start stop button MITSUBISHI iMiEV 2012 1.G Owners Manual

General information/Charging
1-25
1
NOTE
When the regular charge connector is connected to the
charge port, the charging indicator is blinking. When
charging is started, the charging indicator is illuminated.

The charge level for main drive lithium-ion battery can be
checked with the energy level gauge (I) on the instrument
cluster.
Refer to “Energy level gauge” on page 3-69.10. Charging is complete when the charging indicator turns
off. Pull out the regular charge connector while pressing
the button (J).
NOTE
Charging can be stopped half way. In this case, pull out
the regular charge connector while pressing the button.
I
WA R N I N G
!
After charging, disconnect the charge connector
completely from the charge port. If the charge con-
nector remains partially engaged with the latch
unlocked, the electric motor switch can be turned to
the “START” position and the vehicle can be moved.
J
BK0140800US.book 25 ページ ２０１１年９月２９日　木曜日　午後３時２８分

General information/Charging
1-39
1
Regular charging is
discontinued.There is no power coming from
the outlet.There may have been a electrical power failure, or the breaker may have
failed.Charging will resume when the power source is reset.
The EV charging cable has been
disconnected.Check that the EV charging cable has not been disconnected.
The button on the regular charge
connector has been pressed.If the charge connector button is pressed for a long period of time, charg-
ing will be stopped. Start the charging procedure again.
The temperature of the main
drive lithium-ion battery is too
hot or too cold to charge.Confirm the main drive lithium-ion battery temperature.
Refer to “Cautions and actions to deal with intense heat” on page 1-10
and “Cautions and actions to deal with intense cold” on page 1-12.
Charging is stopped by the regu-
lar charge timer.Charging will stop depending on the timer function setting of the regular
charge device. If you need to charge the main drive lithium-ion battery
more, start the charging procedure again.
Quick charging can-
not be started.The charge connector is not con-
nected correctly and/or not
locked.Check that the charge connector is connected correctly and that it is
locked.
The self-diagnostic function of
the quick charge device returns a
negative result.There is a possibility that the vehicle has a malfunction. Stop charging
and contact a certified i-MiEV dealer.
The power switch of the quick
charger is off.Check the power switch of the quick charger.
Symptom
Possible cause
Possible solution
BK0140800US.book 39 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Seat and restraint systems
2-17
2
NOTE
With the exception of the seat belt for the driver, the seat
belts in all other seating positions are equipped with an
Automatic Locking Retractor (ALR) function. If you pull
the seat belt fully out of the retractor, the retractor will
switch to its ALR child restraint installation function (see
page 2-31).
When the ALR function has been activated, the seat belt
will only retract. If this happens, let the belt fully retract,
then pull the seat belt back out, repeating steps 1 through
4.
5. To release the belt, press the button on the buckle and
allow the belt to retract.
If the belt does not retract smoothly, pull it out and check
for kinks or twists in the webbing. Then make sure it
remains untwisted as it retracts.
Driver’s seat belt reminder/warning light
N00418400371
A tone and warning light are used to remind the driver to fasten
the seat belt.
If the electric motor switch is turned to the “ON” position with-
out the driver’s seat belt being fastened, a warning light will
come on, and a tone will sound for approximately 6 seconds to
remind you to fasten your seat belt.
If the seat belt remains unfastened approximately 1 minute
later, the warning light will flash and the tone will sound inter-
mittently for approximately 90 seconds when the vehicle is
driven.
If the seat belt subsequently remains unfastened, the warning
light and tone will issue further warnings each time the vehicle
starts moving from a stop. And if the driver unfastens the seat
WA R N I N G
!
Be sure the lap belt portion fits snugly and is worn
as low as possible across the hips, not around the
waist. Failure to follow this instruction will increase
the risk of serious injury or death in the event of an
accident.
Be sure the seat belt webbing is not twisted when
worn. Twisted webbing may adversely affect seat
belt performance.
BK0140800US.book 17 ページ ２０１１年９月２９日　木曜日　午後３時２８分

3-66 Features and controls
3
Dash lights brightness indicator
N00572600019
Each time you press the dash lights illumination button (B), the
brightness of the instruments changes.
NOTE
You can adjust to 4 different levels for when the parking
lights or headlights are illuminated and 4 for when they
are not.

If you press and hold the button for longer than about 1
second, the brightness automatically scrolls through its
different levels, and stops scrolling when you release the
button. Select your desired level of brightness.

When the combination headlights and dimmer switch is in
the “AUTO” position, the meter illumination switches
automatically to the adjusted brightness, depending on the
brightness outside the vehicle.

The brightness level of the instruments is stored when the
electric motor switch is turned off.

If the 12V starter battery is disconnected for a long time,
these level of brightness will be reset.
A- Brightness display
B- Dash lights illumination button
Bright Dim
BK0140800US.book 66 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Features and controls
3-97
3
Speaker enrollment function
N00564700011
The Bluetooth
® 2.0 interface can use the speaker enrollment
function to create a voice model for one person per language.
This makes it easier for the Bluetooth
® 2.0 interface to recogn-
ise voice commands said by you.
You can turn a voice model registered with the speaker
enrollment function on and off whenever you want.
Speaker enrollment
N00564800070
It takes about 2 to 3 minutes to complete the speaker
enrollment process.
To ensure the best results, run through the process while in the
driver’s seat, in an environment that is as quiet as possible
(when there is no rain or strong winds and the vehicle windows
are closed). Please turn off your phone while in speaker
enrollment to prevent interruption of the process.
Use the following procedure for speaker enrollment.
1. Stop your vehicle in a safe area, put the selector lever in
the “P” (PARK) position, and then pull the parking brake
lever.NOTE
Speaker enrollment is not possible unless the vehicle is
parked. Make sure you park the vehicle in a safe area
before attempting speaker enrollment.
2. Press the SPEECH button.
3. Say “Voice training.”4. The voice guide will say “This operation must be per-
formed in a quiet environment while the vehicle is
stopped. See the owner’s manual for the list of required
training phrases. Press and release the SPEECH button
when you are ready to begin. Press the HANG-UP button
to cancel at any time.”
Press the SPEECH button to start the speaker enrollment
process.
NOTE
If you do not start the speaker enrollment process within 3
minutes after pressing the SPEECH button, the speaker
enrollment function will time out.
The voice guide will say “Speaker enrollment has timed
out.” The system will then beep and the voice recognition
mode will be deactivated.
5. The voice guide will prompt for phrase 1. Repeat the cor-
responding phrase listed in table “Enrollment commands”
on page 3-116.
The system will register your voice and then move on to
the registration of the next command. Continue the pro-
cess until all phrases have been registered.NOTE
To repeat the most recent voice training command, press
and release the SPEECH button.

If you press the HANG-UP button anytime during the pro-
cess, the system will beep and stop the speaker enrollment
process.
BK0140800US.book 97 ページ ２０１１年９月２９日　木曜日　午後３時２８分

5-22 Comfort controls
5
To listen to the radio
N00735000913
1. Press the POWER button until it beeps to turn the audio
system ON and OFF. The system turns on in the last mode
used.
Press the RADIO button to turn ON the radio.
2. Press the RADIO button to select the desired band
(AM/FM1/FM2).
3. Press the SEEK button to tune to a station, or press the
MEMORY button either or to tune in to a station
memorized.
Refer to “Automatic tuning”, “Manual tuning” or “To
enter frequencies into the memory”.Automatic tuningAfter pressing the SEEK button, a receivable station will be
automatically selected and reception of the station will begin.
SCAN function
Press the SCAN button. The radio will tune consecutively to
each available station for about 5 seconds per station. If you
want to stop scanning, press the SCAN button again.
The frequency display of the current station flashes once per
second during SCAN.Manual tuningThe frequency changes every time the SEEK button is pressed.
Press the button to select the desired station.To enter frequencies into the memoryAs many as 6 AM and 12 FM stations can be entered into the
memory.To store a frequency in the memory, follow these steps:
1. Press the SEEK button to tune to the frequency you wish
to keep in the memory.
2. Press the MEMORY button either or until it beeps.
The sound will be momentarily interrupted while the fre-
quency is being entered into the memory.
3. To recall a frequency that has been saved in memory,
press the MEMORY button briefly for no longer than
about 1 second.
NOTE
Disconnecting the 12V starter battery cables erases all the
radio station settings stored in the memory.
BK0140800US.book 22 ページ ２０１１年９月２９日　木曜日　午後３時２８分

5-24 Comfort controls
5
To listen to a CD
N00735501074
To set a disc1. Press the POWER button until it beeps to turn the audio
system ON and OFF. The system turns on in the last mode
used.
2. Insert the disc with the label facing up.
When a disc is inserted, the CD indicator will come on
and the CD player will begin playing even if the radio is
being used. The CD player will also begin playing when
the CD button is pressed with a disc set in the CD player
or in the disc loading slot, even if the radio is being used.NOTE
For information concerning the adjustment of volume and
tone, refer to “To adjust the volume” on page 5-19 and
“To adjust the tone” on page 5-20.

8 cm compact disc cannot be played on this CD player.

For information concerning the handing of the compact
discs, refer to “Handling of compact discs” on page 5-38.To eject a discWhen the eject button is pressed, the disc automatically stops
and is ejected. The system automatically switches to radio
mode.NOTE
If you do not remove an ejected disc before 15 seconds
have elapsed, the disc will be reloaded.
To listen to a music CDPush the CD button if a disc is already in the CD player. The
audio system will enter CD mode and start playback. The track
number and the playing time will appear on the display. The
tracks in the disc will be played consecutively and continu-
ously.
BK0140800US.book 24 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Comfort controls
5-29
5
To find the start of each track on a disc for playback
N00771900017
Press the SCAN button. “SCAN” will appear on the display
and the CD player will play back the first 10 seconds of each
track on the selected disc (music CDs only) or the currently
selected folder (MP3 CDs only).
The track number will blink while the scan mode is selected.
To stop the scan mode, press the SCAN button again.NOTE
Once all tracks on the disc (music CDs only) or the cur-
rently selected folder (MP3 CDs only) have been scanned,
playback of the disc will restart from the beginning of the
track that was playing when scanning started.

With a disc that contains both CD-DA and MP3 files, the
scan mode causes only files of the same format (CD-DA
only or MP3 files only) to be played.
CD text and MP3 title display
N00752100166
This audio system can display CD text and MP3 titles includ-
ing ID3 tag information.
CD text
The audio system can display disc and track titles for discs
with converted disc and track title information. Press the DISP
button repeatedly to make selections in the following sequence:
disc name → track name → normal display mode.NOTE
The display can show up to 11 characters. If a disc name
or track name has more than 11 characters, press the
PAGE button to view the next 11 characters.

When there is no title information to be displayed, the dis-
play shows “NO TITLE”.

Characters that the audio system cannot display are shown
as “ ”.
MP3 title
The audio system can display folder and track titles for discs
with converted folder and track information. Press the DISP
button repeatedly to make selections in the following sequence:
folder name → track name → normal display mode.
BK0140800US.book 29 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Comfort controls
5-41
5 Clock
(if so equipped)
N00755000124
The time is displayed when the electric motor switch is in the
“ON” or “ACC” position.To set the time1. Press and hold the clock button and the clock display
flashes.
2. Press the SEEK button to adjust the “hours” digit.
If you keep pressing the button, fast-forward begins.3. When the “hours” digit is adjusted, press the clock button
to flash the “minutes” digit.
Press the SEEK button to adjust the “minutes” digit.
If you keep pressing the button, fast-forward begins.
4. When the time is set, press the clock button to stop the
clock display from flashing.
NOTE
Reset the time after the 12V starter battery terminals are
disconnected and reconnected.

Seconds do not appear in the clock display, but after
adjusting the “minutes” setting, the clock begins to oper-
ate from 0 seconds.
A- Clock button
B- SEEK (clock adjustment up) button
C- SEEK (clock adjustment down) button
BK0140800US.book 41 ページ ２０１１年９月２９日　木曜日　午後３時２８分