clock MITSUBISHI LANCER EVOLUTION VI 1999 User Guide

REAR AXLE – On-vehicle Service <Vehicles with AYC>REAR AXLE – On-vehicle Service <Vehicles with AYC>27-34
BLEEDING
1. Lift up the vehicle.
2. Connect the MUT-II to the 16-pin diagnosis connector.
Caution
Before connecting or disconnecting the MUT-II,
always turn off the ignition switch.
3. Turn on the ignition switch.
4. Operate the MUT-II (Item No.10) to activate the hydraulic
unit forcibly.
NOTE
(1) The forced activation (air bleeding mode) will be
automatically canceled after 5 minutes operation. It
can also be canceled forcibly by operating the clear
key on the MUT-II.
(2) While this function is being disabled by the fail-safe
function, the forced activation of the hydraulic unit
can not be executed.
5. Remove the cap of the left bleeder screw on the torque
transfer differential and connect a vinyl hose.
6. Gradually turn the steering wheel clockwise from the
straight-ahead position. At this time, loosen the left bleeder
screw and check that fluid is discharged with air.
7. After air has been completely discharged, tighten the
bleeder screw.
Caution
While the system is being bled of air, add fluid as
necessary to ensure that it is left in the oil reservoir
during the entire procedure.
8. Repeat steps (6) and (7) two to three times until no air
bubbles are recognized in the fluid that comes out. Then,
tighten the bleeder screw to the specified torque.
Tightening torque: 9 Nm
9. Perform steps (5) through (8) for the right bleeder screw.
Note, however, that the steering wheel should be turned
counterclockwise.
10. After the system has been completely bled of air, check
for the fluid level. (Refer to P.27-33.)
Caution
If the system is not completely bled of air, the hydraulic
unit could generate noise, degrading pump durability.
AYC OPERATION CHECK
1. Lift up the vehicle.
2. Connect the MUT-II to the 16-pin diagnosis connector.
Caution
Before connecting or disconnecting the MUT-II, always
turn off the ignition switch.
3. Start the engine.
4. Operate the MUT-II with the transmission in 2nd or a
higher gear and check to ensure that the vehicle speed
is higher than 10 km/h using the Data List (Item 10).
Bleeder
screws Vinyl hose

REAR AXLE – Sensor Relay <Vehicles with AYC>27-41
SENSOR RELAY <VEHICLES WITH AYC>
REMOVAL AND INSTALLATION
Caution: SRS
For vehicles with SRS, before removal of air bag module and clock spring, refer to GROUP 52B
– Service Precautions and Air Bag Module and Clock Spring.
12
3
4
Steer sensor removal steps

Steering wheel and column cover
A1. Steer sensorAcceleration sensor and AYC relay
removal
2. Longitudinal acceleration sensor
3. Lateral acceleration sensor
4. AYC relay
NOTE
For the wheel speed sensor, refer to GROUP 35B.
REMOVAL SERVICE POINT
ASTEER SENSOR REMOVAL
Remove the steer sensor from the column switch.
Caution
(1) A photocoupler is used as the steer sensor. Use care
not to allow dust or grease to be on the sensor.
(2) Do not bend or dirty with grease the slit plate on
the column switch side.Slit plate
Steer sensor

37A-1
STEERING
CONTENTS
GENERAL 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Outline of Change 2. . . . . . . . . . . . . . . . . . . . . . . . .
STEERING WHEEL AND SHAFT* 2. . . . . . . .
POWER STEERING GEAR BOX* 5. . . . . . . . .
WARNINGS REGARDING SERVICING OF SUPPLEMENTAL RESTRAINT SYSTEM (SRS) EQUIPPED VEHICLES
WARNING!
(1) Improper service or maintenance of any component of the SRS, or any SRS-related component, can lead to personal
injury or death to service personnel (from inadvertent firing of the air bag) or to the driver and passenger (from rendering
the SRS inoperative).
(2) Service or maintenance of any SRS component or SRS-related component must be performed only at an authorized
MITSUBISHI dealer.
(3) MITSUBISHI dealer personnel must thoroughly review this manual, and especially its GROUP 52B – Supplemental
Restraint System (SRS) before beginning any service or maintenance of any component of the SRS or any SRS-related
component.
NOTE
The SRS includes the following components: SRS-ECU, SRS warning lamp, air bag module, clock spring and interconnecting
wiring. Other SRS-related components (that may have to be removed/installed in connection with SRS service or maintenance) are
indicated in the table of contents by an asterisk (*).

STEERING – General / Steering Wheel and Shaft37A-2
GENERAL
OUTLINE OF CHANGE

The service procedures for left-hand drive vehicles have been established as described below. The
service procedures for components not mentioned below are the same as for the preceding models.
STEERING WHEEL AND SHAFT <L.H. DRIVE VEHICLES>
REMOVAL AND INSTALLATION
CAUTION: SRS
For vehicles with SRS, before removal of air bag module, refer to GROUP 52B – Service Precautions and
Air Bag Module and Clock Spring.
Pre-removal Operation
Instrument Under Cover RemovalPost-installation Operation

Instrument Under Cover Installation

Checking Steering Wheel Position with Wheels
Straight Ahead
<Vehicles without SRS>
5 Nm
17 Nm11 Nm
<Vehicles with SRS>
10
98 431
532
41 Nm
25 Nm
6
25 Nm41 Nm
7
9 Nm
Section A – A Section B – B
Claw
: Claw position
AB 4
5
AB
11 Nm 21 Nm Standard bolt Earth bolt
NOTE
4
5
Claw
Removal steps
1. Horn pad <Vehicles without SRS>
2. Air bag module
(Refer to GROUP 52B – Air Bag
Module and Clock Spring.)
A3. Steering wheel
4. Upper column cover
5. Lower column coverA6. Column switch
<Vehicles without SRS>
A7. Clock spring and column switch
(Refer to GROUP 52B – Air Bag
Module and Clock Spring.)
8. Steering shaft assembly
9. Band
10. Steering cover assembly

STEERING – Steering Wheel and Shaft37A-3
REMOVAL SERVICE POINT
ASTEERING WHEEL REMOVAL
INSTALLATION SERVICE POINT
ACLOCK SPRING AND COLUMN SWITCH / COLUMN
SWITCH INSTALLATION
Tighten the screws in an alphabetical order.
DISASSEMBLY AND REASSEMBLY
1
2
3 4
Disassembly steps
AA1. Special bolt
A2. Steering lock bracket
A3. Steering lock cylinder
4. Steering shaft
MB990803
A
BC

STEERING – Power Steering Gear Box37A-5
POWER STEERING GEAR BOX <L.H. DRIVE VEHICLES>
REMOVAL AND INSTALLATION
CAUTION: SRS
For vehicles with SRS, before removal of steering gear box, refer to GROUP 52B, centre front wheels and
remove ignition key. Failure to do so may damage SRS clock spring and render SRS system inoperative,
risking serious driver injury.
Pre-removal Operation

Power Steering Fluid Draining

Center Member Removal

Front Exhaust Pipe RemovalPost-installation Operation

Front Exhaust Pipe Installation

Center Member Installation

Power Steering Fluid Supplying

Power Steering Fluid Line Bleeding

Steering Wheel Position Check with Wheels Straight
Ahead

Front Wheel Alignment Adjustment

Dust Cover Check for Cracks or Damage by
Pushing it with Finger.
15 Nm 15–33 Nm
69 Nm17 Nm
5 Nm
15–33 Nm
789
3
45 1 2
611 Nm
Removal steps
1. Steering shaft assembly and gear
box connecting bolt
2. Band
3. Split pin
A4. Tie-rod end and knuckle connection5. Return tube connection
6. Pressure tube connection
7. Cylinder clamp
B8. Gear box assembly
9. Steering cover assembly

STEERING – Power Steering Gear Box37A-10
DISASSEMBLY SERVICE POINTS
ARACK SUPPORT COVER REMOVAL
Use the special tool to remove the rack support cover from
the gear box.
BOIL SEAL / PINION AND VALVE ASSEMBLY
REMOVAL
Using a plastic hammer, gently tap the pinion to remove it.
CSEAL RING REMOVAL
Cut the seal ring and remove it from the pinion and valve
assembly and the rack.
Caution
When cutting the seal ring, be careful not to damage
the pinion and valve assembly or the rack.
DBALL BEARING / OIL SEAL REMOVAL
Use a socket, remove the oil seal and the ball bearing from
the valve housing assembly simultaneously.
ECIRCLIP REMOVAL
1. Turn the rack stopper clockwise until the end of the circlip
comes out of the slot in the rack housing.
2. Turn the rack stopper anticlockwise to remove the circlip.
Caution
Note that if the rack stopper is first turned
anticlockwise, the circlip will get caught in the slot
in the housing and the rack stopper will not turn.
MB990607
Socket
Rack stopper
Rack
Circlip

STEERING – Power Steering Gear Box37A-13
2. Cover rack serrations with special tool.
3. Apply the specified fluid on the special tool.
Specified fluid:
Automatic transmission fluid
DEXRON or DEXRON II
4. Match the oil seal centre with rack to prevent retainer
spring from slipping and slowly insert rack from power
cylinder side.
EOIL SEAL / RACK BUSHING INSTALLATION
1. Apply the specified fluid to the outer surface of the oil
seal. Press-fit the oil seal using the special tool until it
is flush with the bushing end face.
Specified fluid:
Automatic transmission fluid
DEXRON or DEXRON II
2. Apply the specified fluid to the oil seal inner surface and
the O-ring.
Specified fluid:
Automatic transmission fluid
DEXRON or DEXRON II
3. Wrap the rack end with plastic tape, and push the rack
bushing onto the rack.
FCIRCLIP INSTALLATION
Insert the circlip to the rack stopper hole through the cylinder
hole. Turn the rack stopper clockwise and insert the circlip
firmly.
Caution
Insert the circlip to the rack stopper hole while turning
the rack stopper clockwise.
GOIL SEAL / BALL BEARING INSTALLATION
1. Apply a coating of the specified fluid to the outside of
the oil seal. Using the special tools, press the oil seal
into the valve housing.
Specified fluid:
Automatic transmission fluid
DEXRON or DEXRON II
MB991214
Oil seal
Oil seal
MB990927
Rack
bushingO-ring
Rack bushingPlastic tape
Circlip
SlotCirclip
Slot
Oil sealMB990938
MB991203

STEERING – Power Steering Gear Box37A-14
2. Apply a coating of the specified fluid to the outside of
the ball bearing. Using the special tools, press the ball
bearing into the valve housing.
Specified fluid:
Automatic transmission fluid
DEXRON or DEXRON II
HSEAL RING INSTALLATION
1. Kneed the seal ring to soften it.
2. Apply the specified fluid to the seal ring, and install to
the rack groove.
Specified fluid:
Automatic transmission fluid
DEXRON or DEXRON II
3. Insert the tapered side of the special tool from the pinion
gear side, and compress the seal ring.
IOIL SEAL INSTALLATION
Use the special tool to press the oil seal into the valve housing.
The upper surface of the oil seal should project outwards
approx. 1 mm from the housing edge surface.
Caution
If the oil seal is flush with or lower than the housing
edge, it will cause oil leaks and require reassembly.
JEND PLUG INSTALLATION
1. Apply the specified sealant to the threaded part of the
end plug.
Specified sealant:
3M ATD Part No.8661 or equivalent
2. Secure the threaded portion of the end plug at two places
by using a punch.
KTOTAL PINION TORQUE ADJUSTMENT
1. Position the rack at its centre. Tighten the rack support
cover to 15 Nm.
2. In neutral position, rotate the pinion shaft clockwise one
turn/4 – 6 seconds with the special tool. Return the rack
support cover 30 – 60 and adjust torque to the standard
value.
Ball bearingMB990938
MB991203
Pinion gearMB991317
Tapered side
Approx. 1 mmMB990941
End plug
SealantEnd plug
MB991006

52B-1
SUPPLEMENTAL
RESTRAINT
SYSTEM (SRS)
CONTENTS
GENERAL INFORMATION 2. . . . . . . . . . . . . . . .
SRS SERVICE PRECAUTIONS 3. . . . . . . . . . .
SPECIAL TOOLS 5. . . . . . . . . . . . . . . . . . . . . . . .
TEST EQUIPMENT 5. . . . . . . . . . . . . . . . . . . . . .
TROUBLESHOOTING 6. . . . . . . . . . . . . . . . . . . .
SRS MAINTENANCE 15. . . . . . . . . . . . . . . . . . .
POST-COLLISION DIAGNOSIS 19. . . . . . . . .
INDIVIDUAL COMPONENT SERVICE 22. . . WARNING/CAUTION LABELS 23. . . . . . . . . .
SRS AIR BAG CONTROL UNIT
(SRS-ECU) 24. . . . . . . . . . . . . . . . . . . . . . . . . . . .
AIR BAG MODULES AND CLOCK
SPRING 25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AIR BAG MODULE DISPOSAL
PROCEDURES 32. . . . . . . . . . . . . . . . . . . . . . . .
Undeployed Air Bag Module Disposal
Procedures 32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Deployed Air Bag Module Disposal
Procedures 40. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CAUTION

Carefully read and observe the information in the SERVICE PRECAUTIONS (P.52B-3.) prior to any service.

For information concerning troubleshooting or maintenance, always observe the procedures in the Troubleshooting
(P.52B-6.) section.

If any SRS components are removed or replaced in connection with any service procedures, be sure to follow the
procedures in the INDIVIDUAL COMPONENT SERVICE section (P.52B-22.) for the components involved.

If you have any questions about the SRS, please contact your local distributor.