MERCEDES-BENZ SL65AMG 2006 R230 Owner's Manual

390 Practical hintsReplacing SmartKey batteriesSmartKey with KEYLESS-GO*
Replacement battery: Lithium, type
CR 2025 or equivalent.
Remove the mechanical key
(page 385).

Take the battery compartment out of
the SmartKey housing (
page 389).1Battery
2Tilt battery up
3Mechanical key

Using mechanical key3, apply pres-
sure to position 2.
Battery 1 tilts up slightly.

Pull out battery 1 in direction of ar-
row.

Using a lint-free cloth, insert the new
battery under the contact spring with
the plus (+) side facing up.

Return the battery compartment into
the housing until it locks into place.

Slide mechanical key 1 back into the
SmartKey, see “SmartKey”
(page 389).

Check the operation of the SmartKey
with KEYLESS-GO.
iWhen replacing batteries, always re-
place both batteries. The required re-
placement batteries are available at
any authorized Mercedes-Benz Center.

391 Practical hints
Replacing bulbs
Replacing bulbs
Bulbs
Safe vehicle operation depends on proper
exterior lighting and signaling. It is there-
fore essential that all bulbs and lamp as-
semblies are in good working order at all
times.
Correct headlamp adjustment is extremely
important. Have headlamps checked and
readjusted at regular intervals and when a
bulb has been replaced. See an authorized
Mercedes-Benz Center for headlamp ad-
justment.
iIf the headlamps or front fog lamps are
fogged up on the inside as a result of
high humidity, driving the vehicle a dis-
tance with the lights on should clear up
the fogging.
iSubstitute bulbs will be brought into
use when the following lamps malfunc-
tion:

Turn signal lamps


Brake lamps


Parking lamps


Tail lamps
Observe the messages in the multi-
function display (
page 345).

392 Practical hintsReplacing bulbsFront lamps Rear lamps
Lamp
Type
1
Additional turn signal
LED
2
Turn signal lamp
1156 NA
3
Low beam
1
1Vehicles with Bi-Xenon* headlamps: Low beam
and high beam use the same D2S-35W lamp. Do
not replace the Xenon and Bi-Xenon* bulbs your-
self. Contact an authorized Mercedes-Benz Center.
D2S-35 W
4
Xenon headlamps:
High beam, high beam
flasher
H7 (55 W)
Bi-Xenon head-
lamps*:
High beam flasher
H7 (55 W)
Parking and standing
lamps
W 5 W
5
Fog lamp, Corner-illu-
minating front fog
lamp*
HB4 (51 W)
6
Side marker lamp
W 5 W
Lamp
Type
7
Rear fog lamp
(driver’s side only);
replacement
P 21 W
1156/32 cp
8
High mounted brake
lamp
LED
9
Backup lamp;
replacement
P 21 W
1156/32 cp
a
Tail, parking and
standing lamp, side
marker lamp
LED
b
Tail, parking and
standing lamp, brake
lamp
LED
c
License plate lamps
C 5 W
d
Turn signal lamp;
replacement
P 21 W
1156/32 cp

393 Practical hints
Replacing bulbs
Notes on bulb replacement

Only use 12-volt bulbs of the same type
and with the specified watt rating.


Switch the lights off before changing a
bulb to prevent short circuits.


Always use a clean lint-free cloth when
handling bulbs.


Your hands should be dry and free of oil
and grease.


If the newly installed bulb does not
come on, visit an authorized
Mercedes-Benz Center.Have the LEDs and bulbs for the following
lamps replaced by an authorized
Mercedes-Benz Center:


the additional turn signals in the exteri-
or rear view mirrors


the high mounted brake lamp


the brake lamps


the parking lamps and the side marker
lamps in the tail lamp unit


the rear fog lamps


the low beam (Xenon or Bi-Xenon*)
lamps


the front fog lamps


the front side marker lamps
Warning!
G
Bulbs and bulb sockets can be very hot. Al-
low the lamp to cool down before changing
a bulb.
Keep bulbs out of reach of children.
Halogen lamps contain pressurized gas. A
bulb can explode if you:

touch or move it when hot


drop the bulb


scratch the bulb
Wear eye and hand protection.
Because of high voltage in Xenon lamps, it is
dangerous to replace the bulb or repair the
lamp and its components. We recommend
that you have such work done by a qualified
technician.
iHave the headlamp adjustment
checked regularly.

394 Practical hintsReplacing bulbsReplacing bulbs for front lamps
Before you start to replace a bulb for a
front lamp, do the following first:
Turn the exterior lamp switch to posi-
tion M (
page 123).

Open the hood (
page 272).
1Bulb socket for turn signal lamp
2High beam headlamp cover
3Low beam headlamp cover (Xenon or
Bi-Xenon* lamp). Do not remove.4High beam bulbs
5Locking mechanism
6Parking and standing lampsFront turn signal bulb

Turn bulb socket 1 counterclockwise
and pull it out.

Push the bulb into socket 1, turn
socket 1 counterclockwise and re-
move it.

Insert the new bulb in socket 1, push
and turn bulb socket 1 clockwise.

Reinsert bulb socket 1 in lamp and
turn bulb socket 1 clockwise.
Warning!
G
Do not remove the cover for the Xenon or
Bi-Xenon* headlamp. Because of high volt-
age in Xenon and Bi-Xenon* lamps, it is dan-
gerous to replace the bulb or repair the lamp
and its components. We recommend that
you have such work done by a qualified
technician.

395 Practical hints
Replacing bulbs
High beam/ high beam flasher bulbs
Press ends of headlamp cover tab to-
gether and remove high beam head-
lamp cover 2.

Pull the electrical connector off.

Turn locking mechanism 5 counter-
clockwise and take out the bulb.

Insert the new bulb so that the base lo-
cates in the recess on the holder.

Turn locking mechanism 5 clockwise.

Plug the connector onto the bulb.

Align high beam headlamp cover 2
and click it into place.Parking and standing lamp bulbs

Press ends of cover tab together and
remove high beam headlamp cover 2.

Pull out bulb socket 6 with the bulb.

Pull the bulb out of bulb socket 6.

Insert a new bulb in bulb socket 6.

Reinstall bulb socket 6.

Align high beam headlamp cover 2
and click it into place.Additional turn signal lamp bulbs
The additional turn signal lamps in the
exterior rear view mirrors have LEDs.
If a malfunction occurs or LEDs fail to func-
tion, the entire turn signal unit must be re-
placed. Have the turn signal unit replaced
by an authorized Mercedes-Benz Center.
Front side marker lamp bulbs
Since replacing the side marker lamp bulbs
is a technically highly demanding process,
we recommend you have the side marker
lamp bulbs replaced by an authorized
Mercedes-Benz Center.

396 Practical hintsReplacing bulbsReplacing bulbs for rear lamps
Before you start to replace a bulb for a rear
lamp, do the following first:
Turn the exterior lamp switch to posi-
tion M (
page 123).

Open the trunk (
page 108).
Tail lamp unit
1Backup lamp
2Turn signal lamp
3Driver’s side: Rear fog lamp
Passenger’s side: Substitute lamp

Fold the trim to the side and remove it.

Turn the bulb socket counterclockwise
and pull it out.

Gently push the bulb into the socket,
turn it counterclockwise and remove it.

Insert the new bulb and reinstall the
bulb socket.
The bulb socket should audibly click
into place.

Reinstall the trim.License plate lamp
1Screws

Loosen both screws 1.

Remove the license plate lamp.

Replace the bulb.

Reinstall the license plate lamp.

Retighten screws 1.

397 Practical hints
Replacing wiper blades
Replacing wiper blades
Removing wiper blades
Turn SmartKey in starter switch to
position1.

Turn combination switch to wiper
settingII (
page 54).

With wiper arms in the vertical position,
turn SmartKey in starter switch to
position0.
!Never open the hood when the wiper
arms are folded forward.
Hold on to the wiper when folding the
wiper arm back. If released, the force
of the impact from the tensioning
spring could crack the windshield.
Do not allow the wiper arms to contact
the windshield glass without a wiper
blade inserted.
Make sure the wiper blades are proper-
ly installed. Improperly installed wiper
blades may cause windshield damage.
For your convenience, we recommend
that you have this work carried out by
an authorized Mercedes-Benz Center.
!To avoid damage to the hood, the wiper
arms should only be folded forward
when in the vertical position.
Warning!
G
For safety reasons, switch off wipers and re-
move SmartKey from starter switch (vehi-
cles with KEYLESS-GO*: Make sure the
vehicle’s on-board electronics have
status0) before replacing a wiper blade.
Otherwise the wiper motor could suddenly
turn on and cause injury.


398 Practical hintsReplacing wiper blades
Fold the wiper arm forward until it
snaps into place.

Turn wiper blade at a right angle to the
wiper arm.

Slide the wiper blade sideways out of
the retainer.
Installing wiper blades
Slide the wiper blade onto the wiper
arm in opposite direction of arrow.

Rotate the wiper blade into a position
parallel to the wiper arm.

Fold the wiper arm backward to rest on
the windshield. Make sure you hold on
to the wiper when folding the wiper arm
back.


399 Practical hints
Flat tire
Flat tire
Your SL 55 AMG with Performance
Package* and SL 65 AMG are equipped
with a TIREFIT kit.Preparing the vehicle
Park the vehicle in a safe distance from
moving traffic on a hard, flat surface
when possible.

Turn on the hazard warning flashers.

Turn the steering wheel so that the
front wheels are in a straight ahead po-
sition.

Set the parking brake.

Move the gear selector lever to P.
Vehicles with SmartKey:

Turn off the engine (
page 60).

Remove the SmartKey from the starter
switch.Vehicles with KEYLESS-GO*:

Turn off the engine by pressing the
KEYLESS-GO* button on the gear se-
lector lever once (
page 60).

Open the driver’s door (this puts the
starter switch in position 0, same as
with the SmartKey removed from the
starter switch). The driver’s door then
can be closed again.

Have any passenger exit the vehicle at
a safe distance from the roadway.
Sealing tires with TIREFIT
Small tire punctures, particularly those in
the tread, can be sealed with TIREFIT.
TIREFIT can be used in ambient tempera-
tures down to -4°F (-20°C).
iOpen door only when conditions are
safe to do so.
iSL 55 AMG with Performance
Package* and SL 65 AMG only.Warning!
G
Keep TIREFIT away from sparks, open flame
or heat source.
Do not smoke.