
Fuel consumption information H
Environmental note
CO 2(carbon dioxide) is the gas which scien-
tists believe to be principally responsible for
global warming (the greenhouse effect). Your vehicle&#39;s CO 2emissions are directly related to
fuel consumption and therefore depend on: 476
Service products and capacitiesTechnical data

Assuring the purity of AdBlue
®
is particularly
important with respect to avoiding malfunc-
tions in the BlueTEC exhaust ga saftertreat-
ment system.
If AdBlue ®
is pumpe doutof the AdBlue ®
tank,
e.g .during repai rwork, do not us ethisf luid to
refil lthe tank. The purity of the fluid can no
longe rbeg uaranteed.
Capacities Model Total capacity
Al
lm odels 25.5 l
Engine oil
General notes Whe
nhandling engine oil, observe the impor-
tant safety note sonserviceproducts
(Y page 473).
The quality of the engine oi lisdecisive for the
functio nand servic elifeofane ngine.After
extensive tests ,Mercedes-Benz approves
engine oils tha tcorrespond to the current
technica lstandard.
Therefore ,onlyM ercedes-Benz approved
engine oils ma ybeusedinM ercedes-Benz
engines.
Further informatio nontestedand approved
engine oils can be obtained fro many
Mercedes-Benz Service Centre. Mercedes-
Benz recommends tha tyou have the oil
change carrie doutataq uali fied specialist
workshop .Mercedes-Benz approva lisindica-
ted on the oi lcontaine rbythe inscription &#34;MB
Approval &#34;and the corresponding designa-
tion, e.g .MBApproval 229.51.
Yo uc an cal lupano verview of approved
engine oils on the Internet at
http://bevo.mercedes-benz.co mbyenter-
ing the designation, e.g. 229.5.
The table shows which engin eoils have been
approved for your vehicle. Petrol engines:
in certain countries, differ-
ent engin eoils can be used, provided that the
maintenanc eintervals are reduced. For more
information ,please contact aqualified spe-
cialist workshop. Petrol engines MB Approval
All models
229.5
Diesel engines MB Approval
E3
50 CDI 228.51,
229.31 ,229.51 All other models
228.51,
229.31,
229.51 ,229.52 Use only SAE0
W-40orS AE 5W-40 engine oils
for AMG vehicles.
i If the engine oilsl isted in the table are not
available,y ou may add the following engine
oilsu ntil the next oil change:
R vehicles with apetrol engine: MB
Approva l229.1, 229.3 or ACEA A3
R vehicles with adiesel engine: MB
Approva l229.1, 229.3, 229.5 or ACEA
C3
This must only be added once and the
amount must not be greater than 1.0 l.
Ca pacities The following value
srefe rtoano ilchange,
including the oi lfilter. Model Replacement
amount E1
80 6.1 l
E2
00
E2 50 6.3 l478
Servic
eproducts and capacitiesTechnical data

Model Replacement
amount E5
00
E5 00 4MATIC
E3 00 BlueTEC
E3 50 CDI
E3 50 BlueTEC
E3 50 BlueTEC
4MATIC 8.0 l
AMG vehicles
8.5 l
All other models
6.5 l
Additives
!
Do not use any additives with the engine
oil.T his coul ddamage the engine.
Engine oil viscosity Viscosity describes the flow characteristics
of afluid. If an engine oil has ahigh viscosity
rating, it flow sslowly;t he lower the viscosity,
the faster it flows.
Engine oil selection is based on the respective outside temperatures and in accordance with
the SAE classification (viscosity) .The table
show syou which SAE classifications are to be
used. The low-temperature properties of
engine oilsc an be significantly impaired dur-
ing operation due to, for example, ageing or
soot and fuel accretion. It is therefore
strongly recommende dtoobserve regular oil
changes using an approved engine oil with the
appropriate SAE classification. Brake fluid
G
WARNING
The brake flui dcontinuously absorbs mois-
ture from the air. This results in the boiling
point of the brake flui dlowering. If the boiling
point of the brake flui distoo low,v apour
pockets may form when the brakes are sub-
jected to aheavy load. This would impair brak-
ing efficiency. There is arisk of an accident.
Have the brake flui drenewe datthe prescri-
bed intervals.
Comply with the important safety notes for
service products when handling brake fluid
(Y page4 73).
The brake flui dchange interval scan be found
in the Service Booklet.
Only use brake flui dapproved by Mercedes-
Benz according to MB Approva l331.0.
Information about approved brake flui dcan
be obtained at any qualified specialist work-
shop or on the Internet at
http://bevo.mercedes-benz.com.
i Have the brake flui
dregularl yreplaced at
aq ualified specialist worksho pand the
replacement confirmed in the Service
Booklet. Coolant
Important safety notes G
WARNING
If antifreeze comes into contact with hot com- ponents in the engine compartment, it may
ignite. There is arisk of fire and injury.
Let the engine cool downb efore you top up
the antifreeze. Make sure that antifreeze is
not spilled next to the filler neck. Thoroughly
clea nthe antifreeze from components before
starting the engine.
! Only add coolant that has been premixed
with the desired antifreeze protection. You
coul dotherwise damage the engine. Servic
eproducts and capacities
479Technical data Z

Further information on coolants can be
found in the Mercedes-Benz Specifications for Service Products, MB Specifications for Service Products 310.1, e.g. on the Inter-
net at http://bevo.mercedes-benz.com.
Or contact aquali fied specialist workshop.
! Alway
suseasuitabl ecoolant mixture,
eve ninc ountries where hig htemperatures
prevail.
Otherwise, the engine cooling system is not
sufficiently protected from corrosio nand
overheating.
i Have the coolant regularly replaced at a
qualified specialist worksho pand the
replacement confirmed in the Service
Booklet.
Compl ywitht he important safety precautions
for service products whe nhandling coolant
(Y page 473).
The coolant is amixture of water and anti-
freeze/corrosio ninhibitor. It is responsible
for the following:
R anti-corrosion protection
R antifreeze protection
R raising the boiling point
If antifreeze/corrosio ninhibitor is present in
the correct concentration, the boiling point of
the coolant during operation will be approx-
imately 130 †.
The antifreeze/corrosio ninhibitor concentra-
tion in the engine cooling system should:
R be at least 50% .Thisw illp rotect the engine
cooling system against freezing dow nto
approximately -37 †.
R not excee d55% (antifreeze protection
dow nto- 45 †). Hea twillo therwise not be
dissipated as effectively.
Mercedes-Benz recommends an antifreeze/
corrosio ninhibitor concentrate in accord-
ance with MB Specifications for Service Prod- ucts 310.1.
i Whe
nthe vehicle is firs tdelivered ,itisfil-
le dw ithac oolant mixture that ensures adequate antifreeze and corrosio
nprotec-
tion.
i The coolant is checke
datevery mainte-
nance interval at aquali fied specialist
workshop. Windscree
nwasher system
Important safety notes G
WARNING
If windscreen washe rconcentrate comes into
contact with hot components of the engine or
the exhaust system, it can ignite. There is a
ris koff ire and injury.
Make sur ethe windscreen washe rconcen-
trate doe snot come into contact with the filler
neck.
! Do not us
edistille dord e-ionised water in
the washe rfluid reservoir. Otherwise, the
level senso rmay be damaged.
! Only the washe
rfluid sSummerFit and
WinterFit can be mixed. Otherwise, the
spraying nozzles could become blocked.
Compl ywitht he important safety notes for
service products whe nhandling washe rfluid
(Y page 473).
At temperatures above freezing:
X Fil lthe washe rfluid reservoi rwitham ixture
of water and washe rfluid ,e.g. MB Sum-
merFit.
Mix 1partMBS ummerFit to 100 parts water.
At temperatures below freezing:
X Fil lthe washe rfluid reservoi rwitham ixture
of water and washe rfluid ,e.g. MB Winter-
Fit.
For the correct mixing rati orefe rtot he
information on the antifreeze reservoir.
i Add washe
rfluid concentrate, e.g. MB
SummerFit or MB WinterFit, to the washer
fluid al lyea rround. 480
Servic
eproducts and capacitiesTechnical data