steering MITSUBISHI LANCER EVOLUTION VI 1999 User Guide

MPI – Troubleshooting13-64
Terminal
No.Normal condition Check condition (Engine condition) Check item
20Radiator fan motor
relay (HI)
<EVOLUTION VI>
Radiator fan not operating (coolant temperature:
95C or below)System voltage
<EVOLUTION-VI>Radiator fan at high speed (coolant temperature:
105C or above)0 – 3 V
21Fan motor relay (LOW)
<EVOLUTION-IV, V>Fan not operating (coolant temperature: 95C or
below)System voltage
Fan at low speed (coolant temperature: 95 – 100C)0 – 3 V
21Radiator fan motor
relay (LOW)
<EVOLUTION VI>
Radiator fan not operating (coolant temperature:
95C or below)System voltage
<EVOLUTION-VI>Radiator fan at low speed (coolant temperature: 95
– 105C)0 – 3 V
22A/C relay
Engine: Idling

A/C switch: OFF to ON (Compressor is being
driven.)System voltage, or 6
V or more instanta-
neously to 0 – 3 V
32A/C condenser fan
motor relay (HI)
<EVOLUTION VI>
A/C condenser fan not operating (A/C switch: ON,
coolant temperature: 105C or below)System voltage
<EVOLUTION-VI>A/C condenser fan at high speed (A/C switch: ON,
coolant temperature: 105C or above)0 – 3 V
33Alternator G terminal
Engine: Warm, idle (radiator fan: OFF)

Headlamp: OFF to ON

Brake lamp: OFF to ON

Rear defogger switch: OFF to ONVoltage rises by 0.2 –
3.5 V.
34A/C condenser fan
motor relay (LOW)
<EVOLUTION VI>
A/C condenser fan not operating (A/C switch: OFF,
coolant temperature: 105C or below)System voltage
<EVOLUTION-VI>A/C condenser fan at low speed (A/C switch: OFF,
coolant temperature: 105C or above)0 – 3 V
36Engine warning lampIgnition switch: OFF → ON0 – 3 V → System
voltage (After several
seconds have
elapsed)
37Power steering fluid
pressure switchEngine: Idling after
warming upWhen steering wheel is
stationarySystem voltage
When steering wheel is
turned0 – 3 V
38Control relayIgnition switch: OFFSystem voltage
Ignition switch: ON0 – 3 V
39Fuel pump relay No.2While engine is idling, suddenly depress the
accelerator pedal.Momentarily rises
slightly from 0 to 3 V.
40Exhaust temperature
warning lampIgnition switch: OFF to ON0 – 3 V to system
voltage (After several
seconds have
elapsed)

REAR AXLE – Special Tools / Troubleshooting <AYC>27-4
MB990925
Brass bar
Bar (one-touch type)Toolbox
Installer adapter
Tool number (MB990925)O.D. mmTool number (MB990925)O.D. mm
AMB99092639.0AMB99093363.5
MB99092745.0MB99093467.5
MB99092849.5MB99093571.5
MB99092951.0MB99093675.5
MB99093054.0MB99093779.0
MB99093157.0BMB990938–
MB99093261.0CMB990939–
TROUBLESHOOTING <AYC>
BASIC TROUBLESHOOTING CONDITIONS
Refer to Group 00 – How to Use Troubleshooting / Inspection Service Points.
NOTE
Before starting the troubleshooting procedure, make sure that the following items have been checked
okay.

The correct steering wheel has been properly installed in the neutral position of the steering column
shaft.

Tire and wheel sizes are correct with correct specifications. Inflation pressure, balance, and wear
conditions are okay.

Wheel alignment is correct.

The engine, suspension, and other parts have not been remodeled so as to affect the AYC system.
DIAGNOSIS FUNCTION
READING THE DIAGNOSIS CODE
Read the diagnosis code using an MUT-II tester or the AYC warning lamp.
(Refer to Group 00 – How to Use Troubleshooting / Inspection Service Points.)
ERASING THE DIAGNOSIS CODE
Refer to Group 00 – How to Use Troubleshooting / Inspection Service Points.

REAR AXLE – Troubleshooting <AYC>27-8
Code No. 25: Wrong-diameter tireProbable cause
This code is output if the speed of any one of the four wheels exceeds a specified
level with respect to the average of the four wheel speed sensor outputs when the
steering wheel is in the straight-ahead position and the vehicle speed exceeds 20
km/h. At this time, the warning lamp does not light up.
Defective harness or connector

Defective AYC-ECU

Defective ABS-ECU
<Vehicles with ABS>
OK
Replace ABS-ECU.
NG
Check harness between AYC-ECU
and ABS-ECU.NG
Repair
NG
Replace AYC-ECU.
OK
Check the trouble symptom.
NG
Check the following connectors:
B-24, B-95NG
Repair
OK
Check the trouble symptom.
NO
Measure at B-95 AYC-ECU connector.

Disconnect the connector and
measure at the harness side.

Ignition switch: ON

Turn tire at 1/2 to 1 revolution/sec.

Voltage across 6/7/8/9 and body
ground.
OK:42 mV or more (when mea-
sured with a circuit tester)
120 mV-P or more (when
measured with an oscillo-
scope)OKCheck the following connector:
B-95
YES
Is ABS diagnosis code No. 15 output?YESGroup 35* – Refer to Troubleshooting
Are correct tires mounted on all four
wheels?NO
Repair
NG
Repair
<Vehicles without ABS>
NO
Repair
NOCheck and repair the harness between
wheel speed sensor and AYC-ECU.
OK
Check the trouble symptom.
OK
Check the following connectors:
B-95, B-52, B-17, A-26, A-50, D-04,
D-14, D-19NG
Repair
OK
Check wheel bearing.NG
Replace
NG
Replace AYC-ECU.
OK
Check the trouble symptom.
OK
Check the following connector:
B-95NG
Repair
OK
Check wheel speed sensor output volt-
age. (Refer to p. 27-37.)NGCheck wheel speed sensor and ABS
rotor. (Refer to Group 35B.)
YES
Check Wheel speed sensor for instal-
lation.NG
Repair
Are correct tires mounted on all four
wheels?
NG
Replace

REAR AXLE – Troubleshooting <AYC>27-10
Code No. 31: Steer sensor (ST-1, ST-2, ST-N) systemProbable cause
This code is output when any of the steer sensors ST-1, ST-2, and ST-N is open-circuited
or the steer sensor ground wire is open-circuited.
Defective steer sensor

Defective harness or connector

Defective AYC-ECU
OK
Replace the steer sensor.
NG
Check the harness between steer sen-
sor and AYC-ECU.NG
Repair
NG
Check and repair the harness between
speed sensor and AYC-ECU.
OK
Check the trouble symptom.
OK
Check the trouble symptom.
OK
Check the following connectors:
B-95, B-65, B-98NG
Repair
NG: Voltage remains
at 4 V or more.
Measure at B-98 steer sensor connec-
tor.

Disconnect the connector and
measure at the harness side.

Continuity across 3 and body
ground
OK:ConductingNGCheck the following connectors:
B-98, B-50NG
Repair
NG
Replace AYC-ECU.
OK
Check the trouble symptom.
Measure at B-95 AYC-ECU connector.

Connector connected.

Ignition switch: ON

Voltage across 4/5/17 and body ground.
OK:The voltage alternates between about
3 V and about 0.5 V when the steering
wheel is turned.OKCheck the following connector:
B-95NG
Repair
NG: Voltage alternates
between 4 V or
more and 0.5 V.NG: Voltage
remains
at 0 V.
Code No. 32: Steer sensor (ST-N) systemProbable cause
This code is output when the steering wheel is considered to be turned 40 or more
as determined with ST-1 and ST-2 with ST-N ON (LOW voltage).
Defective steer sensor

Defective harness or connector

Defective AYC-ECU
OK
Replace the steer sensor.
NG
Check the harness between steer sen-
sor and AYC-ECU.NG
Repair
OK
Replace AYC-ECU.
NG
Replace AYC-ECU.
OK
Check the trouble symptom.
OK
Check the trouble symptom.
NG
Measure at B-95 AYC-ECU connector.

Disconnect the connector and
measure at the harness side.

Ignition switch: ON

Turn steering wheel about 90 in
either direction from the straight-
ahead position.

Voltage across 17 and body
ground.
OK:No continuityNGCheck the following connectors:
B-95, B-65, B-98NG
Repair
Measure at B-95 AYC-ECU connector.

Connector connected.

Ignition switch: ON

Turn steering wheel about 90 in
either direction from the straight-
ahead position.

Voltage across 17 and body
ground.
OK:The voltage increases from
about 0.5 V or less to about
3 V.OKCheck the following connector:
B-95NG
Repair

REAR AXLE – Troubleshooting <AYC>27-11
Code No. 33: Steer sensor (ST-N) systemProbable cause
This code is output when the steering wheel is turned 400 or more in the same
direction with ST-N OFF (HIGH voltage).
Defective steer sensor

Defective harness or connector

Defective AYC-ECU
NG
Replace AYC-ECU.
Check the trouble symptom.
OK
Replace the steer sensor.
NG
Check the harness between steer sen-
sor and AYC-ECU.NG
Repair
OK
Replace AYC-ECU.
OK
Check the trouble symptom.
Measure at B-95 AYC-ECU connector.

Connector connected.

Ignition switch: ON

Turn steering wheel about 90 in
either direction from the straight-
ahead position.

Voltage across 17 and body
ground.
OK:The voltage increases from
about 0.5 V or less to about
3 V.NGCheck the following connectors:
B-95, B-65, B-98NG
Repair
Code No. 34: Steer sensor (ST-1, ST-2) systemProbable cause
This code is output if a turning condition is detected for a cumulative period of time
of 15 min. or more, during which there is no change in the steer sensor (ST-1, ST-2)
signals with the wheel speed 15 km/h or more.
Defective steer sensor

Defective harness or connector

Defective AYC-ECU
NG
Replace AYC-ECU.
Check the trouble symptom.
OK
Replace the steer sensor.
NG
Check the harness between steer sen-
sor and AYC-ECU.NG
Repair
OK
Replace AYC-ECU.
OK
Check the trouble symptom.
Measure at B-95 AYC-ECU connector.

Connector connected.

Ignition switch: ON

Voltage across 4/5 and body
ground
OK:The voltage alternates
between about 0.5 V and
about 3 V as the steering
wheel is turned.NGCheck the following connectors:
B-95, B-65, B-98NG
Repair

REAR AXLE – Troubleshooting <AYC>27-25
DATA LIST REFERENCE TABLE
The following items can be read by t01he MUT-

from the ECU input data.
Item No.
Check itemChecking requirementsNormal value
01Front-right wheel speedPerform a test run.Vehicle speeds
displayed on the
02Front-left wheel speed
displayed on the
speedometer and
MUTIIare identi03Rear-right wheel speedMUT-II are identi-
cal.
04Rear-left wheel speed
05Front-right wheel speed
(0.2 km/h)
06Front-left wheel speed (0.2
km/h)
07Rear-right wheel speed
(0.2 km/h)
08Rear-left wheel speed (0.2
km/h)
10Vehicle speed
11System voltageIgnition switch: ONBattery voltage
15TPS openingAccelerator pedal position/Igni-
tion switch: ON
Fully closed300 – 1000mV
tion switch: ON
Partially openGradually increases
from the above val-
ue.
Fully open4500 – 5000mV
19Longitudinal acceleration
sensor
Vehicle stands on level ground2.4 – 2.6V
sensor
Perform a test run.Reading fluctuates
up or down with 2.5V
as its center.
20Lateral acceleration sensorVehicle stands on level ground2.4 – 2.6V
Perform a test run.Reading fluctuates
up or down with 2.5V
as its center.
22Steering wheel operationSteering wheel turning direction
Ignition switch: ON90 deg. clock-
wiseR90 deg
90 deg counter-
clockwiseL90 deg
23Steering wheel turning
angular velocity
Steering wheel position
Ignition switch: ON
Not turned0 deg/s
angular velocityIgnition switch: ON
TurnedReading varies ac-
cording to turning
speeds.
45Idle position switchAccelerator pedal position
Ignition position: ON
Not depressedON
Ignition position: ON
DepressedOFF

REAR AXLE – Troubleshooting <AYC>27-26
Item No.Normal value Checking requirements Check item
46Steer sensor (ST-N)Steering wheel position
Ignition switch: ON
Neutral positionON
Ignition switch: ON
90 deg. turned
from neutral
positionOFF
47Steer sensor (ST-1)Steering wheel position: Turn slowly counterclock-
wise.
Ignition switch: ONON and OFF are
indicated alternate-
ly.
48Steer sensor (ST-2)Steering wheel position: Turn slowly clockwise.
Ignition switch: ONON and OFF are
indicated alternate-
ly.
50Stop lamp switchAccelerator pedal position
Ignition switch: ON
DepressedON
Ignition switch: ON
ReleasedOFF
56Pressure switchForced activation No.13 or
No.14 is being executed.Electric pump in
operationLow
Electric pump
not in operationHigh
59ABS monitorABS monitorON
ABS not in operationOFF

REAR AXLE – Troubleshooting <AYC>27-27
ACTUATOR TEST REFERENCE TABLE
The following items can be tested by driving the corresponding actuator forcibly using the MUT-II.
Item No.Check itemChecking requirementsNormal value
10Air bleedingSupply current to proportioning
valve in accordance with steering
angle to operate directional valve.No air is to be bled from the
bleeder plug on the torque transfer
differential.
11Oil level checkLet the directional valve operate to
left and right 20 times.To be checked by oil level in
reservoir tank.
12Electric pump operationLet the electric pump operate for 5
seconds.Operation sounds of the electric
pump are to be heard.
13Clutch operation (left)Let the directional valve operate to
supply the maximum pressure to the
left clutch.The operation conditions are to be
checked by the speed difference
between left and right rear wheels
with the wheels raised. For details,
refer to AYC Operation Check on
P.27-34.
14Clutch operation (right)Let the directional valve operate to
supply the maximum pressure to the
right clutch.The operation conditions are to be
checked by the speed difference
between left and right rear wheels
with the wheels raised. For details,
refer to AYC Operation Check on
P.27-34.
15Control OFFTurn off the electric pump relay to
deactivate AYC control.During the test run, some
differences are to be recognized in
running behaviors between when
the system is ON and when it is
OFF.
NOTE
(1) The actuator test is feasible only when the following requirements are all satisfied.

All of inputs from four wheel speed sensors show 20 km/h or lower.

No system failure is registered.

The steering angle is within ±30 deg. from the neutral position.
(2) The actuator test comes to an end when either of the following conditions is met since the forced
actuation is canceled.

Either of inputs from four wheel sensors shows higher than 20 km/h (with exception of Item
No.15 “Control OFF”).

Some trouble with the system is registered.

Forced activation time expires.

MUT-II is removed.

The clear key of MUT-II is operated.

REAR AXLE – Troubleshooting <AYC>27-28
CHECK AT AYC-ECU TERMINALS
TERMINAL VOLTAGE LISTING

The voltage is to be measured across each terminal and ground terminal.

Fig. below shows the arrangement of the terminals.
Terminal
No.Check itemCheck requirementNormally
1Lateral acceleration sensorIgnition switch: ON2.4 – 2.6 V
(horizontal position)
2Longitudinal acceleration
sensor ground
Lateral acceleration sensor
groundAt all times0 V
3Longitudinal acceleration
sensorIgnition switch: ON2.4 – 2.6 V
(horizontal position)
4Steer sensor (ST-2)Engine: Idle speed
Turn steering wheel slowly.0 V ↔ approx. 3 V
flashing
5Steer sensor (ST-1)Engine: Idle speed
Turn steering wheel slowly.0 V ↔ approx. 3 V
flashing
6*1FR wheel speedVehicle stationary1 V or less
Forward vehicle slowly.0 – 5 V
7*1FL wheel speedVehicle stationary1 V or less
Forward vehicle slowly.0 – 5 V
8*1RR wheel speedVehicle stationary1 V or less
Forward vehicle slowly.0 – 5 V
9*1FL wheel speedVehicle stationary1 V or less
Forward vehicle slowly.0 – 5 V
10Diagnosis selection inputWhen MUT-II is connected1 V or less
When MUT-II is disconnectedSystem voltage
11Stop lamp switchIgnition switch:
ON
Stop lamp switch: ONSystem voltage
ON
Stop lamp switch: OFF1 V or less
12*1ABS monitorWhen ABS monitor is activatedSystem voltage
When ABS monitor is deactivated1 V or less

REAR AXLE – Troubleshooting <AYC>27-29
Terminal
No.Normally Check requirement Check item
17Steer sensor (ST-N)Engine:
Idle speed
Steering wheel: Neutral position0.5 V or less
Idle speed
Steering wheel: Turned 90 from
neutral position2.5 – 3.5 V
18TPSIgnition switch:
ON
Accelerator pedal: Fully closed0.3 – 1.0 V
ON
Accelerator pedal: Fully open4.5 – 5.0 V
23Diagnosis data input/outputWhen MUT-II is connectedSerial communica-
tion with MUT-II
When MUT-II is disconnected1 V or less
24Idle position switchIgnition switch:
ON
Accelerator pedal: Fully closed2 V or less
ON
Accelerator pedal: Fully open4.5 – 5.0 V
25Accumulator pressure
switchIgnition switch:
ONAccumulator internal pressure:
Low2 V or less
Accumulator internal pressure:
HighSystem voltage
26ECU groundAt all times0 V
31AYC-ECU power supplyIgnition switch: ONSystem voltage
Ignition switch: OFF0 V
35AYC motor relayIgnition switch:
ON
When motor is energizedSystem voltage
ON
When motor is deenergized2 V or less
36AYC warning lampIgnition switch:
ON
When lamp is OFFSystem voltage
ON
When lamp is ON2 V or less
37Directional control valve
(right)
Ignition switch:
ON
Right clutch: ONSystem voltage
(right)ON
Right clutch: OFF0 V
38Proportioning valveIgnition switch:
ONAYC-ON0 V to system volt-
age
AYC-OFF0 V
39ECU backup power supplyAt all timesSystem voltage
45Directional control valve
(left)
Ignition switch:
ON
Left clutch: ONSystem voltage
(left)ON
Left clutch: OFF0 V
46ECU groundAt all times0 V
NOTE
*1: Indicates the vehicles with ABS.