MERCEDES-BENZ SL65AMG 2008 R230 Owner's Manual

410 Practical hints
Replacing bulbs
Front lamps Rear lamps
LampType
1 Additional turn signalLED
2Turn signal lamp1156 NA
3Low beam1,2
1Vehicles with Bi-Xenon* headlamps: Low beam
and high beam use the same D2S-35W lamp.
2Vehicles with Bi-Xenon* headlamps: Do not
replace the Xenon and Bi-Xenon* bulbs yourself.
Contact an authorized Mercedes-Benz Center.
D2S-35W
4Xenon headlamp:
High beam, high beam
flasherH7 (55 W)
Bi-Xenon headlamp*:
High beam flasherH7 (55 W)
Parking and standing
lampW 5 W
5Front fog lamp,
Corner-illuminating
front fog lamp*H11 (55 W)
6Side marker lampW 5 W
LampType
7 Rear fog lamp
(driver’s side only)P 21 W
8 High mounted brake
lampLED
9 Backup lampP 21 W
a Tail, parking and
standing lamp, side
marker lampLED
b Brake lampLED
c License plate lampC 5 W
d Turn signal lampPY 21 W

411 Practical hints
Replacing bulbs
Notes on bulb replacement

Only use 12-volt bulbs of the same type
and with the specified watt rating.

Switch the lights off before changing a
bulb to prevent short circuits.

Always use a clean lint-free cloth when
handling bulbs.

Your hands should be dry and free of oil
and grease.

If the newly installed bulb does not
come on, visit an authorized
Mercedes-Benz Center.Have the LEDs and bulbs for the following
lamps replaced by an authorized
Mercedes-Benz Center:

the additional turn signals in the
exterior rear view mirrors

the high mounted brake lamp

the brake lamps

the parking lamps and the side marker
lamps in the tail lamp unit

the rear fog lamps

the low beam (Xenon or Bi-Xenon*)
lamps

the front fog lamps

the front side marker lamps
Replacing bulbs for front lamps
Before you start to replace a bulb for a
front lamp, do the following first:
Turn the exterior lamp switch to
position M (
page 131).
Open the hood (page 282).
1Bulb socket for turn signal lamp
2High beam headlamp cover
3Low beam headlamp cover (Xenon or
Bi-Xenon* lamp). Do not remove.
!Do not replace the LEDs yourself. You could
otherwise damage the LEDs or parts of the
vehicle. Only have the LEDs replaced by an
authorized Mercedes-Benz Center.

412 Practical hints
Replacing bulbs
4High beam bulbs
5Locking mechanism
6Parking and standing lampsFront turn signal bulb
Turn bulb socket 1 (page 411)
counterclockwise and pull it out.
Push the bulb into socket 1, turn
socket 1 counterclockwise and
remove it.
Insert the new bulb in bulb socket 1,
push and turn bulb socket 1 clock-
wise.
Reinsert bulb socket 1 in lamp hous-
ing and turn bulb socket 1 clockwise.High beam/high beam flasher bulbs
Press ends of headlamp cover tab
together and remove high beam head-
lamp cover 2 (
page 411).
Pull the electrical connector off.
Turn locking mechanism 5 counter-
clockwise and take out the bulb.
Insert the new bulb so that the base
locates in the recess on the holder.
Turn locking mechanism 5 clockwise.
Plug the connector onto the bulb.
Align high beam headlamp cover 2
and click it into place.Warning!G
Do not remove the cover for the Xenon or
Bi-Xenon* headlamp. Because of high
voltage in Xenon and Bi-Xenon* lamps, it is
dangerous to replace the bulb or repair the
lamp and its components. We recommend
that you have such work done by a qualified
technician.

413 Practical hints
Replacing bulbs
Parking and standing lamp bulbs
Press ends of headlamp cover tab
together and remove high beam
headlamp cover 2.
Pull out bulb socket 6 with the bulb.
Pull the bulb out of bulb socket 6.
Insert a new bulb in bulb socket 6.
Reinstall bulb socket 6.
Align high beam headlamp cover 2
and click it into place.Additional turn signal lamp bulbs
The additional turn signal lamps in the
exterior rear view mirrors have LEDs.
If a malfunction occurs or LEDs fail to func-
tion, the entire turn signal unit must be re-
placed. Have the turn signal unit replaced
by an authorized Mercedes-Benz Center.Front side marker lamp bulbs
Since replacing the side marker lamp bulbs
is a technically highly demanding process,
we recommend you have the side marker
lamp bulbs replaced by an authorized
Mercedes-Benz Center.

414 Practical hints
Replacing bulbs
Replacing bulbs for rear lamps
Before you start to replace a bulb for a rear
lamp, do the following first:
Turn the exterior lamp switch to
position M (
page 131).
Open the trunk (page 114).
Tail lamp unit
1Backup lamp
2Driver’s side: Rear fog lamp
Passenger’s side: Substitute lamp
3Turn signal lamp
Fold the trim to the side and remove it.
Turn the bulb socket counterclockwise
and pull it out.
Gently push the bulb into the socket,
turn it counterclockwise and remove it.
Insert the new bulb and reinstall the
bulb socket.
The bulb socket should audibly click
into place.
Reinstall the trim.License plate lamp
1Screws
Loosen both screws 1.
Remove the license plate lamp.
Replace the bulb.
Reinstall the license plate lamp.
Retighten screws 1.

415 Practical hints
Replacing wiper blades
Replacing wiper blades
Placing wiper arms in vertical position
Wiper blades in vertical position
Vehicles with SmartKey
Turn SmartKey to starter switch
position1 (
page 40).
Turn combination switch to wiper
settingII (
page 58).
With wiper arms in the vertical position,
turn SmartKey in starter switch to
position0.
Remove SmartKey from starter switch.
Warning!G
For safety reasons, switch off wipers and re-
move SmartKey from starter switch
(vehicles with KEYLESS-GO*: Make sure the
vehicle’s on-board electronics have
status0) before replacing a wiper blade.
Otherwise the wiper motor could suddenly
turn on and cause injury.
Warning!G
Wiper blades are components that are sub-
ject to wear and tear. Replace the wiper
blades twice a year, preferably in the spring
and fall. Otherwise the windows will not be
properly wiped. As a result, you may not be
able to observe surrounding traffic condi-
tions and could cause an accident.
!To avoid damage to the hood:

The wiper arms should only be folded
forward when in the vertical position.

Never open the hood when a wiper arm is
folded forward.
!Hold on to the wiper when folding the wiper
arm back. If released, the force of the impact
from the tensioning spring could crack the wind-
shield.
Do not allow the wiper arms to contact the wind-
shield glass without a wiper blade inserted.
For your convenience, we recommend that you
have this work carried out by an authorized
Mercedes-Benz Center.

416 Practical hints
Replacing wiper blades
Vehicles with KEYLESS-GO*
Turn off the engine (page 64).
With the driver’s door closed, the
starter switch is now in position1.
Turn combination switch to wiper
settingII (
page 58).
With wiper arms in the vertical position,
open the driver’s door.
The starter switch is set to position0,
same as SmartKey removed from
starter switch.
Turn combination switch to wiper
setting0 (
page 58).
Removing wiper blades
Fold the wiper arm forward until it
snaps into place.
Turn wiper blade at a right angle to the
wiper arm.
Slide the wiper blade sideways out of
the retainer.
Installing wiper blades
Slide the wiper blade onto the wiper
arm in opposite direction of arrow.
Rotate the wiper blade into a position
parallel to the wiper arm.
Fold the wiper arm backward to rest on
the windshield. Make sure you hold on
to the wiper when folding the wiper arm
back.
!Do not pull on the wiper blade inserts. They
could tear.
!Make sure the wiper blades are properly
installed. Improperly installed wiper blades may
cause windshield damage.

417 Practical hints
Flat tire
Flat tire
Preparing the vehicle
Park the vehicle in a safe distance from
moving traffic on a hard, flat surface
when possible.
Turn on the hazard warning flashers.
Turn the steering wheel so that the
front wheels are in a straight ahead
position.
Set the parking brake (page 63).
Move the gear selector lever to
position P.
Turn off the engine (page 64).
Have any passenger exit the vehicle at
a safe distance from the roadway.
Vehicles with Smartkey: Remove the
SmartKey from the starter switch.
Vehicles with KEYLESS-GO*: Open the
driver’s door (this puts the starter
switch in position 0, same as with the
SmartKey removed from the starter
switch). The driver’s door then can be
closed again.Mounting the spare wheel
iOpen door only when conditions are safe to
do so.
Warning!G
The dimensions of the spare wheel are dif-
ferent from those of the road wheels. As a
result, the vehicle handling characteristics
change when driving with a mounted spare
wheel. Adapt your driving style accordingly.
The spare wheel is for temporary use only.
When driving with spare wheel mounted, en-
sure proper tire inflation pressure and do
not exceed vehicle speed of 50 mph
(80 km/h).
Drive to the nearest Mercedes-Benz Center
as soon as possible to have the spare wheel
replaced with a regular road wheel.
Never operate the vehicle with more than
one spare wheel mounted.
Do not switch off the ESP
® when a spare
wheel is mounted.

418 Practical hints
Flat tire
Preparing the vehicle
Prepare the vehicle as described
(
page 417).
Turn spare wheel bracket counter-
clockwise to loosen.
Take the spare wheel out of the trunk
(
page 401).
Removing tensioning straps
(vehicles with 19" spare wheel only)
A 19" spare wheel has two tensioning
straps on it that must both be removed be-
fore mounting the spare wheel.1Buckle
2Clip
Press on both clips 2 simultaneously
to release buckle 1.Lifting the vehicle
Prevent the vehicle from rolling away
by blocking wheels with wheel chocks
(not included) or other sizeable
objects.
When changing wheel on a level
surface:
Place one wheel chock or other
sizeable object in front of and
another wheel chock or sizeable
object behind the wheel that is
diagonally opposite to the wheel
being changed.
Always try lifting the vehicle using the
jack on a level surface. However,
should circumstances require you to do
so on a hill, place a wheel chock or
other sizeable object and the other
wheel chock or sizeable object as
follows:
Place wheel chocks or other size-
able objects on the downhill side
blocking both wheels of the axle not
being worked on.
iThe tensioning straps are shown in red for
illustration purposes. The tensioning straps on
the spare wheel of your vehicle are black.iKeep the tensioning straps in a safe place.
You will need them to store the spare wheel in
the trunk after use (
page 402).

419 Practical hints
Flat tire
Take the vehicle tool kit and the jack
out of the storage compartment under
the trunk floor (
page 400).
On wheel to be changed, loosen but do
not yet remove the wheel bolts
(approximately one full turn with
wrench).
The jack support tubes are located behind
the front wheel housings and in front of the
rear wheel housings.
Warning!G
The jack is designed exclusively for jacking
up the vehicle at the jack tubes built into
both sides of the vehicle. To help avoid
personal injury, use the jack only to lift the
vehicle during a wheel change. Never get
beneath the vehicle while it is supported by
the jack. Keep hands and feet away from the
area under the lifted vehicle. Always firmly
set parking brake and block wheels before
raising vehicle with jack.
Do not disengage parking brake while the
vehicle is raised. Be certain that the jack is
always vertical (plumb line) when in use,
especially on hills. Always try to use the jack
on level surface. Be sure that the jack arm is
fully inserted in the jack tube. Always lower
the vehicle onto sufficient capacity jack-
stands before working under the vehicle.
Warning!G
When turning the wheel wrench to loosen
the wheel bolts, make sure you position
hands on the wrench in such a way that you
avoid injury to yourself, such as scraping
your hands against the wheel. Make sure
turning the wheel wrench will not scratch or
damage the wheel rim.