service MITSUBISHI LANCER EVOLUTION VI 1999 Manual PDF

REAR AXLE – Hydraulic Unit <Vehicles with AYC>27-40
REMOVAL SERVICE POINTS
AHYDRAULIC UNIT REMOVAL
Should the hydraulic unit be discarded, drill a hole in the
accumulator at the illustrated position beforehand in order
to release the inside gas.
Caution
(1) The hydraulic unit has its accumulator filled with a
high pressure gas. Never throw it into a fire. Also,
never attempt to disassemble, press, weld or melt
it.
(2) When drilling a hole in the accumulator, be sure to
wear safety goggles since drill chips may blow out
together with the gas.
INSTALLATION SERVICE POINTS
AGROMMET INSTALLATION
On the vehicle mounted with a sunroof, mount the drain pipe
to the grommet as illustrated.
BSUCTION HOSE / RETURN HOSE INSTALLATION
Fit the suction hose and return hose to the nipple of hydraulic
unit as illustrated.
CHYDRAULIC UNIT AND BRACKET ASSEMBLY
INSTALLATION
Hook the hydraulic unit bracket hook to the rear floor side
member and install the hydraulic unit and bracket assembly
mounting bolt.Grommet
Drain pipe
25 ± 5 mm
Nipple
Suction hose and
return hose15 mm
Hook
Rear floor side member

REAR AXLE – Sensor Relay <Vehicles with AYC>27-41
SENSOR RELAY <VEHICLES WITH AYC>
REMOVAL AND INSTALLATION
Caution: SRS
For vehicles with SRS, before removal of air bag module and clock spring, refer to GROUP 52B
– Service Precautions and Air Bag Module and Clock Spring.
12
3
4
Steer sensor removal steps

Steering wheel and column cover
A1. Steer sensorAcceleration sensor and AYC relay
removal
2. Longitudinal acceleration sensor
3. Lateral acceleration sensor
4. AYC relay
NOTE
For the wheel speed sensor, refer to GROUP 35B.
REMOVAL SERVICE POINT
ASTEER SENSOR REMOVAL
Remove the steer sensor from the column switch.
Caution
(1) A photocoupler is used as the steer sensor. Use care
not to allow dust or grease to be on the sensor.
(2) Do not bend or dirty with grease the slit plate on
the column switch side.Slit plate
Steer sensor

FRONT SUSPENSION – General / Lower Arm <EVOLUTION-VI>33A-1
GROUP 33A
FRONT SUSPENSION
GENERAL
OUTLINE OF CHANGE

The installation method of the ball joint between the knuckle and the lower arm has been changed,
and accordingly the removal and installation procedures of the lower arm have been revised.
<EVOLUTION-VI>
LOWER ARM <EVOLUTION-VI>
REMOVAL AND INSTALLATION
Caution
The part marked with * should be first temporarily tightened, then torqued to specification with the vehicle
on the ground in unloaded condition.
Post-installation Operation

Push the Dust Cover of the Lower Arm and Stabilizer Link Ball Joint with a Finger to Check for Possible Cracks or Damage.

Wheel Alignment Check and Adjustment
1
2
3
4
5
6
39 Nm
106 Nm*
5
98 – 118 Nm
74 – 87 Nm88 Nm
137 Nm
Removal steps
1. Stabilizer link mounting nut
2. Bolt
3. Stabilizer bracket
A4. Bushing assembly
5. Lower arm assembly6. Lower arm bracket assembly
NOTE
Follow the conventional procedures for installation service
points.

35A-1
BASIC BRAKE
SYSTEM
CONTENTS
GENERAL 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Outline of Change 2. . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE 2. . . . . . . . . . . . . . . . . .
Brake Pedal Check and Adjustment 2. . . . . . . .
BRAKE PEDAL 4. . . . . . . . . . . . . . . . . . . . . . . . . . MASTER CYLINDER AND BRAKE
BOOSTER 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Master Cylinder 7. . . . . . . . . . . . . . . . . . . . . . . . . . .
DISC BRAKE 9. . . . . . . . . . . . . . . . . . . . . . . . . . . .

BASIC BRAKE SYSTEM – General / On-vehicle Service35A-2
GENERAL
OUTLINE OF CHANGE

The service procedures for left-hand drive vehicles have been established as described below.

The service procedures for the front and rear disc brakes have been changed since they had been
replaced by a different type. <EVOLUTION-VI with BREMBO braking system>
ON-VEHICLE SERVICE
BRAKE PEDAL CHECK AND ADJUSTMENT
<L.H. DRIVE VEHICLES>
1. Turn up the carpet, etc under the brake pedal.
2. Measure the brake pedal height as illustrated. If the brake
pedal height is not within the standard value, follow the
procedure below.
Standard value: 163.5 –166.5 mm
(1) Disconnect the stop lamp switch connector.
(2) Adjust the brake pedal height by turning the operating
rod with pliers (with the operating rod lock nut
loosened), until the correct brake pedal height is
obtained.
(3) Secure by tightening the lock nut of the operating
rod.
(4) Push the stop lamp switch in the direction of the
pedal stroke until it stops. (The switch will slide if
it is pushed firmly.)
(5) Lift up the pedal until the operating rod is fully
extended, and then slide the stop lamp switch back
to the required position. Adjust the position of the
switch by turning it until the distance shown in the
illustration is correct.
(6) Connect the connector of the stop lamp switch.
(7) Check that the stop lamp is not illuminated with the
brake pedal unpressed.
3. With the engine stopped, depress the brake pedal two
or three times. After eliminating the vacuum in the power
brake booster, press the pedal down by hand, and confirm
that the amount of movement before resistance is met
(the free play) is within the standard value range.
Standard value: 3 – 8 mmOperating
rod
Operating
rod lock nutStop lamp
switch
Pedal down
Pedal up
Lock nut
Lock nut
Outer case
0.5 – 1.0 mm

BASIC BRAKE SYSTEM – On-vehicle Service35A-3
If the free play exceeds the standard value, it is probably
due to excessive play between the retaining ring bolt
and brake pedal arm.
Check for excessive clearance and replace faulty parts
as required.
4. Start the engine, depress the brake pedal with
approximately 490 N of force, and measure the clearance
between the brake pedal and the floorboard.
Standard value: 80 mm or more
If the clearance is outside the standard value, check for
air trapped in the brake line, clearance between the lining
and the drum and dragging in the parking brake.
Adjust and replace defective parts as required.
5. Turn back the carpet, etc.

BASIC BRAKE SYSTEM – Master Cylinder and Brake Booster35A-6
INSTALLATION SERVICE POINTS
AVACUUM HOSE CONNECTION
Insert securely and completely until the vacuum hose at the
engine side contacts the edge of the hexagonal part of the
fitting, and then secure by using the hose clip.
BCLEARANCE ADJUSTMENT BETWEEN BRAKE
BOOSTER PUSH ROD AND PRIMARY PISTON
Calculate clearance A from the B, C and D measurements.
A = B – C – D
Standard value: 0.65–0.85 mm
If the clearance is not within the standard value range, adjust
by changing the push rod length by turning the screw of
the push rod.
Measuring
distance BMeasuring
distance D
Block
gaugeB
AC
D

BASIC BRAKE SYSTEM – Master Cylinder and Brake Booster35A-8
DISASSEMBLY SERVICE POINTS
APISTON STOPPER BOLT DISASSEMBLY
Remove the piston stopper bolt, while depressing the piston.
BPISTON STOPPER RING DISASSEMBLY
Remove the piston stopper ring, while depressing the piston.
INSPECTION

Check the inner surface of master cylinder body for rust
or pitting.

Check the primary and secondary pistons for rust, scoring,
wear, damage or wear.

Check the diaphragm for cracks and wear.

37A-1
STEERING
CONTENTS
GENERAL 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Outline of Change 2. . . . . . . . . . . . . . . . . . . . . . . . .
STEERING WHEEL AND SHAFT* 2. . . . . . . .
POWER STEERING GEAR BOX* 5. . . . . . . . .
WARNINGS REGARDING SERVICING OF SUPPLEMENTAL RESTRAINT SYSTEM (SRS) EQUIPPED VEHICLES
WARNING!
(1) Improper service or maintenance of any component of the SRS, or any SRS-related component, can lead to personal
injury or death to service personnel (from inadvertent firing of the air bag) or to the driver and passenger (from rendering
the SRS inoperative).
(2) Service or maintenance of any SRS component or SRS-related component must be performed only at an authorized
MITSUBISHI dealer.
(3) MITSUBISHI dealer personnel must thoroughly review this manual, and especially its GROUP 52B – Supplemental
Restraint System (SRS) before beginning any service or maintenance of any component of the SRS or any SRS-related
component.
NOTE
The SRS includes the following components: SRS-ECU, SRS warning lamp, air bag module, clock spring and interconnecting
wiring. Other SRS-related components (that may have to be removed/installed in connection with SRS service or maintenance) are
indicated in the table of contents by an asterisk (*).

STEERING – General / Steering Wheel and Shaft37A-2
GENERAL
OUTLINE OF CHANGE

The service procedures for left-hand drive vehicles have been established as described below. The
service procedures for components not mentioned below are the same as for the preceding models.
STEERING WHEEL AND SHAFT <L.H. DRIVE VEHICLES>
REMOVAL AND INSTALLATION
CAUTION: SRS
For vehicles with SRS, before removal of air bag module, refer to GROUP 52B – Service Precautions and
Air Bag Module and Clock Spring.
Pre-removal Operation
Instrument Under Cover RemovalPost-installation Operation

Instrument Under Cover Installation

Checking Steering Wheel Position with Wheels
Straight Ahead
<Vehicles without SRS>
5 Nm
17 Nm11 Nm
<Vehicles with SRS>
10
98 431
532
41 Nm
25 Nm
6
25 Nm41 Nm
7
9 Nm
Section A – A Section B – B
Claw
: Claw position
AB 4
5
AB
11 Nm 21 Nm Standard bolt Earth bolt
NOTE
4
5
Claw
Removal steps
1. Horn pad <Vehicles without SRS>
2. Air bag module
(Refer to GROUP 52B – Air Bag
Module and Clock Spring.)
A3. Steering wheel
4. Upper column cover
5. Lower column coverA6. Column switch
<Vehicles without SRS>
A7. Clock spring and column switch
(Refer to GROUP 52B – Air Bag
Module and Clock Spring.)
8. Steering shaft assembly
9. Band
10. Steering cover assembly