remote control MERCEDES-BENZ SLR CLASS 2007 User Guide

224 Controls in detail
Useful features
Step 9:
Press the “training” button on the ga-
rage door opener motor head unit.
The “training light” is activated.
You have 30 seconds to initiate the
following step.
Step 10:
Return to the vehicle and firmly press,
hold for 2 seconds and release the
programmed signal transmitter button
(2, 3 or4).
Step 11:
Press, hold for 2 seconds and release
same signal transmitter button a
second time to complete the training
process.Step 12:
Confirm the garage door operation by
pressing the programmed signal trans-
mitter button (2, 3 or4).
Step 13:
To program the remaining two signal
transmitter buttons, repeat the steps
above starting with step 3.
Gate operator/Canadian programming
Canadian radio-frequency laws require
transmitter signals to “time-out” (or quit)
after several seconds of transmission
which may not be long enough for the
integrated signal transmitter to pick up the
signal during programming. Similar to this
Canadian law, some U.S. gate operators
are designed to “time-out” in the same
manner.
If you live in Canada or if you are having
difficulties programming a gate operator
(regardless of where you live) by using the
programming procedures, replace step 4
with the following:Step 4:
Press and hold the signal transmitter
button (2, 3 or4). Do not release
this button until it has been success-
fully trained.
While still holding down the signal
transmitter button (2, 3 or4),
“cycle” your hand-held remote control
button6 as follows: Press and hold
button6 for 2 seconds, then release
it for 2 seconds, and again press and
hold it for 2 seconds. Repeat this se-
quence on the hand-held remote con-
trol until the frequency signal has been
learned. Upon successful training, indi-
cator lamp1 will flash slowly and then
rapidly after several seconds.
Proceed with programming step 5 and
step 6 to complete.
iSome garage door openers (or other rolling
code equipped devices) may require you to
press, hold for 2 seconds and release the same
signal transmitter button a third time to
complete the training process.


225 Controls in detail
Useful features
Reprogramming a single signal
transmitter button
To program a device using a signal trans-
mitter button previously trained, follow
these steps:
Switch on the ignition (page 40).
Press and hold the desired signal
transmitter button (2, 3 or4).
Do not release the button.
Indicator lamp1 will begin to flash af-
ter 20 seconds. Without releasing the
signal transmitter button, proceed with
programming starting with step 3.Operation of integrated remote control
Switch on the ignition (page 40).
Select and press the appropriate inte-
grated signal transmitter button (2,
3 or4) to activate the remote
controlled device.
The integrated remote control trans-
mitter continues to send the signal as
long as the button is pressed – up to
20 seconds.
Erasing the integrated remote control
memory
Switch on the ignition (page 40).
Simultaneously press and hold outer
signal transmitter buttons2 and 4,
for approximately 20 seconds, until
indicator lamp1 flashes rapidly. Do
not hold for longer than 30 seconds.
The codes of all three channels are
erased.Programming tips
If you are having difficulty programming
the integrated remote control, here are
some helpful tips:

Check the frequency of the hand-held
remote control5 (typically located on
the reverse side of the remote). The in-
tegrated remote control is compatible
with radio-frequency devices operating
between 280-390 MHz.

Put a new battery in hand-held remote
control5. This will increase the likeli-
hood of the hand-held remote control
sending a faster and more accurate sig-
nal to the integrated remote control.

While performing step 3, hold
hand-held remote control5 at differ-
ent lengths and angles from the signal
transmitter button (2, 3 or4) you
are programming. Attempt varying
angles at the distance of 2 to 5 in
(5 to 12 cm) away or the same angle at
varying distances.
iUpon completion of programming the inte-
grated remote control, make sure you retain the
hand-held remote control that came with the ga-
rage door opener, gate operator or other device.
You may need it for use in other vehicles, for fu-
ture programming of an integrated remote con-
trol, or simply for continued use as a hand-held
remote control to operate the respective device
in other situations.
iIf you sell your vehicle, erase the codes of all
three channels.

226 Controls in detail
Useful features

If another hand-held remote control is
available for the same device, try the
programming steps again using that
other hand-held remote control. Make
sure new batteries are in the hand-held
remote control before beginning the
procedure.

Straighten the antenna wire from the
garage door opener assembly. This
may help improve transmitting and/or
receiving signals.
Floormats*
iCertain types of garage door openers are in-
compatible with the integrated remote control. If
you should experience further difficulties with
programming the integrated remote control,
contact an authorized Mercedes-Benz Center, or
call Mercedes-Benz Customer Assistance
Center (in the USA) at 1-800-FOR-MERCedes, or
Customer Service (in Canada) at
1-800-387-0100.
iUSA only:
This device complies with Part 15 of the
FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interfer-
ence, and
(2) this device must accept any interference re-
ceived, including interference that may
cause undesired operation.
Any unauthorized modification to this device
could void the user’s authority to operate the
equipment.
iCanada only:
This device complies with RSS-210 of Industry
Canada. Operation is subject to the following
two conditions:
(1) This device may not cause interference, and
(2) this device must accept any interference re-
ceived, including interference that may
cause undesired operation of the device.
Any unauthorized modification to this device
could void the user’s authority to operate the
equipment.
Warning!G
When you are using floormats, make sure
there is enough clearance and that the
floormats are securely fastened.
Floormats must always be securely fastened
using eyelets1 and retainer pins2.
Before driving off, check that the floormats
are securely in place and adjust them if
necessary. A loose floormat could slip and
hinder proper functioning of the pedals.
Do not place several floormats on top of
each other as this may impair pedal
movement.

334 Practical hints
What to do if ...
Left displayRight displayPossible cause/
consequencePossible solution
;(USA only)
3(Canada only)
Service brake
Visit
workshopThere are malfunctions, but the
electro-hydraulic brake system
is operating normally.Contact an authorized Mercedes-Benz Center
immediately.
Release
parking brakeYou are driving with the parking
brake set.Release the parking brake (page 49).
2 Brake wearThe brake pads have reached
their wear limit.Have the brake pads replaced as soon as pos-
sible.
!Brake pad thickness must be visually
checked by a qualified technician at the intervals
specified in the Maintenance Booklet.
Excessive load on the brake system causes in-
creased wear of brake pads and brake disks. If
the brake pads have to be replaced multiple
times within one maintenance service interval,
the brake disks must be checked. Observe the
information given in the Maintenance Booklet
and contact an authorized Mercedes-Benz
Center.Warning!G
Have brake pad replacement and other work
on the electro-hydraulic brake system car-
ried out by qualified technicians only. Con-
tact your Mercedes-Benz Center for further
information. The electro-hydraulic brake
system must be deactivated prior to working
on the system. High pressure is intermit-
tently built up in the system as part of its
automatic self-test. In addition, the system
is automatically activated when the vehicle
is unlocked by remote control, when the
driver or passenger door is opened, when
the SmartKey in the starter switch is turned
to position1, when the brake pedal is
depressed or when the parking brake is
released.
Failure to deactivate the system prior to
maintenance will cause brake pistons to
extend and brake fluid to leak, which may
result in injuries (contusions and acid
burns), see “Electro-hydraulic brake sys-
tem” (
page 86).

409 Index
D
Daytime running lamp mode 108
Setting 135
Deep water see Standing water
Defogging, Windshield 194
Defrosting, Front 194
Defrosting, Rear 185
Delayed switch-off
Exterior lamps 136
Interior lighting 137
Department of Transportation see DOT
Differential
Message in the multifunction
display 338
Difficulties
While driving 54
With starting 49
Digital clock see Clock
Digital speedometer 122
Dimensions, Vehicle 387
Direction of rotation, Tires 261
Display elements, Audio system 146Displays
Digital speedometer 122
Maintenance service indicator 292
Multifunction display 117
Outside temperature 116, 122
Symbol messages 327
Text messages 316
Vehicle status messages 128, 314
Distance to empty 140
Distance to empty (range), Trip
computer 140
Door
Control panel 34
Entry lamps 112
Handle, Inside 34
Handle, Outside 38
Locking/unlocking, SmartKey 38, 98
Message in the multifunction
display 352
Opening from inside/outside 38,
101
Remote door unlock, Tele Aid 220
Unlocking in an emergency 356DOT 284
Drinking and driving 235
Driving 45, 50
Abroad 243
Hints, Electro-hydraulic brake
system 88
Hydroplaning 241
In winter 242
Instructions 45, 235
Problems 54
Safety systems 81
Systems 203
Through standing water 243
Tips, Automatic transmission 173
Driving safety systems 81
ABS 81
BAS 83
Electro-hydraulic brake system 86
Electronic traction system 85
ESP
®83
Driving systems
Cruise control 203
Dust cover 228

410 Index
E
Electric air pump 353
Electrical fuses 373
Electrical outlet see Power outlet
Electrical system, Technical data 386
Electro-hydraulic brake system 81, 86,
402
Activation 87
Deactivation 88
Driving hints 88
Emergency operating mode 87
Messages in the multifunction
display 329
Self-check 88, 334
Warning lamp 86
Electronic Stability Program see ESP
®
Emergency calls
911 166
Tele Aid 215
Emergency operations
Automatic transmission (Limp-Home
Mode) 181
Remote door unlock, Tele Aid 220
Trunk lid, Releasing from inside 104
Unlocking the vehicle 355Emergency Tensioning Device see ETD
Emergency, In case of
First aid kit 353
Flat tire 362
Hazard warning flasher 111
Instrument cluster, Indicator
lamps 300
Roadside Assistance 16, 217
Towing the vehicle 370
Emission control 245
Information label 378
System warranties 14
Vacuum line routing diagram
label 378
Engine
Break-in recommendations 234
Cleaning 297
Compartment 250
Malfunction indicator lamp 29, 304
Number 378, 400
Poly-V-belt layout 379
Starting 47
Tachometer 29
Technical data 380
Turning off 56Engine coolant see Coolant
Engine oil 253, 391
Adding 254, 389
Additives 253, 391
Checking level 253
Consumption 253
Filler neck 253
Message in the multifunction
display 339
Recommended engine oils and oil
filter 391
Temperature 29
Oil temperature indicator 307
Viscosity 400
ESP
®81, 83, 400
Messages in the multifunction
display 318
Resetting 318
Warning lamp 83, 300
ETD 74, 400
Safety guidelines 64
Exterior lamp switch 51, 106
Exterior rear view mirrors 44

413 Index
Interior rear view mirror 44
Auto-dimming 182
Interior storage spaces see Storage com-
partments
J
Jacking up the vehicle 362
Jump starting 367
K
Key, Mechanical 355
Key, SmartKey
Battery check lamp 100
Checking the batteries 101
Factory setting 99
Locking/unlocking 98
Locking/unlocking, Global setting 99
Locking/unlocking, Selective
setting 100
Loss of 101
Messages in the multifunction
display 340
Opening and closing the
windows 201, 202
Positions in starter switch 40Remote control 98
Replacing the batteries 357
Turning off the engine 56
Unlocking, Trunk 101
Kickdown 173, 401
Kilopascal 285
Knee air bags 66
L
Labels
Certification 378
Emission control label 378
Vacuum line routing 378
Lamps
Exterior 359
Lamps, exterior
Messages in the multifunction
display 341Lamps, indicator and warning
ABS 29, 302
ABS/ESP
®29, 300
Airbrake 29, 307
Battery, SmartKey 100
Brake 29, 303
Center console 312
Coolant 29, 306
Engine malfunction 29, 304
Engine oil temperature 29, 307
Fog lamps 109
Fuel reserve 29, 307
Gearshift 29, 307
High beam 29
Instrument cluster 300
Low tire pressure telltale 29, 311
PASSENGER AIR BAG OFF 70, 312
Seat belt telltale 29, 308
Seat belts 308–309
SRS 29, 61, 310
Turn signals 29
Language, Setting 133

417 Index
Refrigerant, Air conditioning 391
Refueling 247
Regular checks 248
Remote control, SmartKey 98
Remote door unlock, Tele Aid 220
Replacing bulbs 359
Reporting safety defects 22
Research Octane Number see RON
Reset button, in Instrument cluster 114,
292
Residual heat utilization 197
Restraint systems 60
Air bags 60, 62
Child restraints 60
Children in the vehicle 75
Emergency Tensioning Device
(ETD) 60, 74
Seat belts 60, 71
Reverse gear position, Automatic
transmission 169
Rims 285, 381
Roadside Assistance 16, 217
RON 247, 402
Roof rack 230S
Safety
Driving safety systems 81
Occupant 60
Reporting defects 22
Safety belts see Seat belts
Seat belt force limiter 74
Seat belts 60
Children in the vehicle 75
Fastening seat belts 45
Message in the multifunction
display 352
Proper use of 46
Safety guidelines 64
Telltale 308
Warning lamp 308–309
Seating capacity 263
Seats 41
Selector lever see Gear selector lever
Self-test
Lamps in the instrument cluster 300
OCS 71
Tele Aid 215Service and warranty information 14
Service intervals see Service indicator
Service life
Tires 260
Vehicle batteries 256
Service see Maintenance
Service, Parts 376
Settings
Control system menus 120
Control system submenus 121
Factory, SmartKey 99
Individual, Vehicle 129
Menus and submenus 119
Resetting to factory settings, Control
system 129
Selective, SmartKey 100
Time 133
Shift program mode selector switch, Auto-
matic transmission 175
Shifting, Automatic transmission 169
Side air vents 31