MITSUBISHI ENDEAVOR 2004 Service Repair Manual
Page 161 of 3870
Fig. 93: Checking Junction Block Connectors C
-214 And C
-215
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
2004 Mitsubishi Endeavor LS
2004 BRAKES Anti-Lock Braking System (ABS) - Endeavor
Page 162 of 3870
Joint connector C-04
Fig. 94: Checking Joint Connector C
-04
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
G-sensor connector C-23
2004 Mitsubishi Endeavor LS
2004 BRAKES Anti-Lock Braking System (ABS) - Endeavor
Page 163 of 3870
Fig. 95: Checking G
-Sensor Connector C
-23
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Check the connectors, for loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Are the connectors and terminals in good condition?
YES: Open or short circuit may be present in the G-sensor power supply
lines. Repair the wiring harness between G-sensor connector C-23
terminal 1 and junction block connector C-215 terminal 2. Then go to Step
13 .
NO: Repair or replace the damaged component(s). Then go to Step 13 .
STEP 9. Check the following connectors.
AB
S-ECU connector A-02
2004 Mitsubishi Endeavor LS
2004 BRAKES Anti-Lock Braking System (ABS) - Endeavor
Page 164 of 3870
Fig. 96: Checking ABS
-ECU Connector A
-02
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
G-sensor connector C-23
2004 Mitsubishi Endeavor LS
2004 BRAKES Anti-Lock Braking System (ABS) - Endeavor
Page 165 of 3870
Fig. 97: Checking G
-Sensor Connector C
-23
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Check the connectors, for loose, corroded or damaged terminals, or terminals
2004 Mitsubishi Endeavor LS
2004 BRAKES Anti-Lock Braking System (ABS) - Endeavor
Page 166 of 3870
pushed back in the connector.
Q: Are the connectors and terminals in good condition?
YES: Go to Step 10.
NO: Repair or replace the damaged component(s). Then go to Step 13 .
STEP 10. Check the following harness wires.
The wire between ABS-ECU connector A-02 (terminal 8) and G-sensor
connector
C-23
(terminal 3
)
2004 Mitsubishi Endeavor LS
2004 BRAKES Anti-Lock Braking System (ABS) - Endeavor
Page 167 of 3870
Fig. 98: Checking ABS
-ECU Connector A
-02
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
2004 Mitsubishi Endeavor LS
2004 BRAKES Anti-Lock Braking System (ABS) - Endeavor
Page 168 of 3870
Fig. 99: Checking G
-Sensor Connector C
-23
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
The wire between AB
S-ECU connector A-02
(terminal 15
) and G-sensor
2004 Mitsubishi Endeavor LS
2004 BRAKES Anti-Lock Braking System (ABS) - Endeavor
Page 169 of 3870
connector C-23 (terminal 2)
Q: Is any harness wire damaged?
YES: Repair the harness wire. Then go to Step 13 .
NO: Go to Step 11.
STEP 11. Recheck for diagnostic trouble code after the G-sensor is
replaced.
Replace the G-sensor, and check whether DTC C1381, C1382 or C1383 is
reset.
1. Replace the G-sensor.
2. Connect scan tool MB991958 to the data link connec
tor. CAUTION: To prevent damage to scan tool MB991958,
always turn the ignition switch to the
"LOCK" (OFF) position before connecting or
disconnecting scan tool MB991958.
2004 Mitsubishi Endeavor LS
2004 BRAKES Anti-Lock Braking System (ABS) - Endeavor
Page 170 of 3870
Fig. 100: Connecting Scan Tool MB991958 To Data Link Connector
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
2004 Mitsubishi Endeavor LS
2004 BRAKES Anti-Lock Braking System (ABS) - Endeavor