service MITSUBISHI LANCER EVOLUTION VI 1999 Service Manual

ENGINE – Starter Motor11-84
DISASSEMBLY SERVICE POINTS
AMAGNETIC SWITCH REMOVAL
Disconnect field coil wire from “M” terminal of magnetic switch.
BARMATURE / BALL REMOVAL
Caution
When removing the armature, take care not to lose the
ball (which is used as a bearing) in the armature end.
CSNAP RING / STOP RING REMOVAL
(1) Press stop ring off snap ring with a suitable socket.
(2) Remove snap ring with snap ring pliers and then remove
stop ring and overrunning clutch.
STARTER MOTOR PARTS CLEANING
(1) Do not immerse parts in cleaning solvent. Immersing the
yoke and field coil assembly and/or armature will damage
insulation. Wipe motor assembly with a cloth only.
(2) Do not immerse drive unit in cleaning solvent. Overrunning
clutch is pre-lubricated at the factory and solvent will wash
lubrication from clutch.
(3) The drive unit may be cleaned with a brush moistened
with cleaning solvent and wiped dry with a cloth.
Magnetic
switch“S” terminal
“B” terminal
Field coil wire “M” terminal
Stop ringSocket
Pinion gear
Overrunning
clutch
Armature
Snap ring
Pinion gear
Overrunning
clutchSnap ring pliers
Armature

ENGINE – Starter Motor11-85
REASSEMBLY SERVICE POINTS
ASTOP RING / SNAP RING INSTALLATION
Using a suitable pulling tool, pull overrunnig clutch stop ring
over snap ring.
INSPECTION
COMMUTATOR CHECK
(1) Place the armature in a pair of “V” blocks and check
the runout with a dial indicator.
Standard value: 0.05 mm
Limit: 0.1 mm
(2) Measure the commutator outer diameter.
Standard value: 32.0 mm
Limit: 31.4 mm
(3) Check the undercut depth between segments.
Standard value: 0.5 mm
BRUSH HOLDER CHECK
Check the continuity between brush holder plate and brush
holder.
If there is no continuity, the brush holder is in order.
Stop ringOverrunning
clutchStop ring
Snap ring
Undercut
Segment
Mica
Brush holder

13-1
FUEL
CONTENTS
MULTIPOINT INJECTION (MPI) 2. . . . . . .
GENERAL 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Outline of Change 2. . . . . . . . . . . . . . . . . . . . . . . . .
SERVICE SPECIFICATIONS 4. . . . . . . . . . . . . .
SEALANT 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS 5. . . . . . . . . . . . . . . . . . . . . . . .
TROUBLESHOOTING 6. . . . . . . . . . . . . . . . . . . . ON-VEHICLE SERVICE 68. . . . . . . . . . . . . . . .
Fuel Pump Resistor Check 68. . . . . . . . . . . . . . . .
Fuel Pump Relay No.2
Continuity Check 68. . . . . . . . . . . . . . . . . . . . . . . . .
Engine Control Relay and Fuel Pump Relay
Continuity Check 68. . . . . . . . . . . . . . . . . . . . . . . . .
FUEL SUPPLY 69. . . . . . . . . . . . . . . . . . . . .
GENERAL 69. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Outline of Change 69. . . . . . . . . . . . . . . . . . . . . . . .
FUEL TANK 69. . . . . . . . . . . . . . . . . . . . . . . . . . .

MPI – General13-2
MULTIPOINT INJECTION (MPI)
GENERAL
OUTLINE OF CHANGE

The descriptions of the troubleshooting using an MUT-II tester have been added.

The fuel system and its management of EVOLUTION-VI are different from those of EVOLUTION-V
in the following items. Accordingly, the service procedures for these items are described herein. The
service procedures for the remaining item are the same as those for EVOLUTION-V.

Fan motor control

Fuel pump drive control

Fuel pump relay No.2

Fuel pump resistor

Actuator test function of MUT-II (The test of the following items has been made possible.)
a) Item No.36: Secondary air control solenoid valve
b) Item No.37: Air conditioner condenser fan (High)
c) Item No.38: Air conditioner condenser fan (Low)

MPI – Service Specifications / Sealant13-4
SERVICE SPECIFICATIONS
ItemsSpecifications
Basic ignition timing BTDC5 ± 3
Basic idle speed rpm850 ± 50
Throttle position sensor adjusting voltage mV400 – 1,000
Throttle position sensor resistance kΩ3.5 – 6.5
ISC servo coil resistance (at 20C) Ω28 – 33
Intake air temperature sensor resistance kΩAt 20C2.3 – 3.0
At 80C0.30 – 0.42
Coolant temperature sensor resistance kΩAt 20C2.1 – 2.7
At 80C0.26 – 0.36
Fuel pressure kPaWhen vacuum hose is connected230
When vacuum hose is disconnected289 – 309
Injector coil resistance Ω2 – 3
Amount of injector fuel leak drop/min1 or less
Oxygen sensor output voltage V0.6 – 1.0
Fuel pressure control valve coil resistance (at 20C) Ω28 – 36
SEALANT
ItemSpecified sealantRemark
Engine coolant temperature sensor
threaded portion3M Nut Locking Part No.4171 or equivalentDrying sealant

MPI – Troubleshooting13-6
TROUBLESHOOTING
DIAGNOSIS TROUBLESHOOTING FLOW
Refer to GROUP 00 – How to Use Troubleshooting/Inspection
Service Points.
DIAGNOSIS FUNCTION
ENGINE WARNING LAMP (CHECK ENGINE LAMP)
If an abnormality occurs in any of the following items related
to the Multipoint Fuel Injection (MPI) system, the engine
warning lamp will illuminate.
If the lamp remains illuminated or if the lamp illuminates while
the engine is running, check the diagnosis code output.
Engine warning lamp inspection items
Engine-ECU
Air flow sensor
Intake air temperature sensor
Throttle position sensor
Engine coolant temperature sensor
Crank angle sensor
Camshaft position sensor
Barometric pressure sensor
Detonation sensor
Injector
Ignition coil, power transister unit
METHOD OF READING AND ERASING DIAGNOSIS
CODES
Refer to GROUP 00 – How to Use Troubleshooting/Inspection
Service Points.
INSPECTION USING MUT-II DATA LIST AND
ACTUATOR TESTING
1. Carry out inspection by connecting the MUT-II.
If there is an abnormality, check and repair the chassis
harnesses and components.
2. After repairing, check that the abnormal input and output
have returned to normal as a result of the repairs.
3. Erase the diagnosis code memory.
4. Remove the MUT-II and carry out a road test to confirm
that the problem has disappeared.
Engine warning lamp
(check engine lamp)

MPI – Troubleshooting13-39
INSPECTION PROCEDURE 28
Power steering fluid pressure switch system
Probable cause
The presence or absence of power steering load is input to the engine-ECU.
The engine-ECU controls the idle speed control (ISC) servo based on this input.
Malfunction of power steering fluid pressure switch

Improper connector contact, open or short-circuited
harness wire

Malfunction of the engine-ECU
Check the power steering fluid pressure switch.NG
Replace
OK
Measure at the power steering fluid pressure switch connector
A-101.

Disconnect the connector, and measure at the harness side.

Voltage between 1 and earth (Ignition switch: ON)
OK:System voltageNGCheck the following
connectors: A-28, B-60NG
Repair
OK
Check trouble symptom.
NG
Check harness wire be-
tween engine-ECU and
power steering fluid pres-
sure switch connector.NG
Repair
OK
Replace the engine-ECU.
OK
Check the following
connector: A-101NG
Repair
OK
Check trouble symptom.
NG
Replace the engine-ECU.
INSPECTION PROCEDURE 29
A/C switch and A/C relay system
Probable cause
When an A/C ON signal is input to the engine-ECU, the engine-ECU carries out
control of the idle speed control (ISC) servo, and also operates the A/C compressor
magnetic clutch.
Malfunction of A/C control system

Malfunction of A/C switch

Improper connector contact, open or short-circuited
harness wire

Malfunction of the engine-ECU
Check the A/C compressor relay.
(Refer to GROUP 55 – On-vehicle Service.)NG
Replace
OK
Measure at the engine-ECU connectors B-59, B-60.

Disconnect the connector, and measure at the harness side.

Voltage between 22 and earth, and 45 and earth
(Ignition switch: ON, A/C switch: ON)
OK:System voltage

Short-circuit between 22 and earth
(Ignition switch: ON, A/C switch: ON)
OK:A/C compressor clutch turns on.NGCheck the A/C system. (Refer to GROUP 55 – On-vehicle Service.)
OKCheck the following
connectors: B-59, B-60NG
Replace
OK
Check trouble symptom.
NG
Replace the engine-ECU.

MPI – Troubleshooting13-45
INSPECTION PROCEDURE 34
Fuel pressure control valve system
Probable cause
The fuel pressure control valve switches the pressure introduction into the fuel pressure
regulator between the intake manifold and atmosphere.
Malfunction of solenoid valve

Improper connector contact, open or short-circuited
harness wire

Malfunction of engine-ECU
NGReplace the engine-ECU.
OK
Check trouble symptom.
NG
Check the harness wire between engine-ECU and solenoid valve
connector, and repair if necessary.
OK
Check trouble symptom.
OK
Check the following connector: B-59NG
Repair
OK
Measure at the engine-ECU connector B-59.

Disconnect the connector, and measure at the harness side.

Voltage between 3 and earth
(Ignition switch: ON)
OK:System voltageNGCheck the following connector: A-12NG
Repair NG
Check the harness wire between control relay and solenoid valve
connector, and repair if necessary.
OK
Measure at the fuel pressure control valve connector A-12.

Disconnect the connector, and measure at the harness side.

Voltage between 1 and earth
(Ignition switch: ON)
OK:System voltage
Check the fuel pressure control valve.NG
Replace
INSPECTION PROCEDURE 35
Waste gate solenoid valve
Probable cause
The waste gate solenoid valve controls the boost pressure introduced into the waste
gate actuator in the turbocharger.
Malfunction of solenoid valve

Improper connector contact, open or short-circuited
harness wire

Malfunction of engine-ECU
NGReplace the engine-ECU.
OK
Check trouble symptom.
NG
Check the harness wire between engine-ECU and solenoid valve
connector, and repair if necessary.
OK
Check trouble symptom.
OK
Check the following connector: B-59NG
Repair
OK
Measure at the engine-ECU connector B-59.

Disconnect the connector, and measure at the harness side.

Voltage between 11 and earth
(Ignition switch: ON)
OK:System voltageNGCheck the following connector: A-23NG
Repair NG
Check the harness wire between control relay and solenoid valve
connector, and repair if necessary.
OK
Measure at the waste gate solenoid valve connector A-23.

Disconnect the connector, and measure at the harness side.

Voltage between 2 and earth
(Ignition switch: ON)
OK:System voltage
Check the waste gate solenoid valve.
(Refer to Group 15 – On-vehicle service.)*NG
Replace
NOTE
*: Refer to Workshop Manual for LANCER EVOLUTION-IV and EVOLUTION-V (Pub. No. S9806CNCP9).

MPI – On-vehicle Service13-68
ON-VEHICLE SERVICE
FUEL PUMP RESISTOR CHECK

Standard value: 0.45 – 0.65 Ω
The inspection procedures are the same as for the preceding
year-models.
FUEL PUMP RELAY No.2 CONTINUITY CHECK

Battery voltageTerminal No.
1234
Not supplied
Supplied
ENGINE CONTROL RELAY AND FUEL PUMP
RELAY CONTINUITY CHECK
Battery voltageTerminal No.
1234
Not supplied
Supplied
Equipment side connector for engine
control relay and fuel pump relay
Fuel pump relay
Engine control relay

FUEL SUPPLY – General / Fuel Tank13-69
FUEL SUPPLY
GENERAL
OUTLINE OF CHANGE
The service procedures have been revised as shown below because of change in the fuel pump & gauge
assembly and the fuel gauge unit.
FUEL TANK
REMOVAL AND INSTALLATION
4
32 1
65
7
11
Removal steps
1. Fuel hose
2. Fuel pump & gauge assembly
3. Packing
A4. High-pressure fuel hose5. Fuel pipe assembly
6. Fuel gauge unit
7. Packing
NOTE
The service procedures other than those mentioned above
remain unchanged.
INSTALLATION SERVICE POINT
AHIGH-PRESSURE FUEL HOSE INSTALLATION
Caution
After connecting the quick-release joint of the
high-pressure fuel hose, pull it gently in the direction
of removal to check that the hose is firmly connected
with a play of about 3 mm.