MERCEDES-BENZ R320 2008 W251 Owner's Manual
Page 151 of 569
150 Controls in detail
Lighting
Hazard warning flasher
The hazard warning flasher can be
switched on at all times, even with the
SmartKey removed from the starter switch
or with the SmartKey with KEYLESS-GO*
removed from the vehicle.
The hazard warning flasher switches on
automatically when an air bag deploys.
The hazard warning flasher switch is
located on the upper part of the center
console.
1Hazard warning flasher switchSwitching on hazard warning flasher
Press hazard warning flasher
switch1.
All turn signals are flashing.
Switching off hazard warning flasher
Press hazard warning flasher switch1
again.
Interior lighting
1Front left reading lamp, on/off
2Rear interior lighting, on/off
3Automatic interior lighting
4Front interior lighting, on/off
5Front right reading lamp, on/off
6Front right interior lamp
7Reading lamps
8Front left interior lamp
iWith the hazard warning flasher activated
and the combination switch set for either left or
right turn, only the respective left or right turn
signals will operate when the ignition is
switched on.
iIf the hazard warning flasher has been
activated automatically, press hazard warning
flasher switch1 once to switch it off.
Page 152 of 569
151 Controls in detail
Lighting
The controls are located in the overhead
control panel.
Deactivating automatic control
Press switch3.
The interior lighting and the locator
lighting (
page 178) remain switched
off even when you
unlock the vehicle
remove the SmartKey from the
starter switch
open a door
open the tailgateActivating automatic control
Press switch3.
The interior lighting and the locator
lighting (
page 178) come on when
you
unlock the vehicle
remove the SmartKey from the
starter switch
open a door
open the tailgate
The interior lighting switches off after
10 seconds see “Setting interior lighting
delayed shut-off” (
page 180).Manual control
Switching front/rear interior lighting on
and off
Press front/rear interior lighting
switch4 or 2 (
page 150) to switch
on the desired interior light.
Press front/rear interior lighting
switch4 or 2 again to switch off the
respective interior light.
Switching front reading lamps on and off
The front reading lamps are located in the
lower edge of the interior rear view mirror.
Press front reading lamp
switch1or5 (
page 150) to
switch on the desired front reading
lamp.
Press front reading lamp
switch1or5 again to switch off the
respective front reading lamp.
!An interior lamp switched on manually does
not go out automatically.
Leaving an interior lamp switch in the ON
position for extended periods of time with the
engine turned off could result in a discharged
battery.
iThe interior lighting is factory-set to
automatic mode.
iIf a door remains open, the interior lighting
switches off automatically after approximately
5minutes.
Page 153 of 569
152 Controls in detail
Lighting
Switching second-row reading lamps on
and off
The second row reading lamps are located
above the side windows.
Passenger side reading lamp
1Second-row reading lamp
Press on reading lamp 1 where indi-
cated by arrow.
The reading lamp comes on.
Press on reading lamp 1 once more.
The reading lamp goes out.Switching third-row reading lamps* on
and off
The switches for the third-row reading
lamps are located in the rear overhead
control panel.
1Rear right reading lamp, on/off
2Rear left reading lamp, on/off
3Rear left reading lamp
4Rear interior lamp
5Rear right reading lamp
Press rear reading lamp
switch1or2 to switch on the
respective rear reading lamp.
Press rear reading lamp
switch1or2 again to switch off the
respective rear reading lamp.
iThe rear interior lighting is switched on and
off using the switch on the front overhead
control panel (
page 150).
Page 154 of 569
153 Controls in detail
Lighting
Door entry lamps
For better orientation in the dark, the
corresponding door entry lamps will switch
on in darkness when you open a door and
the automatic control is activated.
The door entry lamps will switch off when
the corresponding door is closed.Cargo compartment lamp
The cargo compartment lamp comes on
when the tailgate is opened.
If you leave the tailgate open for an
extended period of time, the cargo
compartment lamp will switch off
automatically after approximately
10 minutes.
iIf you turn the SmartKey in the starter
switch to position0 and switch off the
headlamps, the door entry lamps will remain lit
for approximately 5 minutes.
Page 155 of 569
154 Controls in detail
Instrument cluster
For a full view illustration of the instrument
cluster, see “Instrument cluster”
(
page 26).
1To dim instrument cluster illumination
2Reset button
3To brighten instrument cluster
illumination
The instrument cluster is activated when
you
open a door
switch on the ignition (page 39)
press reset button 2
switch on the exterior lamps
(
page 143)For information on changing the instru-
ment cluster settings, e.g. the language,
see “Instrument cluster submenu”
(
page 174).Adjusting instrument cluster
illumination
Use button 1 or 3 to adjust the illumina-
tion brightness for the instrument cluster.
To brighten illumination
Press and hold button 3 until the
desired level of illumination is reached.
To dim illumination
Press and hold button 1 until the
desired level of illumination is reached.
iOpening a front door or pressing the reset
button without switching on the ignition or the
exterior lighting activates the multifunction
display illumination only for 30 seconds.
Warning!G
No messages will be displayed if either the
instrument cluster or the multifunction
display is inoperative.
As a result, you will not be able to see
information about your driving conditions,
such as speed or outside temperature,
warning/indicator lamps,
malfunction/warning messages or the
failure of any systems. Driving characteris-
tics may be impaired.
If you must continue to drive, do so with
added caution. Contact an authorized
Mercedes-Benz Light Truck Center as soon
as possible.
iThe instrument cluster illumination is
dimmed or brightened automatically to suit
ambient light conditions.
The instrument cluster illumination will also be
adjusted automatically when you switch on the
vehicle’s exterior lamps.
iWith the exterior lighting switched on, the
brightness of the switches in the center console
will also be adjusted when using button 1 or 3.
Page 156 of 569
155 Controls in detail
Instrument cluster
Resetting trip odometer
Make sure you are viewing the trip
odometer display (
page 157).
If it is not displayed, press buttonè
orÿ on the multifunction steering
wheel (
page 158) repeatedly until
the trip odometer appears in the multi-
function display.
Press and hold reset button 2
(
page 154) until the trip odometer is
reset.
Tachometer
The red marking on the tachometer
(
page 29) denotes excessive engine
speed.
To help protect the engine, the fuel supply
is interrupted if the engine is operated
within the red marking.
Outside temperature indicator
The outside temperature is indicated in the
multifunction display (
page 157).
!Avoid driving at excessive engine speeds, as
it may result in serious engine damage that is not
covered by the Mercedes-Benz Limited
Warranty.
Warning!G
The outside temperature indicator is not
designed to serve as an ice-warning device
and is therefore unsuitable for that purpose.
Indicated temperatures just above the
freezing point do not guarantee that the
road surface is free of ice. The road may still
be icy, especially in wooded areas or on
bridges.
Page 157 of 569
156 Controls in detail
Instrument cluster
The outside temperature sensor is located
in the front bumper area. Due to its loca-
tion, the sensor can be affected by road or
engine heat during idling or slow driving.
This means that the accuracy of the dis-
played temperature can only be verified by
comparison to a thermometer placed next
to the sensor, not by comparison to exter-
nal displays (e.g. bank signs etc.).
When moving the vehicle into colder
ambient temperatures (e.g. when leaving
your garage), you will notice a delay before
the lower temperature is displayed.
A delay also occurs when ambient temper-
atures rise. This prevents inaccurate
temperature indications caused by heat
radiated from the engine during idling or
slow driving.
Page 158 of 569
157 Controls in detail
Control system
Control system
The control system is activated as soon as
the SmartKey in the starter switch is
turned to position1 (
page 40) or as
soon as the KEYLESS-GO start/stop
button* is in position1 (
page 41). The
control system enables you to
call up information about your vehicle
change vehicle settings
For example, you can use the control
system to find out when your vehicle is
next due for maintenance service, to set
the language for messages in the instru-
ment cluster display, and much more.
The control system relays information to
the multifunction display.
Multifunction display
1Trip odometer
2Main odometer
3Transmission position indicator
4Current transmission program mode
5Status indicator (outside temperature
or digital speedometer)
For more information on menus displayed
in the multifunction display, see “Menus”
(
page 160).
Warning!G
A driver’s attention to the road and traffic
conditions must always be his/her primary
focus when driving.
For your safety and the safety of others,
selecting features through the multifunction
steering wheel should only be done by the
driver when traffic and road conditions
permit it to be done safely.
Bear in mind that at a speed of just
30 mph (approximately 50 km/h), your
vehicle is covering a distance of
44 feet (approximately 14 m) every second.
Page 159 of 569
158 Controls in detail
Control system
Multifunction steering wheel
The displays in the multifunction display
and the settings in the control system are
controlled by the buttons on the multifunc-
tion steering wheel.1Multifunction display
Operating the control system
2Selecting the submenu or setting
the volume:
Press button
æup/to increase
çdown/to decrease
3Telephone*:
Press button
sto take a call
to dial
to redial
tto end a call
to reject an incoming call
4Moving within a menu:
Press button
jfor next display
kfor previous display
5Menu systems:
Press button
èfor next menu
ÿfor previous menu
6! Voice Control System* on1,
see separate operating
instructions
70 Voice Control System* off1,
see separate operating
instructions
1Vehicles without Voice Control System*: Button
without function.
Page 160 of 569
159 Controls in detail
Control system
Depending on the selected menu, pressing
the buttons on the multifunction steering
wheel will alter what appears in the multi-
function display.
The information available in the multifunc-
tion display is arranged in menus, each
containing a number of functions or sub-
menus.
The individual functions are then found
within the relevant menu (radio or
CD operations under
AUDIO, for example).
These functions serve to call up relevant
information or to customize the settings
for your vehicle.It is helpful to think of the menus, and the
functions within each menu, as being ar-
ranged in a circular pattern.
If you press buttonè orÿ
repeatedly, you will pass through each
menu one after the other.
If you press buttonk orj
repeatedly, you will pass through each
function display, one after the other, in
the current menu.In the
Settings menu, instead of
functions, you will find a number of
submenus for calling up and changing
settings. For instructions on using these
submenus, see “Settings menu”
(
page 170).
The number of menus available in the
system depends on which optional equip-
ment is installed in your vehicle.
The menus are described on the following
pages.