clock MITSUBISHI LANCER 2016 8.G Owners Manual

Filling the fuel tank3-4
General information
3
Front-wheel drive vehicles: 15.5 gal (59.0 L)All-wheel drive vehicles: 14.5 gal (55.0 L)1.Before filling with fuel, stop the engine.2.The
fuel
tank
filler
is located
on
the
rear
driver side of your vehicle. The
fuel
tank
filler
door
can
be
opened
from
inside
the
vehicle
with
the
fuel
tank
filler
door
release
lever
located
at the
left
side of the driver
’s seat.
3.Open
the
fuel
tank
filler
pipe
by
slowly
turning the cap counterclockwise.4.While
filling
with
fuel,
store
the
cap
in the
cap
holder
located
on
the
inside
of the
fuel
tank filler door
.
5.To fill
with
fuel
correctly
depends
mainly
on
correct
handling
of
the
fuel
filler
noz-
zle.
Do
not
tilt
the
nozzle.
Insert
the
noz-
zle in the tank port as far as it will go.6.When
the
nozzle
stops
automatically
, do
not attempt to add more fuel.
Keep
the
doors
and
windows
clos
ed while
refuelin
g the
veh
icle.
If the
y were ope
n,
fuel vapor
could get
into the
cabin.
Fuel tank capacity Refueling
W
AR
NING
A-Remove
B-
Close W
AR
NING
Since
the
fuel
system
may
be
under
pres-
sur
e, remove
the
fuel
tank
filler
cap
slowly
. This
relieves
any
pressur
e or
vac-
uum
that
might
have
built
up
in the
fuel
tank.
If the
cap
is venting
vapor
or if you
hear
a hissing
sound,
wait
until
it stops
befor
e removin
g the
cap.
Otherw
ise, fue
l
may
spray
out,
injuring
you
or others.
CAUTIONYour
vehicle
can
onl
y be ope
rated
using
unlead
ed gasolin
e. Serious
engi
ne and
cata-
lytic
conve
rter damag
e will
result
if lead
ed
gasoline
is used.
CAUTIONTo avoi
d fuel
spillag
e and
ove
rfilling,
do
not
“top-of
f”
the
fuel
tank.
Spilled
fuel
could
discolor
, stain,
or crack
the
vehicle’
s paint-
work.
If fuel
spills
on
the
paintw
ork,
wipe
it
off with
a soft
cloth.

Modifications to and racing of your vehicle
General information
3-5
3
7.To close,
turn
the
fuel
tank
filler
cap
slowly
clockwise
until
you
hear
clicking
sounds,
then
gently
push
the
fuel
tank
filler door closed.
N00301600
048
This
vehicle
should
not
be
modified
with
non-Mitsubishi
Motors
genuine
parts.
Mit-
subishi
Motors
designs
and
manufactures
high
quality
vehicles
with
an
emphasis
on
safety
and
durabilit
y. Modifications
using
non-Mitsubishi
Motors
genuine
parts
may
affect
the
performance,
safety
and/or
durabil-
ity
of
your
vehicle,
and
may
violate
applica-
ble state and/or federal regulations. DAMAGE
OR
PERFORMANCE
PROB-
LEMS
RESUL
TING
FR
OM
MODIFICA-
TIONS
TO OR
RACING
OF
YOU
R
VEHICLE
ARE
NOT
COVERED
UNDER
W
ARRANTY
.
Examples
of
modifications
to
your
vehicle
that
can
cause
damage
or
performance
prob-
lems
include
the
following:
Failure
to use
Mitsubishi
Motors
genuine
partsFailure
to use
required
fuel
and
fluids
Failure to use proper size tires and wheelsModification
of
the
fuel,
intake,
exhaust,
emission,
suspension,
engine,
drive
train
or electrical wiring systems
Modification
of
any
onboard
com-
puter/control
module,
including
repro-
gramming,
or
replacing/adding
chips
to
any
onboard
computer/control
module
Review
the
Warranty
and
Maintenance
Man-
ual
for
further
details
regarding
warranty
cov-
erage.
N00301700
182
The
installation
of
accessories,
optional
parts,
etc.,
should
only
be
carried
out
within
the
limits
prescribed
by
law
in the
driving
area
and
in
accordance
with
the
guidelines
and
warnings
contained
within
the
documents
accompanying
this
vehicle.
Only
Mitsubis
hi
Motors
approved
acces
-
sories should be fitted to your vehicle.Improper
installation
of
electrical
parts
could
cause
fire.
Refer
to
the
“Modifica-
tion/alterations
to
the
electrical
or
fuel
systems”
section
with
in this
owner
’s man
-
ual.
W
AR
NING
Make
sur
e the
fuel
cap
is secur
ely closed.
If the
fuel
cap
is loose,
fuel
could
leak,
resulting
in a fire.
CAUTIONIf you
need
to replace
the fuel
tank
filler
cap
,
use only
the
cap
specified
for
your
model
vehicle. NOTE
If the
fuel
tank
filler
cap
is not
tight
while
driving,
the
engine
malfunction
indicator
(“SER
VICE
ENGINE
SOON”
or
“Check
engin
e light”)
may
come
on when
the
onboard
diagnostic
(OBD)
system
performs
a self check.
Always
tigh
ten
the
fuel
tan
k filler
cap
until
you
hear
clicking
sounds.
The indicator
will go off after drivin
g several
times.
If the
indicator
does not go off, con
-
tact
your authorized
Mitsubishi
Mot
ors
dealer
or a repair
facility
of your
choice
as
soon
as possible.
Modifications to and racing of your vehicle
Installation of accessories
CAUTIONBef
ore any electr
ical
or
electronic
accesso-
ries are installed,
consult
an
authorized
Mit-
subishi
Motors
dealer
.

Trunk lid
Features and controls 5-39
5
N00509501198
Insert the key and turn it clockwise. The trunk lid will pop up
slightly. Lift it to
open the trunk. Press the trunk button (Vehicles with keyless entry system or F.A.S.T.-key) or OPEN switch (Vehicles with F.A.S.T.-key). (See
“Keyless entry system” on page 5-7, 5-30 or “Free-hand Advanced Security Transmitter (F.A.S.T.-key)” on page 5-12.) The trunk lid will pop up
to slightly. Lift it to
open the trunk. Pull the trunk lid release lever, located to the left of the driver’s seat, up to open the trunk.
Trunk lid
WA R N I N G It is dangerous to drive with the trunk lid open since carbon monoxide (CO) gas can enter the cabin. CO is an invisible, odor- less gas that can cause unconsciousnessand even death. Do not allow children to have access to the trunk, either by climbing into the trunk from outside or through the inside of the vehicle. Always close the trunk lid whenyour vehicle is unattended. If trapped in the trunk, it is possible to escape from the trunk by using the in
side emergency trunk
release lever. (See “Inside emergency trunk lid release” on page 5-40.)CAUTION Do not stand behind the exhaust pipe when loading and unloading luggage. Heat from the exhaust could lead to burns.
To open Operation from outside the vehicle Using the key (Vehicles with key cylin- der) Using the remote control transmitter (Vehicles with keyless entry system orF. A . S . T. - k e y )
CAUTION Do not use the trunk lid release lever while the vehicle is moving. If the trunk lid is opened, objects in the trunk could fall ontothe road and cause an accident.
BK0230300US.bo
ok 39 ページ ２０１５年７月３０日　木曜日　午後８時３８分

Warning lights 5-124 Features and controls
5
N00520300147 N00520400467
When the ignition switch is turned to the “ON” position, this indicator normally comeson and goes out a few seconds later. A warn- ing is also displayed in the multi-information display.The warning light also illuminates after start-ing the engine under the following condi- tions:  When the parking brake is still applied.  When the brake fluid level is low.  When the brake force distribution func- tion is not operating correctly.
Before driving, be sure that the parking brake is fully released and brake warning light isoff.
N00520501830
This indicator is a part of the onboard diag- nostic (OBD) system which monitors the emissions, engine contro
l system or continu-
ously variable transmission (CVT) control system. If a problem is detected in one of these systems, this indicator illuminates orflashes. When the ignition switch is turned tothe “ON” position, this indicator normally comes on and goes off after the engine has started. This indicator will come on if the fuel tank filler cap is not properly tightened. If this indicator comes on and stays on after refuel- ing, stop the engine and check that the cap isproperly tightened. (Turn the cap clockwise until you hear clicking sounds.) If this indicator does not go off after severalseconds or lights up while driving, have the system checked as soon as possible at an authorized Mitsubishi Motors dealer or arepair facility of your choice.
Warning lights Brake warning light
CAUTION If the brake warning light and the anti-lock braking system warning light are illuminated at the same time, the braking force distribu-tion function will not operate, so the vehicle may be destabilized during sudden braking under the following conditions.
• When the brake warning light does not go out even when the parking brake is released.• When the brake warning light stays onwhile driving.• If the above occurs, avoid sudden brakingand high-speed driving. Park the vehicle in a safe place, and contact an authorized Mit- subishi Motors dealer or a repair facility ofyour choice as soon as possible.
 The vehicle should be brought to a halt in the following manner when brake performance is deteriorated.• Confirm that the vehicle slows down whenyou press down on the brake pedal harder than usual. In some cases, the brake pedalmay go all the way to the floor.• Should the brakes fail, use engine brakingto reduce your speed and slowly apply the parking brake. Depress the brake pedal to illuminate thestop lights to alert the vehicles behind you.
 Do not suddenly apply the parking brake while driving. This may cause the rear wheels to lock and cause an accident.CAUTION
Engine malfunction indicator (“SERVICE ENGINE SOON” or “Check engine light”)
BK0230300US.book
124 ページ ２０１５年７月３０日　木曜日　午後８時３８分

7
Comfort controlsVents .........................................
.......................................................7-2
Heater without air conditioning function (if so equipped) ...............7-4 Automatic air conditioning
with Fahrenheit scale
(if so equipped) .
.................................................
..........................7-7
Automatic air conditioning with Cels
ius scale (if so equipped) .....7-12
Important air conditioning op
erating tips ......................................7-18
Air purifier ......................
...............................................................7-18
AM/FM radio/CD player (if so equipped) .....................................7-19 Handling of Discs .
.................................................
........................7-22
Audio Files (MP3/WMA/
AAC) ....................................................7-24
Important Points on Safety fo
r the Customer ................................7-28
Operation Keys ...............
...............................................................7-28
Listen to Radio ......
.................................................
........................7-32
Listen to Satellite Radio (if so equipped) .......................................7-33 Listen to CDs ..................
...............................................................7-35
Listen to MP3s ......
.................................................
........................7-36
Listen to an iPod ...
.................................................
........................7-37
Listen to Audio Files on
a USB Device .........................................7-39
To play iPod/USB memory device tracks via voice operation (vehicles with Bluetooth 2.0
interface) ......................................7-42
Listen to Bluetooth Audio (i
f so equipped) ....................................7-45
Display Indicator ..
.................................................
........................7-47
Audio Quality and Volume Balance Adjustment ...........................7-48System Settings .....
.................................................
........................7-49
Troubleshooting ..............
...............................................................7-53
Antenna .....................................
.....................................................7-55
Clock (if so equipped)
............................................
........................7-56
General information about
your radio ...........................................7-57
BK0230300US.bo
ok 1 ページ ２０１５年７月３０日　木曜日　午後８時３８分

Heater without air conditioni
ng function (if so equipped)
7-4 Comfort controls
7
Air flows mainly to the windshield and the door windows.
N00737700031
The heater can only be used while the engineis running.
N00737800029
N00737900020
When the ignition switch is in the “ON” posi- tion, select the blower speed by turning theblower speed selection dial. Turning the dial clockwise will increase the blower speed; turning the dial counterclock-wise will decrease it. When the dial is set to the “OFF” position, all fan-driven airflow will stop.
NOTE
 With the mode selection dial between the “ ” and “ ” positions, air flows mainly to the leg area. With the mode selection dial between the “ ” and “ ” positions, air flows mainly to the windshield and the door windows.
Defroster position
Heater without air condi- tioning function
(if so equipped)
Control panel

1- Temperature control dial 2- Air selection switch 3- Blower speed selection dial 4- Mode selection dial5- Electric rear window defogger switch
 P. 5-138
NOTE
Button (A) is not available for use. The indi- cator below the button doesn’t come on even if it is pushed.
Blower speed selection dial

BK0230300US.bo
ok 4 ページ ２０１５年７月３０日　木曜日　午後８時３８分

Heater without air conditioni
ng function (if so equipped) Comfort controls 7-5
7
N00738000044
Turn the temperature control dial clockwise to make the air warmer. Turn it counterclock-wise to make the air cooler.
N00738100058
To change the amount of air flowing from thevents, turn the mode selection dial. Refer to“Changing the mode selection” on page 7-2.
N00738200033
Normally, use the outside air position to keepthe windshield and side windows clear and toquickly remove fog or frost from the wind- shield. To change the air selection, simply press the air selection switch. A sound will be made every time you push the switch.  Outside air {Indicator light (A) OFF}  Recirculation air {Indicator light (A) ON}
The air selection indicator light (A) shows the selected position. If the outside air is dusty or contaminated in some way, use the recirculation position.Switch to the outside air position every now and then to keep th
e windows from fogging
up.
Temperature control dial

NOTE
 While the engine coolant temperature is low, the temperature of the air from the heater will be cool/cold until the engine warms up, even if you have selected warm air with thedial.
Mode selection dial

Air selection switch

CAUTION Using recirculated air for a long time may cause the windows to fog up.
BK0230300US.bo
ok 5 ページ ２０１５年７月３０日　木曜日　午後８時３８分

Heater without air conditioni
ng function (if so equipped)
7-6 Comfort controls
7
N00738300034
Set the mode selection dial to the “ ” posi- tion and set the air selection switch (A) to the outside air position.Turn the temperature control dial clockwiseor counterclockwise to the desired tempera- ture. Select the best speed to fit your needs.
N00738400022
Set the mode selection dial to the positionsshown in the illustration and set the air selec- tion switch (A) to the outside air position. The air flow will be di
rected to the leg area
and the upper part of the passenger compart- ment. Set the desired blower speed. Warm air flows to the leg area and unheatedor slightly warm air (depending upon theposition of the temperat
ure control dial) flows
to the upper part of the passenger compart- ment.
Operating the system

Heating

NOTE
 For quick heating, set the blower speed selection dial to the position shown in the illustration.
Combination of unheated air and heated air

BK0230300US.bo
ok 6 ページ ２０１５年７月３０日　木曜日　午後８時３８分

Automatic air conditioning with
Fahrenheit scale (if so equipped)
7-8 Comfort controls
7
N00736900094
When the ignition switch is in the “ON” posi- tion, select the blower speed by turning the blower speed selection dial. Turning the dial clockwise will increase theblower speed; turning the dial counterclock- wise will decrease it. When the dial is set to the “OFF” position, all fan-driven airflowwill stop.
N00737001376
Use this dial to adjust the temperature in thepassenger compartment. Turn the temperaturecontrol dial clockwise to make the air warmer. Turn it counterclockwise to make the air cooler.
The above indicates the factory settings. You can personalize the air selection switch and air conditioning switch to match your per-sonal preferences. Contact your Mitsubishi Motors dealer or a repair facility of your choice for assistance.Refer to “Personalizing the air conditioning switch (Changing the function setting)” on page 7-10.Refer to “Personalizing the air selection (Changing the function setting)” on page 7-9.
NOTE
 There is an interior air temperature sensor (A) in the illustrated position. Never place anything over the sensor, since doing so will prevent it from functioning properly.
Blower speed selection dial

Temperature control dial

NOTE
 While the engine coolant temperature is low, the temperature of the air from the heater will be cool/cold until the engine warms up, even if you have selected warm air with the dial.  When the temperature is set to the highest or the lowest setting under the AUTO opera-tion, the air selection and the air conditioning will be automatically changed as follows. • Quick Heating (When the temperature is set to the highest setting) Outside air will be introduced and the airconditioning will stop. In this case, manual operation is possible. • Quick Cooling (When the temperature is set to the lowest setting) Inside air will be recirculated and the airconditioning will operate. In this case, you cannot select outside air and turn the air conditioning off.
BK0230300US.bo
ok 8 ページ ２０１５年７月３０日　木曜日　午後８時３８分

Automatic air conditioning with
Celsius scale (if so equipped)
Comfort controls 7-13
7
N00711801594
N00736900111
When the ignition switch is in the “ON” posi- tion, select the blower speed by turning the blower speed selection dial. Turning the dial clockwise will increase theblower speed; turning the dial counterclock- wise will decrease it. When the dial is set to the “OFF” position, all fan-driven airflowwill stop.
N00737001389
Use this dial to adjust the temperature in thepassenger compartment. Turn the temperaturecontrol dial clockwise to make the air warmer. Turn it counterclockwise to make the air cooler.
Control panel

1- Temperature control dial 2- Air selection switch 3- Blower speed selection dial4- Air conditioning switch 5- Mode selection dial 6- Electric rear window defogger switch
 P. 5-138
NOTE
There is an interior
air temperature sensor
(A) in the illustrated position. Never place anything over the sensor, since doing so will prevent it from functioning properly.
Blower speed selection dial

Temperature control dial

BK0230300US.bo
ok 13 ページ ２０１５年７月３０日　木曜日　午後８時３８分