MITSUBISHI L200 2020 Owner's Manual (in English)

D- “CANCEL” switch
Used to deactivate the set speed driving.NOTEz When operating the cruise control switches,
press the cruise control switches correctly. The set speed driving may be deactivated
automatically if two or more switches of the
cruise control are pressed at the same time.To activate
1. With the ignition switch in the “ON” po-
sition or the operation mode in ON, press the CRUISE CONTROL ON/OFFswitch (A) to turn on the cruise control.
The indication display in the meter clus- ter will come on.
Indicator display
2. Accelerate or decelerate to your desired
speed, then push down and release the “SET -” switch (B) when the indicator
display is illuminated. The vehicle will then maintain the desired speed. The “SET” indicator appears on the informa-tion display in the meter cluster.
NOTEz When you release the “SET -” switch (B),
the vehicle speed will be set.To increase the set speed
There are 2 ways to increase the set speed.
RES + switch
Push up and hold the “RES +” switch (C)
while driving at the set speed, and your speed will then gradually increase.
When you reach your desired speed, release
the switch. Your new cruising speed is now set.
To increase your speed in small amounts, push up the “RES +” switch (C) for less than
approximately 1 second and release it.
Each time you push up the “RES +” switch
(C), your vehicle will go approximately
1.6 km/h (1 mph) faster.
Cruise control*
6-812.7(20(1Starting and driving6

Accelerator pedal
While driving at the set speed, use the accel-
erator pedal to reach your desired speed and
then push down the “SET -” switch (B) and release the switch momentarily to set a new
desired cruising speed.
To decrease the set speed
There are 2 ways to decrease the set speed.
SET - switch
Push down and hold the “SET -” switch (B) while driving at the set speed, and your speed
will slow down gradually.
When you reach your desired speed, release
the switch. Your new cruising speed is now
set.
To slow down your speed in small amounts, push down the “SET -” switch (B) for less
than approximately 1 second and release it. Each time you push down the “SET -” switch
(B), your vehicle will slow down by approxi- mately 1.6 km/h (1 mph).
Brake pedal
While driving at the set speed, use the brake
pedal, which disengages the cruise control,
then push down the “SET -” switch (B) and
release the switch momentarily to set a new desired cruising speed.Cruise control*
6-822.7(20(1Starting and driving6

To temporarily increase or de-crease the speed
To temporarily increase the speed
Depress the accelerator pedal as you would
normally. When you release the pedal, you will return to your set speed.
To temporarily decrease the speed
Depress the brake pedal to decrease the
speed. To return to the previously set speed, push up the “RES +” switch (C).
Refer to “To resume the set speed” on page
6-84.To deactivate
The set speed driving can be deactivated as follows:
z Press the CRUISE CONTROL ON/OFF
switch (A) (Cruise control will be turned off.)
z Press the “CANCEL” switch (D).
z Depress the brake pedal.
The set speed driving is deactivated automat-
ically in any of the following ways.
z When you depress the clutch pedal (on
vehicles with M/T).
z When your speed slows to approximate-
ly 15 km/h (9 mph) or more below the set speed because of a hill, etc.
z When your speed slows to approximate-
ly 40 km/h (25 mph) or less.
z When the Active Stability & Traction
control (ASTC) starts operating.
Refer to “Active Stability & Traction
Control (ASTC)” on page 6-76.
Cruise control*
6-832.7(20(1Starting and driving6

:ARN,NGzOn vehicles with
A/T, although the set
speed driving will be deactivated when shifting to the “N” (NEUTRAL) position,
never move the selector lever to the “N” (NEUTRAL) position while driving.
You would have no engine braking and
could cause a serious accident.
Also, the set speed driving may be deactiva-
ted as follows:
z When the engine speed rises and ap-
proaches the tachometer's red zone (the red-coloured part of the tachometer di- al).
CAUT,ONz When the set speed driving is deactivated
automatically in any situation other than those listed above, there may be a systemmalfunction.
Press the CRUISE CONTROL ON/OFF switch to turn off the cruise control and have your vehicle inspected by a MITSUBISHI
MOTORS Authorized Service Point.To resume the set speed
If the set driving speed is deactivated by the
condition described in “To deactivate” on page 6-83, you can resume the previously set
speed by pushing up the “RES +” switch (C)
while driving at a speed of approximately 40 km/h (25 mph) or higher. The “SET” indi-
cator appears on the information display in the meter cluster.
Under either of the following conditions, however, using the switch does not allow you
to resume the previously set speed. In these
situations, repeat the speed setting procedure:
z The CRUISE CONTROL ON/OFF
switch is pressed.
z The ignition switch is turned OFF or the
operation mode is put in OFF.
z Indication lamp go off.
Speed Limiter*
The Speed Limiter is a driver assist function to prevent from exceeding the speed set by
driver while engine power control.CAUT,ONz Because the system does not use service
brake (hydraulic brake), the vehicle speed may exceed the set speed on the downhill.
If a driver wants to keep the vehicle speed in such a situation, he/she must put on a servicebrake or downshift.NOTEz If the clutch pedal (
M/T) is depressed, the
Speed Limiter does not activate.
If the vehicle speed exceeds the set speed
(approximately 3 km/h), the indicator will
blink in the combination meter.
If the vehicle speed exceeds the set speed ap-
proximately +3 km/h more for approximately 5 seconds after the indicated alert message,
the beep alert sounds for approximately 10 seconds at the most.
While running without alert message, if you
decrease the set speed and vehicle speed is more than set speed approximately +3 km/h, alert message is displayed but beep alert is
delayed.
Speed Limiter*
6-842.7(20(1Starting and driving6

In this case, when vehicle speed keeps ex-ceeding set speed approximately +3 km/h forapproximately 30 seconds after the alert mes-
sage is appeared, beep alert is sounded for approximately 10 seconds at the most.
If the vehicle speeds decreases less than set
speeds after the alert message is appeared, the message is disappeared. When beep alert is sounding, the beep alert also goes off.NOTEz However, this gives priority to audio and
visual signal of safety reasons or driver’s de-mand.
z If the set speed is too lower based on current
shift position, the Speed Limiter may not
limit the vehicle speed to prevent engine stall.Speed Limiter control switches
There are four switches which relate to the
Speed Limiter on the steering wheel.
A-SPEED LIMITER ON/OFF switch
To turn on/off the Speed Limiter.
B- “SET -” switch
To set the current vehicle speed to a set speed decrease the set speed.
C- “RES +” switch
To resume the Speed Limiter with set speed
memorized or increase the set speed.
D- “CANCEL” switch
To cancel the Speed Limiter.
NOTEz Press the switch one by one.NOTEzThe Speed Limiter may be cancelled auto-
matically, if two or more switches are press-
ed at the same time.Speed Limiter information on
the multi information display area
The Speed Limiter information is displayed
on the multi information display area in the
combination meter.
A-Control state
There are three control states as below.
Speed Limiter*
6-852.7(20(1Starting and driving6

LIMIT OFF
When the Speed Limiter is in STAND-
BY, the vehicle speed can exceed the set speed
LIMIT
When the Speed Limiter is in operation.
The vehicle is controlled in order not to exceed the set speed.
OVER LIMIT
When the vehicle speed is exceeding the
set speed by more than approximately 3
km/h.
B-SPEED LIMITER ON indication
When the Speed Limiter is started up, the
Speed Limiter’s symbol is appeared.
C-Set speed
Set speed is appeared if it is stored.To start up
First of all, press the ON/OFF switch in order to power up the Speed Limiter when the igni-
tion switch in the “ON”, position or the oper-
ation mode in ON,
The Speed Limiter indication will be ap-
peared in the combination meter.
To activate
Accelerate or decelerate to your desired
speed, and push down the “SET -” switch (B). The Speed Limiter memorizes the cur-
rent vehicle speed when you release the “SET
-” switch (B). Now, the Speed Limiter starts controlling in order not to exceed the set speed.
If the current vehicle speed is lower than ap-proximately 30 km/h (19 mph) (settable min- imum speed), the set speed is set at approxi-
mately 30 km/h (19 mph).
The set speed is displayed in the combination meter.
And, control state “LIMIT” is displayed in
the combination meter.
To increase the set speedBy using the “RES +” switch
Push up the “RES +” switch continuously.

Then the set speed displayed in the combina- tion meter is gradually increased.
If the set speed reaches your desired speed, release the “RES +” switch (C).
The set speed is increased each approximate- ly 5 km/h (3 mph) per approximately 0.5 sec-
ond.
If a driver wants to increase the set speed a
little, push up “RES +” switch for less than approximately 0.5 second and release it.
The set speed is increased 1 km/h each taps.
Speed Limiter*
6-862.7(20(1Starting and driving6

By using the “CANCEL”switch, the accelerator pedal and the “SET -” switch
Press the “CANCEL” switch (D) to deacti-
vate the Speed Limiter.
Control state “LIMIT” is disappeared and
change control state “LIMIT OFF” in the combination meter.
Accelerate to driver’s desired vehicle speed
and push down “SET -” switch (B) and re-
lease.
Control state “LIMIT” is displayed again and the set speed is updated.
To decrease the set speed

By using the “SET -” switch
Push down the “SET -” switch (B).

Then the set speed displayed in the combina- tion meter is gradually decreased.
If the set speed reaches to your desired speed,
release the “SET -” switch (B).
The set speed decreases approximately
5 km/h (3 mph) per approximately 0.5 sec- ond.
If a driver wants to decrease the set speed a
little, press the “SET -” switch (B) for less
than approximately 0.5 second and release it.
The set speed is decreased 1 km/h each taps.
Speed Limiter*
6-872.7(20(1Starting and driving6

By using the “CANCEL”switch, the service brake and the “SET -” switch
Press the “CANCEL” switch (D) to deacti-
vate the Speed Limiter.
Control state “LIMIT” is disappeared and
change control state “LIMIT OFF” in the combination meter.
Decelerate to driver’s desired speed and push
down “SET -” switch (B) and release.
The Speed Limiter indication is displayed
again and the set speed is updated.
To increase the vehicle speed
temporarily
A driver can temporarily accelerate for emer-
gency use.

The Speed Limiter is temporarily deactiva- ted, and the vehicle speed can be increased.
The Speed Limiter will resume when the ve-
hicle speed goes down to enough less than the set speed.
Put on an accelerator pedal to the pedal
stroke end. (over a detent that makes pedal reaction force bigger before pedal stroke end)
CAUT,ONz There is a possibility for the Speed Limiter
to allow abrupt acceleration corresponding
to accelerator pedal position. So be careful
of the abrupt acceleration.
If vehicle speed exceeds set speed approxi-
mately +3 km/h, alert messages are appeared in the combination meter.
Speed Limiter*
6-882.7(20(1Starting and driving6

CAUT,ONzBe careful about over speed.NOTEzA driver can change the set speed during this
emergency use.To deactivate
Use whichever following ways to deactivate.
z Press the “CANCEL” switch
z Press the Speed Limiter ON/OFF switch
CAUT,ONzThere is a possibility for the Speed Limiter
to allow abrupt acceleration corresponding
to accelerator pedal position when the Speed Limiter is deactivated. Be careful.NOTEz If the Speed Limiter is cancelled by other
states, it may be a system malfunction.
Stop using the Speed Limiter and turn off
the Speed Limiter. Have your vehicle in-
spected by a MITSUBISHI MOTORS Au-
thorized Service Point.To resume
The Speed Limiter memorizes the set speed
when the system has been deactivated, the Speed Limiter can resume by pushing up the
“RES +” switch (C).
However, the Speed Limiter immediately
starts controlling and the vehicle decreases as if an accelerator pedal is closed fully, whenthe vehicle speed is higher than the set speed.
CAUT,ONz There is a possibility to occur jerk, depend-
ing on a running resistance. Be careful.Forward Collision
Mitigation system (FCM)*
The Forward Collision Mitigation System (FCM) uses a sensor (A) to determine the
distance and relative speed to a vehicle and a pedestrian in front. When your vehicle is ap-
proaching a vehicle or a pedestrian straight- ahead in your path and the FCM judges that
there is the risk of a collision, the system gives audible and visual warnings (forward
collision warning function), increases the
brake fluid pressure (FCM brake prefill func- tion), and also provides braking force assis-
tance when you depress the brake pedal (FCM brake assist function) to avoid frontal
collision.
When the risk of collision increases more, the
system causes the brakes to work moderately to encourage you to apply brakes. If the sys-tem judges that a potential collision is immi- nent, it initiates emergency braking to miti-
gate collision-caused damages or to avoid possible collision (FCM braking function).Stop lamps are illuminated during automatic
braking.
Forward Collision Mitigation system (FCM)*
6-892.7(20(1Starting and driving6

If you turn the FCM ON/OFF, the Ultrasonicmisacceleration Mitigation System (UMS) al- so turns ON/OFF at the same time. (Vehicles
equipped with the UMS):ARN,NGz A driver is responsible for driving safely.
The FCM is the system to mitigate colli- sion- caused damages or to avoid colli- sions as much as possible.
The system is not intended to compensate for driver