spark MITSUBISHI MONTERO 1991 Workshop Manual

Vacuum leak Repair vacuum leak
Improper float bowl fuel Reset float
level adjustment, see FUEL
Clogged air bleed or idle Clean carburetor
passages passages, see FUEL
Clogged or worn air cleaner Replace air filter
filter
Faulty choke vacuum Replace diaphragm,
diaphragm see ENGINE PERFORMANCE
Exhaust manifold heat valve Replace heat valve
inoperative
Improper distributor spark Check distributor
advance operation
Leaking valves or valve Check and repair
components valvetrain
Improper carburetor Remove and remount
mounting carburetor
Excessive play in Replace distributor
distributor shaft
Loose or corroded wiring Repair or replace as
connections required









\









\









\









\









\









\









\







Engine Surges Improper PCV valve airflow Replace PCV valve
Vacuum leaks Repair vacuum leaks
Clogged air bleeds Remove restriction
EGR valve malfunction Replace EGR valve
Restricted air cleaner Replace air filter
filter
Cracked or broken vacuum Replace vacuum hoses
hoses
Cracked or broken ignition Replace ignition
wires wires
Vacuum advance malfunction Check unit and
replace as necessary
Defective or fouled spark Replace spark plugs
plugs









\









\









\









\









\









\









\







Ping or Spark Incorrect ignition timing Reset ignition timing
Knock see ENGINE PERFORMANCE
Distributor centrifugal or Check operation and
vacuum advance malfunction replace as necessary
Carburetor setting too lean Readjust mixture

setting, see ENGINE
PERFORMANCE
Vacuum leak Eliminate vacuum leak
EGR valve malfunction Replace EGR valve









\









\









\









\









\









\









\







Poor Gasoline Cracked or broken vacuum Replace vacuum hoses
Mileage hoses
Vacuum leaks Repair vacuum leaks
Defective ignition wires Replace wires
Incorrect choke setting Readjust setting, see
ENGINE PERFORMANCE
Defective vacuum advance Replace vacuum advance
Defective spark plugs Replace spark plugs
Binding carburetor power Eliminate binding
piston
Dirt in carburetor jets Clean and/or replace
jets
Incorrect float adjustment Readjust float
setting, see FUEL
Defective power valve Replace power valve,
see ENGINE PERFORMANCE
Incorrect idle speed Readjust idle speed









\









\









\









\









\









\









\







Engine Stalls Improper float level Readjust float level
Leaking needle valve and Replace needle valve
seat and seat
Vacuum leaks Eliminate vacuum
leaks









\









\









\









\









\









\









\







VACUUM PUMP - DIESEL TROUBLE SHOOTING
NOTE: This is GENERAL information. This article is not intended
to be specific to any unique situation or individual vehicle
configuration. The purpose of this Trouble Shooting
information is to provide a list of common causes to
problem symptoms. For model-specific Trouble Shooting,
refer to SUBJECT, DIAGNOSTIC, or TESTING articles available
in the section(s) you are accessing.
NOTE: Diesel engines mechanical diagnosis is the same as gasoline
engines for items such as noisy valves, bearings, pistons,
etc. The following trouble shooting covers only items
pertaining to diesel engines.
VACUUM PUMP (DIESEL) TROUBLE SHOOTING CHART









\









\









\









\









\









\









\







CONDITION POSSIBLE CAUSE CORRECTION








\









\









\









\









\









\









\

\003
WAVEFO RM S - IN JE C TO R P A TTE R N T U TO RIA L

1991 M it s u bis h i M onte ro
GENERAL INFORMATION
Waveforms - Injector Pattern Tutorial
* PLEASE READ THIS FIRST *
NOTE: This article is intended for general information purposes
only. This information may not apply to all makes and models.
PURPOSE OF THIS ARTICLE
Learning how to interpret injector drive patterns from a Lab
Scope can be like learning ignition patterns all over again. This
article exists to ease you into becoming a skilled injector pattern
interpreter.
You will learn:
* How a DVOM and noid light fall short of a lab scope.
* The two types of injector driver circuits, voltage controlled
& current controlled.
* The two ways injector circuits can be wired, constant
ground/switched power & constant power/switched ground.
* The two different pattern types you can use to diagnose with,
voltage & current.
* All the valuable details injector patterns can reveal.
SCOPE OF THIS ARTICLE
This is NOT a manufacturer specific article. All different
types of systems are covered here, regardless of the specific
year/make/model/engine.
The reason for such broad coverage is because there are only
a few basic ways to operate a solenoid-type injector. By understanding
the fundamental principles, you will understand all the major points
of injector patterns you encounter. Of course there are minor
differences in each specific system, but that is where a waveform
library helps out.
If this is confusing, consider a secondary ignition pattern.
Even though there are many different implementations, each still has
a primary voltage turn-on, firing line, spark line, etc.
If specific waveforms are available in On Demand for the
engine and vehicle you are working on, you will find them in the
Engine Performance section under the Engine Performance category.
IS A LAB SCOPE NECESSARY?
INTRODUCTION
You probably have several tools at your disposal to diagnose
injector circuits. But you might have questioned "Is a lab scope
necessary to do a thorough job, or will a set of noid lights and a
multifunction DVOM do just as well?"
In the following text, we are going to look at what noid
lights and DVOMs do best, do not do very well, and when they can
mislead you. As you might suspect, the lab scope, with its ability to
look inside an active circuit, comes to the rescue by answering for
the deficiencies of these other tools.
OVERVIEW OF NOID LIGHT