MITSUBISHI MIRAGE 2017 6.G Owners Manual

Fuses 9-24 Vehicle care and maintenance
9
 The table above shows the main equip- ment corresponding to each fuse.
* : Fusible link
Engine compartment fuse location table No.
Sym- bol
Electrical system
Capac-ity
SBF1 Radiator fan motor 40 A
*
SBF2
Anti-lock braking
system
30 A
*
SBF3 Ignition switch 40 A
*
SBF4
Power window
control
40 A
*
Type A
BF1 DC-DC (P/T) 30 A BF2 DC-DC (AUDIO) 30 A F1
Headlight (low beam) (left)
Halo- gen
10 A
Dis- charge
20 A
F2
Headlight (low beam) (right)
Halo- gen
10 A
Dis- charge
20 A
F3
Headlight (high beam) (left)
10 A
F4
Headlight (high beam) (right)
10 A
F5 Horn 10 A F6 Front fog lights 15 A F7
Daytime running
lights
10 A
F8 — — —
Battery current
sensor
7.5 A
F11 — — —
Sym- bol
Electrical system
Capac-ity
F12
Stop lights (Brake
lights)
15 A
F13 Ignition coil 7.5 A F14 Engine control 7.5 AF15 Alternator 7.5 A F16
Hazard warning
flasher
10 A
F17
Automatic trans-
axle
15 A
F18 Air conditioning 10 A F19 ETV 15 A F20 Starter 7.5 A F21 CVT oil/pump 15 A F22 Fuel pump 15 A F23 Engine 20 A F24
Automatic trans-
axle
7.5 A
#1 — Spare fuse 20 A #2 — Spare fuse 30 ANo.
Sym- bol
Electrical system
Capac-ity
BK0235100US.book 24 ページ ２０１５年１１月２０日　金曜日　午後３時１２分

Fuses
Vehicle care and maintenance 9-25
9
 Some fuses may not be installed on your vehicle, depending on
the vehicle model
or specifications.  The table above show
s the main equip-
ment corresponding to each fuse.
* : Fusible link  Some fuses may not be installed on your vehicle, depending on
the vehicle model
or specifications.  The table above show
s the main equip-
ment corresponding to each fuse.
The fuse block does not contain spare 7.5 A, 10 A or 15 A fuses. If one of these fusesburns out, substitute with the following fuse. 7.5 A: Outside rearview mirrors 10 A: Option15 A: Cigarette lighter When using a substitute fuse, replace with a fuse of the correct capacity as soon as possi-ble.
N00954900131
1. Before replacing a fuse, always turn off the electrical item concerned to the fuse and turn the ignition switch to the “OFF”position or put th
e operation mode in
OFF.
2. There is a fuse remover (A) in the engine compartment fuse block. 3. Clamp it on the fuse you wish to remove, and pull the fuse straight out from the fuse block.
No.
Sym- bol
Electrical system
Capac-ity
SBF1 PTC heater 40 A
*
SBF2 PTC heater 40 A
*
SBF3 PTC heater 40 A
*
Type B
Identification of fuse Capacity
Color
7.5 A Brown 10 A Red 15 A Blue 20 A Yellow 30 A
Green (fuse type) /Pink (fusible
link type)
40 A Green (fusible link type)
BK0235100US.book 25 ページ ２０１５年１１月２０日　金曜日　午後３時１２分

Replacement of light bulbs 9-26 Vehicle care and maintenance
9
4. Use the fuse location diagrams and the matching tables, to check the fuse that isrelated to the problem. If the fuse is not blown, something else
must be causing
the problem. Have the system inspectedby your authorized Mitsubishi Motors dealer or a repair fa
cility of your choice.
5. Insert a new fuse
of the same capacity
securely into the appropriate slot.
N00942901362
Before replacing the bulb, be sure the light is off. Do not touch the glass part of the new bulb with your bare fingers; the oil from yourskin will stay on the
glass and dim or destroy
the bulb when it gets hot.
B- Fuse is OK C- Blown fuseCAUTION Never use a fuse with a capacity greater than the one listed or any s
ubstitute, such as wire,
foil etc. This would
cause the circuit wiring
to heat up and could cause a fire.
 If the replacement fuse blows again after a short time, have the electrical systemchecked by an authorized Mitsubishi Motorsdealer or a repair fa
cility of your choice to
find and correct the cause.
Replacement of light bulbs
CAUTION Bulbs are extremely hot immediately after being turned off.When replacing the bulb, wait for it to cool sufficiently before
touching it. You could
otherwise be burned. Handle halogen light bul
b with care. The gas
inside halogen light
bulb is highly pressur-
ized, so dropping, knocki
ng, or scratching a
halogen light bulb can
cause it to shatter.
CAUTION
Never hold the halogen
light bulb with a bare
hand, dirty glove, etc.The oil from your hand could cause the bulbto break the next ti
me the headlights are
used. If the glass surface is dirty, clean it withalcohol and let it dry completely before installing the bulb.CAUTION Do not install commercially available LED- type bulbs. Commercially availa
ble LED-type bulbs
could adversely affect the operation of thevehicle, such as by preventing the lights and other vehicle equi
pment from operating
properly.CAUTION
BK0235100US.book 26 ページ ２０１５年１１月２０日　金曜日　午後３時１２分

Replacement of light bulbs
Vehicle care and maintenance 9-27
9
N00943000132
The bulb should only be replaced with a new bulb with the same rating and type. The typeand rating are listed on the base of the bulb.
N00950302030
NOTE
 If you are unsure of how to carry out the work as required, it is recommended thatthese procedures be carried out by an autho-rized Mitsubishi Motors dealer or a repair facility of your choice.  Be careful not to scratch the vehicle body when removing a light and lens.  When it rains, or wh
en the vehicle has been
washed, the inside of the lens sometimes becomes temporarily foggy. This is the samephenomenon as when window glass mists up on a humid day, and does not indicate a func- tional problem.When the light is switched on, the heat will remove the fog. However, if water gathers inside the light, please
have it checked by an
authorized Mitsubishi Motors dealer or a repair facility of your choice.
Bulb capacity
Outside Type A: Halogen headlights type Type B: Bi-xenon High intensity discharge
(HID) headlights type
Front Ty p e A Ty p e B
Description
Watt-age
ANSI Tr a d e N o . or Bulb type
1
Front turn signal light
27 W #1156NA
2
Headlight/Day- time running light (if so equipped) (Type A)
60/55 W HB2
Headlight (Type
B)
35 W —
Parking light
Type A
5 W W5W
Type B
——
4
Front side-marker light
5 W W5W
5
Front fog light (if so equipped)
19 W H16
Front fog light/Day- time run- ning light (if so equipped)
Fron t fog light
35 W H8
Day- time run-ning light
13 W P13W
BK0235100US.book 27 ページ ２０１５年１１月２０日　金曜日　午後３時１２分

Replacement of light bulbs 9-28 Vehicle care and maintenance
9
6
Side turn signal light (on fender, if so equipped)
5 W —
Side turn signal light (on outside rearview mirror, if so equipped)
——
WA R N I N G Check with an auth
orized Mitsubishi
Motors dealer or a re
pair facility of your
choice when it is necessary to repair the Bi-xenon HID headlight
or to replace the
bulb.The power circuit, bulb and electrodes generate high voltages that may cause a severe shock.NOTE
 It is not possible to re
pair or replace only the
bulb for the side turn signal light (on fender).Check with an authorized Mitsubishi Motors dealer or a repair fa
cility of your choice
when the light needs to be repaired orreplaced.Description
Wa t t- age
ANSI Tr a d e N o . or Bulb type
 The following lights use an LED instead of the bulb. Check with an authorized Mitsubi-shi Motors dealer or a repair facility of yourchoice when either light
needs to be repaired
or replaced. • Parking light (Type B) • Side turn signal light (on outside rearview mirror)
Item
Wattage
ANSI trade No. or bulb type
1
High-mounted stop light
——
2
License plate light
5 W W5W
3 Back-up light 16 W W16W
NOTE
Rear
4
Rear turn signal light
21 W PY21W
5
Tail and stop light
——
6
Rear side-marker light
——
NOTE
 The following lights use an LED instead of the bulb. Check with an authorized Mitsubi-shi Motors dealer or a repair facility of your choice when either light
needs to be repaired
or replaced. • High-mounted stop light • Tail and stop light • Rear side-marker light
Item
Wattage
ANSI trade No. or bulb type
BK0235100US.book 28 ページ ２０１５年１１月２０日　金曜日　午後３時１２分

Replacement of light bulbs
Vehicle care and maintenance 9-29
9
N00950400646
N00901801199
1. Pull out the connector (A), and then remove the sealing cover (B). 2. Unhook the spring (C), which secures the bulb, and then remove the bulb (D).
3. To install the bulb, perform the removal steps in reverse.
N00943200352
The alignment of the headlights should bechecked by an authorized Mitsubishi Motorsdealer or a repair fa
cility of your choice.
N00917301665
1. For vehicles with Bi-xenon HID head- lights, when replacing the bulb on the left side, remove the cap (A) by turning itcounterclockwise to create enough work space.
Inside
Item
Wattage
1 Cargo room light 5 W 2 Dome light 8 W
Headlights/Daytime running lights
(if so equipped)
headlights type) *- Front of the vehicle
Headlight aim adjustment Front side-marker lights
BK0235100US.book 29 ページ ２０１５年１１月２０日　金曜日　午後３時１２分

Replacement of light bulbs 9-30 Vehicle care and maintenance
9
2. Turn the socket (B) counterclockwise to remove it. 3. Pull the bulb out of the socket. 4. To install the bulb, perform the removal steps in reverse.
N00943401465
1. Turn the socket (A
) counterclockwise to
remove it.
2. Remove the bulb from the socket by turn- ing it counterclockwis
e while pressing in.
3. To install the bulb, perform the removal steps in reverse.
*- Front of the vehicle
Front turn signal lights Type A: Halogen headlights type Type B: Bi-xenon High
intensity discharge
(HID) headlights type
*- Front of the vehicleType A Type B
BK0235100US.book 30 ページ ２０１５年１１月２０日　金曜日　午後３時１２分

Replacement of light bulbs
Vehicle care and maintenance 9-31
9
N00917301678
1. Turn the socket (A
) counterclockwise to
remove it. 2. Pull the bulb out of the socket. 3. To install the bulb, perform the removal steps in reverse.
N00943601890
1. To create enough work space, turn thesteering wheel all the way in the direction opposite to the side you wish to replace. 2. Remove the clips/bolts (A) to turn up thecover (B).
3. While pressing the tab, pull out the con- nector.
Parking lights (Halogen head- lights type) *- Front of the vehicle
Front fog lights
(if so equipped)
/
Front fog lights and Daytime running lights
(if so equipped)
Type 1- Fog light type Type 2- Fog light
and Daytime running
light type
C- Fog light bulbD- Daytime running light bulbTy p e 1 Ty p e 2
BK0235100US.book 31 ページ ２０１５年１１月２０日　金曜日　午後３時１２分

Replacement of light bulbs 9-32 Vehicle care and maintenance
9
4. Turn the bulb counterclockwise to remove it. 5. To install the bulb, perform the removal steps in reverse.
N00943701569
1. Open the liftgate.(Refer to “Liftgate” on page 5-27.) 2. Remove the screws (A) that hold the lightunit. 3. Move the light unit toward the rear of the vehicle to unfix the notch (B) and pin (C).
4. Turn the socket counterclockwise to remove it. 5. Remove the bulb from the socket as fol- lows.
NOTE
 When refitting each of the clips, first insert part (E) of the clip into the hole and thenpress part (F) into it.Ty p e 1 Ty p e 2
Rear combination lights
D- Back-up light E- Rear turn signal lightF- Rear side-marker
light, and tail and
stop light (LED) - Do not touch the socket because repl
acing this light is
carried out by an authorized Mitsubishi Motors dealer or a repair facility of your choice.NOTE
 The rear side-marker li
ght, and tail and stop
light use an LED instead of the bulb. Check with an authorized Mitsubishi Motors dealer or a repair fa
cility of your choice
when the light needs to be repaired or replaced.
BK0235100US.book 32 ページ ２０１５年１１月２０日　金曜日　午後３時１２分

Vehicle care precautions
Vehicle care and maintenance 9-33
9
• Back-up light bulb
Pull the bulb out.
• Rear turn signal light bulb
Turn the bulb counterclockwise while pressing in.
6. To install the bulb, perform the removal steps in reverse.
N00944001426
1. Push the light unit (A) toward the left sideof the vehicle to remove it. 2. Turn the socket (B) counterclockwise to remove it, and then pull the bulb out fromthe socket.
3. To install the bulb, perform the removal steps in reverse.
N00945100166
In order to maintain the value of your vehicle,perform regular mainte
nance using the proper
materials and procedures
. Be sure to use only
those materials and proc
edures that meet your
local environmental pollution control regula- tions. Choose the materials you will use care- fully, to be sure that they do not containcorrosives. If you are
not sure, contact an
authorized Mitsubishi Motors dealer for help in choosing these materials.
NOTE
 When mounting the lamp unit, align the notch (G) and pin (H) on the lamp unit withthe clip (I) and hole (J) in the body.Back-up light bulb Rear
turn signal light
bulb
License plate lights
NOTE
 When installing the light unit, first insert the tab (C) into the hole on the body, and then push on the light unit to fit it into place.
Vehicle care precautions
BK0235100US.book 33 ページ ２０１５年１１月２０日　金曜日　午後３時１２分