voltage MITSUBISHI LANCER EVOLUTION VI 1999 Manual PDF

BODY – Keyless Entry System42-4
INSPECTION PROCEDURE 2
All of the doors can be locked and unlocked using the
transmitter, but the room lamp does not flash or
illuminate. (However, the room lamp operates normally
when the doors are opened and closed.)
Probable cause
If the room lamp operates normally when the doors are opened and closed, the cause
of the problem may be a malfunction of the receiver or a malfunction of the harness
between the room lamp the receiver.
Malfunction of receiver

Malfunction of connector or wiring harness
NG
Repair
NG
Check the harness wire between room lamp and receiver, and
repair if necessary.
OK
Replace the receiver.
OK
Check trouble symptoms.
Measure at the receiver connector D-01.

Disconnect the connector, and measure at the harness side.

Voltage between 11 and body earth
OK:System voltageNGCheck the following connectors:
B-80, D-01
INSPECTION PROCEDURE 3
Secret codes cannot be registered.
Probable cause
The cause may be a malfunction of the diagnosis connector, a malfunction of the
power supply or earth circuit of the receiver, a malfunction of the earth circuit or
a malfunction of the diagnosis output circuit.
Malfunction of receiver

Malfunction of MUT-II

Malfunction of connector or wiring harness
NG
Repair
NG
Check the harness wire, and repair if necessary.

Between receiver and diagnosis connector
NG
Repair
NG
Check the harness wire, and repair if necessary.

Between fusible link No.1 and diagnosis connector
OK
Check trouble symptoms.NGCheck the harness wire, and repair if necessary.

Between diagnosis connector and earth
Ye s
To next page
NG
Check the following
connectors:
B-22, B-50NG
Repair
OK
Measure at the diagnosis
connector B-22.

Continuity between 4
and body earth

Continuity between 5
and body earth
OK:ContinuityOKReplace MUT-II.
OK
Check trouble symptoms.
No
Measure at the diagnosis
connector B-22

Voltage between 16
and body earth
OK:System voltageNGCheck the following connectors:
B-22, B-49, B-75
OK
Can the MUT-II communicate with other systems?
OK
Check trouble symptoms.
Measure at the diagnosis connector B-22 and the receiver connector
D-01.

Disconnect the connector, and measure at harness side.

Continuity between following terminals:
OK:Continuity
7 <Receiver side> – 1 <Diagnosis connector side>NGCheck the following connectors:
B-22, D-01

BODY – Keyless Entry System42-5
NG
Repair
NG
Check the harness wire, and repair if necessary.

Between fusible link No.1 and receiver

Between ignition switch and receiver
NG
Repair
NG
Check the harness wire, and repair if necessary.

Between receiver and earth
OK
Replace the receiver.
OK
Check trouble symptoms.
OK
Measure at the receiver connector D-01.

Disconnect the connector, and measure at the harness side.

Between 20 and body earth
OK:ContinuityNGCheck the following connectors:
B-50, D-01
OK
Check trouble symptoms.
Measure at the receiver connector D-01.

Disconnect the connector, and measure at the harness side.

Voltage between 9 and body earth

Voltage between 10 and body earth
OK:System voltageNGCheck the following connectors:
B-49, B-75, D-01
From previous page
INSPECTION OF RECEIVER TERMINAL VOLTAGE
TerminalSignal nameConditionsTerminal voltage
2Door switchOne or more doors are open (Door switch: ON)0 V
All doors are closed (Door switch: OFF)System voltage
6Door lock actuator
switch (driver’s side)
LOCK5 V and pulse output*
switch (driver’s side)
UNLOCK0 V
7Diagnosis changeover
input
When MUT-II is connected0 V
input
When MUT-II is disconnectedSystem voltage
8Key reminder switchOFF (When ignition key is inserted)5 V and pulse output*
ON (When ignition key is removed)0 V
9Ignition switchIgnition switch: ACC or ONSystem voltage
Ignition switch: OFF0 V
10Receiver power supplyAt all timesSystem voltage
11Room lamp outputOne or more door are open (Door switch: ON)0 V
All doors are closed (Door switch: OFF)System voltage

BODY – Keyless Entry System42-6
TerminalSignal nameConditionsTerminal voltage
12Door lock outputWhen activated0 V
When not activatedSystem voltage
14Door unlock outputWhen activated0 V
When not activatedSystem voltage
20EarthAt all times0 V
NOTE
Values marked with * should be measured using an oscilloscope. (The value will alternate between 0
V and 0.03 V if a circuit tester is used.)

BODY – Sunroof42-10
OK
Check trouble symptoms.
NG
Check the harness wire between igni-
tion switch (IG1) and sunroof-ECU, and
repair if necessary.
(2) NG
Check the following connectors:
B-44, B-76, B-73, D-10NG
Repair
OK
Check trouble symptoms.
NG
Check the harness wire between fusible
link No.1 and sunroof-ECU, and repair
if necessary.
(3) NG
Check the following connectors:
B-44, D-10NG
Repair
OK
Check trouble symptoms.
NG
Check the harness wire between sunroof-ECU and
the earth, and repair if necessary.
OK
Check sunroof switch continuity (Refer to P.42-17.)NG
Repair
OK
Measure at the sunroof-ECU connector D-10.

Disconnect the connector and measure at the harness side.

Continuity between 2 and body earth
OK:Continuity present when UP sunroof switch is on

Continuity between 3 and body earth
OK:Continuity present when CLOSE/DOWN sunroof switch
is on

Continuity between 4 and body earth
OK:Continuity present when OPEN sunroof switch is onNGCheck the following connectors:
D-10, D-07NG
Repair
OK
Check trouble symptoms.
NG
Check the harness wire between sun-
roof-ECU and sunroof switch, between
sunroof switch and the earth, and repair
if necessary.
OK
Check the sunroof motor. (Refer to P.42-17.)
Check limit switch continuity. (Refer to P.42-17.)NG
Replace
OK
Measure at the sunroof motor connector D-12.

Disconnect the connector and measure at the harness side.

Continuity between 4 and body earth
OK:ContinuityNGCheck the following connectors:
B-44, D-12NG
Repair
OK
Check trouble symptoms.
NG
Check the harness wire between sun-
roof motor and the earth, and repair
if necessary.
OK
Check the following connectors:
D-12, D-10NG
Repair
OK
Check trouble symptoms.NGCheck the harness wire between sun-
roof-ECU and sunroof motor.NG
Repair
OK
Replace the sunroof-ECU.
Measure at the sunroof-ECU connector D-10.

Disconnect the connector and measure at the harness side.

Ignition switch: ON
(1) Voltage between 5 and body earth
OK:System voltage
(2) Voltage between 7 and body earth
OK:System voltage
(3) Continuity between 18 and body earth
OK:Continuity(1) NGCheck the following connectors:
B-44, B-74, B-76, D-10NG
Repair

BODY – Sunroof42-11
Inspection Procedure 2
The motor does not reverse its direction when a load of
140 N or more is applied while the sunroof is closing.
Probable cause
The sunroof-ECU monitors the load conditions from the amount of current flowing
to the motor. If more than the constant amount of current is flowing, the direction
of motor operation is reversed to prevent jamming.
If the motor does not reverse direction even when an excessive load is being applied,
the cause may be a malfunction of the sunroof-ECU.
Malfunction of sunroof-ECU
Replace the sunroof-ECU.
Inspection Procedure 3
The timer does not operate for 30 seconds after the
ignition switch is turned to OFF.
Probable cause
The sunroof-ECU has a timer function which operates for 30 seconds after the ignition
switch is turned to OFF. If the timer does not operate, the cause may be a malfunction
of the sunroof-ECU or of the wiring harness or connector.
Malfunction of sunroof-ECU

Malfunction of wiring harness or connector
Measure at the sunroof-ECU connector
D-10.

Disconnect the connector and
measure at the harness side.

Voltage between 7 and body earth
OK:System voltageNGCheck the following connectors:
B-44, B-76, B-73NG
Repair
OK
Check trouble symptoms.
OK
Replace the sunroof-ECU.
Check the harness wire between fusible
link No.1 and sunroof-ECU, and repair
if necessary. NG
Inspection Procedure 4
Opening or closing of the sunroof is possible for 30
seconds after turning the ignition switch to OFF, but the
timer function is not extended when the driver’s side door
is opened within this period.
Probable cause
The sunroof timer operation period is extended when an on signal is output from
the driver’s-side door switch. Because of this, if the timer operation period is not
extended, the cause may be a malfunction of the door switch input circuit.
Malfunction of the front door switch (driver’s side)

Malfunction of sunroof-ECU

Malfunction of wiring harness or connector
Check front door switch (driver’s side)
continuity.NG
Replace
OK
Check the following connectors:
B-44, D-03, D-10NG
Repair
OK
Check trouble symptoms.NGCheck the harness wire between front
door switch (driver’s side) and sunroof-
ECU.NG
Repair
OK
Replace the sunroof-ECU.

BODY – Sunroof42-12
TERMINAL VOLTAGE CHART
Terminal No.Check ItemCheck ConditionNormal Condition
1Door switch inputDriver’s door switchON0 V
OFFSystem voltage
2Sunroof switch (up) inputSunroof switch
(up position)
ON0 V
(up position)
OFFSystem voltage
3Sunroof switch (close or
down) input
Sunroof switch (close
position or down position)
ON0 V
down) inputposition or down position)
OFFSystem voltage
4Sunroof switch (open
input)
Sunroof switch
(open position)
ON0 V
input)(open position)
OFFSystem voltage
5ECU power supplyIgnition switch: ONSystem voltage
6Motor output (When
sunroof is opening)While sunroof is opening or moving
downSystem voltage
Other than the above0 V
7Timer operation power
supplyAlwaysSystem voltage
8Motor output (When
sunroofis closing)
While sunroof is closing or moving upSystem voltage
sunroof is closing)
Other than the above0 V
9Limit switch 3 inputIn tilt up condition and fully-open
condition0 V
Other than the aboveSystem voltage
10Limit switch 1 inputIn tilt up conditionSystem voltage
In fully-closed and fully-open conditions0 V
In slide-closing condition0 V → System voltage →
0V.
12Limit switch 2 inputIn tilt up condition and fully-closed
conditionSystem voltage
Other than the above0 V
18EarthAlways0 V

SRS – SRS Service Precautions52B-3
SRS SERVICE PRECAUTIONS
1. In order to avoid injury to yourself or others
from accidental deployment of the air bag during
servicing, read and carefully follow all the
precautions and procedures described in this
manual.
2. Do not use any electrical test equipment on
or near SRS components, except those
specified on P.52B-5.
3. Never Attempt to Repair the Following
Components:

SRS air bag control unit (SRS-ECU)

Clock Spring

Air Bag Module
(Driver‘s side or front passenger’s side*)NOTE
*: Vehicles with front passenger’s air bag
If any of these components are diagnosed as
faulty, they should only be replaced, in
accordance with the INDIVIDUAL COM-
PONENT SERVICE procedures in this manual,
starting at page 52B-22.
4. After disconnecting the battery cable, wait 60 seconds
or more before proceeding with the following work.
The SRS system is designed to retain enough voltage
to deploy the air bag for a short time even after the
battery has been disconnected, so serious injury may
result from unintended air bag deployment if work
is done on the SRS system immediately after the
battery cables are disconnected.
5. Do not attempt to repair the wiring harness connectors
of the SRS. If any of the connectors are diagnosed as
faulty, replace the wiring harness. If the wires are
diagnosed as faulty, replace or repair the wiring harness
according to the following table.
Battery Insulating tape
SRS-ECU connector

SRS – Troubleshooting52B-9
Code No.24, 25, 64 or 65 Front passenger’s side air bag
module (squib) systemProbable cause
These diagnosis codes are output if there is abnormal resistance between the input
terminals of the driver’s side air bag module (squib).
The trouble causes for each diagnosis code No. are as follows.
Malfunction of wiring harnesses or connectors

Malfunction of front passenger’s side air bag module
(squib)

Malfunction of SRS-ECU
Code No.Trouble symptom
24
Short in front passenger’s side air bag module (squib) or harness short

Malfunction of connector*
25
Open circuit in front passenger’s side air bag module (squib) or open harness

Malfunction of connector contact
64
Short in front passenger’s side air bag module (squib) harness leading to the power
supply
65
Short in front passenger’s side air bag module (squib) harness leading to the earth
NOTE
*: The connector in the squib circuit has a built-in short bar which short-circuits between plus (+) lead and minus
(–) lead of the squib circuit when the connector is not being connected to prevent an accidental air bag deployment
possibly caused by static electricity, etc. Therefore, malfunction of the connector can also be caused by this
short bar which fails to be released even when the connector is reconnected if it is damaged.
OK
Check trouble symptoms.
NG
Check the harness wire
between the front passen-
ger’s side air bag module
(squib) and SRS-ECU.NG
Repair
OK
Replace the SRS-ECU.
Ye sCheck the following
connectors:
B-01, B-51NG
RepairSRS check harness
(MB991613)
Body
wiring
harness
1
No
Replace the front passenger’s side air bag module.MUT-II Self-diag code

Disconnect front
passenger’s side air bag
module connector B-01.

Connect SRS check
harness connector (1).

Erase diagnosis code
memory.
Are code Nos.24, 25, 64 or 65
output?
Code No.31 or 32 SRS-ECU capacitor systemProbable cause
Probable cause
These diagnosis codes are output if there is abnormal resistance between the input
terminals of the driver’s side air bag module (squib).
Malfunction of SRS-ECU
Code No.Trouble symptom
31
Voltage at the capacitor terminal is higher than the specified value for five seconds
or more
32
Voltage at the capacitor terminal is lower than the specified value for five seconds
or more (this is not detected if diagnosis code No.41 or 42 indicating system voltage
drop has been output.)
Replace the SRS-ECU.

SRS – Troubleshooting52B-10
Code No.34 Connector lock systemProbable cause
This diagnosis code is output if a poor connection of the SRS-ECU is detected. However,
if the vehicle condition returns to normal, diagnosis code No.34 will be automatically
erased, and the SRS warning lamp will switch off.
Malfunction of connectors

Malfunction of SRS-ECU
Is B51 SRS-ECU connector correctly connected?Ye s
No
Repair
Check the following connector:
B-51
OK
Replace the SRS-ECU.ReplaceNG
Code No.35 SRS-ECU (deployed air bag) systemProbable cause
This diagnosis code is output after the air bag deploys. If this code is output before
the air bag has deployed, the cause is probably a malfunction inside the SRS-ECU.
Malfunction of SRS-ECU
Replace the SRS-ECU.
Code No.41 IG1 (A) power circuit systemProbable cause
This diagnosis code is output if the voltage between the IG1 (A) terminal and the
earth is lower than the specified value for a continuous period of 5 seconds or more.
However, if the vehicle condition returns to normal, diagnosis code No.41 will be
automatically erased, and the SRS warning lamp will switch off.
Malfunction of wiring harnesses or connectors

Malfunction of SRS-ECU
Measure at SRS check harness
connector (5).

Disconnect SRS-ECU
connector B-51.

Connect SRS check
harness connector (3).

Continuity between
terminals (20)
OK:ContinuityNGCheck the following
connectors:
B-51, B-78, B-80NG
Repair
OK
Check trouble symptoms.
NG
Check the harness wire between the SRS-ECU and earth, and
repair if necessary.
OK
Measure at SRS check harness connector (5).

Disconnect SRS-ECU connector B-51.

Connect SRS check harness connector (3).

Ignition switch: ON

Voltage between terminal (14) and body earth
OK:9 V or moreNGCheck the following
connectors:
B-51, B-78NG
Repair
OK
Check trouble symptoms.
NG
Check the harness wire between the SRS-ECU and ignition switch
IG
1, and repair if necessary.
OK
Replace the SRS-ECU.
SRS check harness
(MB991613)
3
5

SRS – Troubleshooting52B-11
Code No.42 IG1 (B) power circuit systemProbable cause
This diagnosis code is output if the voltage between the IG1 (B) terminal and the
earth is lower than the specified value for a continuous period of 5 seconds or more.
However, if the vehicle condition returns to normal, diagnosis code No.42 will be
automatically erased, and the SRS warning lamp will switch off.
Malfunction of wiring harnesses or connectors
NG
Check the harness wire between the SRS-ECU and ignition switch
IG
1, and repair if necessary.
OK
Check trouble symptoms.
OK
Replace the SRS-ECU.
OK
Measure at SRS check harness connector (5).

Disconnect SRS-ECU connector B-51.

Connect SRS check harness connector (3).

Ignition switch: ON

Voltage between terminal (13) and body earth
OK:9 V or moreNGCheck the following
connectors:
B-51, B-78NG
Repair
NG
Check the harness wire between the SRS-ECU and earth, and
repair if necessary.
OK
Check trouble symptoms.
Measure at SRS check harness
connector (5).

Disconnect SRS-ECU
connector B-51.

Connect SRS check
harness connector (3).

Continuity between
terminals (20)
OK:ContinuityNGCheck the following
connectors:
B-51, B-78, B-80NG
RepairSRS check harness
(MB991613)
3
5