battery MITSUBISHI MONTERO 1991 Workshop Manual
Page 669 of 1333
15 x 6JJ (Steel) ........................... P225/75 R15
1989-1996
15 x 6JJ (Steel) ........................... P225/75 R15
15 x 6JJ (Steel or Aluminum) ............... P235/75 R15
15 X 7JJ (Aluminum) ........................ 31-10.50R15
\
\
\
\
\
\
TIRE INFLATION SPECIFICATIONS TABLE\
\
\
\
\
\
Application Pressure
psi (kg/cm )
1983-88
Front ( 1) ..................................... 26 (1.8)
Rear .......................................... 34 (2.3)
Rear ...................................... ( 2) 26 (1.8)
1989-91
Front ( 1) ..................................... 26 (1.8)
Rear .......................................... 35 (2.4)
Rear ...................................... ( 2) 26 (1.8)
1992-96
P235/75R15
Front ........................................ 26 (1.8)
Rear ......................................... 35 (2.4)
31-10.50R15
Front ........................................ 29 (2.1)
Rear ......................................... 40 (2.8)
( 1) - No chain clearance.
( 2) - Inflation pressure for better ride comfort when
driving with no cargo.
\
\
\
\
\
\
WHEEL TIGHTENING
WHEEL TIGHTENING SPECIFICATIONS TABLE\
\
\
\
\
\
Application Ft. Lbs. (N.m.)
1983 ....................................... 50-57 (70-80)
1984-96 .................................. 72-87 (100-120)
\
\
\
\
\
\
BATTERY SPECIFICATIONS
CAUTION: When battery is disconnected, vehicles equipped with
computers may lose memory data. When battery power is
restored, driveability problems may exist on some vehicles.
These vehicles may require a relearn procedure. See
COMPUTER RELEARN PROCEDURES article in the GENERAL
INFORMATION Section.
Battery is maintenance-free and does not normally require
additional water. However, under severe conditions it is advisable to
check battery fluid periodically. Use only distilled water to fill
battery cell should it become necessary to add water. Charge condition
can be checked by a visual test indicator on top of battery.
BATTERY REPLACEMENT SPECIFICATIONS TABLE
\
\
\
\
\
\
Application BCI Group Number
Page 670 of 1333
2.6L Engine ........................................... 45
2.6L Optional ......................................... 45
3.0L V6 ........................................... (1) 24
3.5L V6 ........................................... ( 1) 24
( 1) - Check hood clearance on 1986 and newer models.
\
\
\
\
\
\
CAUTIONS & WARNINGS
SUPPLEMENTAL RESTRAINT SYSTEM (SRS) AIR BAG SYSTEM
NOTE: See the AIR BAG RESTRAINT SYSTEM article in the
ACCESSORIES/SAFETY EQUIPMENT Section.
The SRS has no user-servicable parts. Always have servicing
done by an authorized dealer.
When performing maintenance on air bag equipped vehicles
always observe proper safety precautions.
WARNING: To avoid injury from accidental air bag deployment, read and
carefully follow all warnings and service precautions. See
appropriate AIR BAG RESTRAINT SYSTEM article in the
ACCESSORIES/SAFETY EQUIPMENT section.
CAUTION: Disconnect negative battery cable before servicing any air
bag system, steering column or passenger side dash
component. After any repair, turn ignition key to the ON
position from passenger's side of vehicle in case of
accidental air bag inflation
ANTI-LOCK BRAKE SYSTEM (ABS)
CAUTION: Never mix different diameter tires. On loose or uneven
surfaces, the ABS system may require longer stopping
distances than conventional brake systems. Exercise caution
when removing mud or snow from the wheels so as not to
damage the ABS wiring or speed sensors.
BATTERY WARNING
WARNING: When battery is disconnected, vehicles equipped with
computers may lose memory data. When battery power is
restored, driveability problems may exist on some vehicles.
These vehicles may require a relearn procedure. See
appropriate COMPUTER RELEARN PROCEDURES article in the
GENERAL INFORMATION section below.
REPLACING BLOWN FUSES
Before replacing a blown fuse, remove ignition key, turn off
all lights and accessories to avoid damaging the electrical system. Be
sure to use fuse with the correct indicated amperage rating. The use
of an incorrect amperage rating fuse may result in a dangerous
electrical system overload.
BRAKE PAD WEAR INDICATOR
Indicator will cause a squealing or scraping noise, warning
that brake pads need replacement.
Page 672 of 1333
WARNING: Keep hands away from radiator fan. Fan is controlled by a
thermostatic switch which may come on or run for up to
15 minutes even after engine is turned off.
WARRANTY INFORMATION
CAUTION: Always refer to customer's copy of warranty information for
specific model application and/or coverage limitations.
NEW VEHICLE LIMITED WARRANTY
Covers all manufacturer-installed parts and components for
any repairs, replacements or adjustments needed to correct defects in
materials or workmanship under normal use and maintenance for 36
months or 36,000 miles, whichever comes first, from date of delivery
to the first retail buyer or first date of use.
POWERTRAIN LIMITED WARRANTY
Upon expiration of New Vehicle Limited Warranty, this
warranty covers powertrain against defects in materials or workmanship
up to a maximum of 36 months or 50,000 miles, whichever occurs first.
On 1991-96 models, warranty period is extended to 5 years or 60,000
miles, whichever occurs first. See copy of warranty for specific
components covered.
BATTERY WARRANTY
Covers replacement of original battery for 12 months or 12,
000 miles, whichever occurs first.
AIR CONDITIONER WARRANTY
Covers manufacturer's air conditioners for 36 months or 36,
000 miles, whichever occurs first. Air conditioner refrigerant charge
is covered for the first 12 months or 12,000 miles, whichever occurs
first. On 1992-96 models, refrigerant is covered only as part of a
warranty repair.
ANTI-CORROSION PERFORATION LIMITED WARRANTY
Covers any body sheet metal panel found to have developed
perforation (rust-through) due to corrosion for 5 years regardless of
mileage. Outer panel coverage extends to 7 years or 100,000 miles,
whichever occurs first, on 1992-96 models.
EMISSION SYSTEM DEFECT WARRANTY (EXCEPT CALIFORNIA)
Warrants that the vehicle was designed, built and equipped to
conform at the time of sale with all applicable U.S. emission
standards. Covers any repairs needed to correct defects in materials
or workmanship which would cause the vehicle not to meet these
standards for 5 years or 50,000 miles, whichever occurs first.
EMISSION SYSTEM PERFORMANCE WARRANTY (EXCEPT CALIFORNIA)
Covers all repairs, adjustments, or replacements if vehicle
has been maintained in accordance with the prescribed scheduled
maintenance instructions and fails to conform to applicable emission
standards and such failure results or will result in the vehicle owner
having to bear any penalty or other sanctions under local, state or
Page 689 of 1333
FUEL SYSTEM PRESSURE RELEASE
WARNING: ALWAYS relieve fuel pressure before disconnecting any fuel
injection-related component. DO NOT allow fuel to contact
engine or electrical components.
1) On Colt and Mirage, remove rear seat cushion. On all
models, disconnect fuel pump harness connector at fuel tank.
2) Start engine. Let engine run until it stops. Turn ignition
off. Disconnect negative battery terminal. Connect fuel pump harness
connector.
FUEL PUMP
Removal & Installation
1) Fuel pump assembly is located inside fuel tank. Release
fuel pressure from system. See FUEL SYSTEM PRESSURE RELEASE. Raise
vehicle on hoist. Drain fuel into suitable container. Disconnect
electrical connectors and fuel hoses at fuel tank.
2) Remove fuel filler hose from fuel tank. Remove nuts
securing fuel tank. Remove fuel tank from vehicle and remove fuel pump
assembly. To install, reverse removal procedure. Tighten nuts to
specification. See TORQUE SPECIFICATION table.
FUEL RAILS & INJECTORS (PFI)
Use a rag to cover fuel hose connection before disconnecting
high pressure fuel hose at fuel rail. Some residual fuel pressure may
still be in system.
Removal (Except Pickup & Ram-50 2.4L)
1) On all models, relieve fuel pressure. See
FUEL SYSTEM PRESSURE RELEASE . Disconnect negative battery cable. On
Montero, Pickup, Ram-50, Stealth and 3000GT 3.0L, disconnect air
intake plenum. On Eclipse, disconnect PCV valve hose.
2) On Colt Vista, disconnect coolant temperature sensor
connector, idle speed control servo connector and brake booster vacuum
hose. On all models, disconnect high pressure fuel hose at fuel rail.
3) Disconnect fuel return hose. Disconnect vacuum hoses. On
Eclipse, Colt and Colt 200, disconnect throttle cable clamp. Remove
center cover. On all models, disconnect injector electrical
connectors. Remove fuel rail bolts and lift fuel rail and injectors
from engine.
Installation
To install, reverse removal procedure. Tighten bolts to
specifications. See TORQUE SPECIFICATIONS table.
Removal (Pickup & Ram-50 2.4L)
1) Relieve fuel pressure. See FUEL SYSTEM PRESSURE RELEASE.
Disconnect negative battery cable. Drain coolant. On all models,
disconnect air intake hose. Disconnect breather hose (if applicable)
and vacuum hoses.
2) Disconnect coolant lines as necessary for clearance.
Disconnect injector electrical connectors. Position all lines, hoses
and electrical connectors out of way. Disconnect throttle and/or
kickdown cables. Remove throttle body assembly and position it out of
the way.
3) Disconnect high pressure fuel hose at fuel rail.
Disconnect fuel return line and vacuum line connection at fuel rail.
Remove fuel rail bolts and lift fuel rail and injectors from engine.
Page 691 of 1333
NOTE: Removal of turbocharger exhaust housing and water pipes at
turbocharger is not necessary when removing turbocharger
assembly. Stealth and 3000GT models have 2 (front and rear)
turbochargers.
Removal (Eclipse & Galant)
1) Disconnect negative battery cable. Drain engine coolant
and oil. On models with A/C, remove condenser fan motor assembly. On
all models, remove oxygen sensor. Remove oil dipstick guide and "O"
ring. See Figs. 8 and 9.
Fig. 8: Removing Turbocharger (Eclipse & Galant 2.0L)
Courtesy of Mitsubishi Motor Sales of America.
Fig. 9: Exploded View of Turbocharger Assembly (Eclipse & Galant
2.0L Shown; Stealth & 3000GT Similar)
Page 692 of 1333
Courtesy of Mitsubishi Motor Sales of America.
2) Disconnect air intake hose and vacuum hoses. Remove air
hose and air outlet housing. Remove heat protectors. Disconnect
exhaust pipe. Remove power steering oil pump and bracket. Remove
engine hanger bracket. Disconnect oil inlet pipe.
3) Disconnect coolant hose and tubes. Remove nuts and bolts
securing exhaust manifold. Remove exhaust manifold and gaskets.
Disconnect oil return pipe. Remove turbocharger assembly.
Removal (Stealth & 3000GT Front)
1) Disconnect negative battery cable. Drain engine oil and
coolant. Remove radiator. Disconnect exhaust pipe. Remove air intake
hose, air hoses and air pipe. Remove alternator and belt. Remove oil
dipstick guide.
2) Remove heat protector. Disconnect oxygen sensor electrical
connector. Remove oil return pipe. Remove turbocharger support bracket
and remove turbocharger from exhaust manifold. See Fig. 10.
Fig. 10: Removing Front Turbocharger (Stealth & 3000GT)
Courtesy of Mitsubishi Motor Sales of America.
Removal (Stealth & 3000GT Rear)
1) Disconnect battery cables and remove battery. Drain engine
oil and coolant. Remove accelerator cable. Remove air hose, air pipe
and heat protectors. Disconnect clutch booster vacuum hose. Remove air
Page 696 of 1333
SC HED ULE D S ER VIC ES
1991 Mitsubishi Montero
1987-95 MAINTENANCE
Mitsubishi Maintenance & Service Intervals
Montero
* PLEASE READ THIS FIRST *
NOTE: All SERVICE SCHEDULES are listed for normal service
vehicles. If vehicle is operated under severe service
conditions, see
SEVERE SERVICE REQUIREMENTS (PERFORM W/SERVICE SCHEDULES)
for items requiring additional maintenance.
NOTE: This article contains scheduled maintenance service
information. Fluid types and capacities listed with each
service in this article are only those necessary to perform
that scheduled service. For specifications pertaining to
fluid capacities for the entire vehicle, fuse and circuit
breaker identification, wheel and tire size, battery type,
warranty information, or model identification refer to the
MAINTENANCE INFORMATION article in this section.
CAUTIONS & WARNINGS
SUPPLEMENTAL RESTRAINT SYSTEM (AIR BAG)
NOTE: See the AIR BAG RESTRAINT SYSTEM article in the
ACCESSORIES/SAFETY EQUIPMENT Section.
Modifications or improper maintenance, including incorrect
removal and installation of the Supplemental Restraint System (SRS),
can adversely affect system performance. DO NOT cover, obstruct or
change the steering wheel horn pad in any way, as such action could
cause improper function of the system. Use only plain water when
cleaning the horn pad. Solvents or cleaners could adversely affect the
air bag cover and cause improper deployment of the system.
WARNING: To avoid injury from accidental air bag deployment, read and
carefully follow all warnings and service precautions. See
appropriate AIR BAG RESTRAINT SYSTEM article in the
ACCESSORIES/SAFETY EQUIPMENT section.
CAUTION: Disconnect negative battery cable before servicing any air
bag system, steering column or passenger side dash
component. After any repair, turn ignition key to the ON
position from passenger's side of vehicle in case of
accidental air bag inflation
AIR CONDITIONING SERVICING
WARNING: R-134a service equipment or vehicle A/C systems SHOULD NOT
be pressure tested or leak tested with compressed air. Some
mixtures of air/R134a have shown to be combustible at
elevated pressures. These mixtures are dangerous and may
cause fire and/or explosions. See the appropriate
A/C SYSTEM GENERAL SERVICING article in the AIR CONDITIONING
& HEAT section.
Page 697 of 1333
WARNING: Avoid breathing R-134a refrigerant and PAG lubricant vapors,
exposure may irritate eyes, nose and throat. To remove
R-134a from system use R-134a recycling equipment that meets
SAE J2210 specifications. If accidental system discharge
occurs, ventilate work area before resuming service.
ANTI-LOCK BRAKE SYSTEM
The anti-lock brake system contains electronic equipment that
can be susceptible to interference caused by improperly installed or
high output radio transmitting equipment. Since this interference
could cause the possible loss of the anti-lock braking capability,
such equipment should be installed by qualified professionals.
On models equipped with anti-lock brake systems, ALWAYS
observe the following cautions:
* DO NOT attempt to bleed hydraulic system without first
referring to the appropriate ANTI-LOCK BRAKE SYSTEM article
in the BRAKES Section.
* DO NOT mix tire sizes. As long as tires remain close to the
original diameter, increasing the width is acceptable.
Rolling diameter must be identical for all 4 tires. Some
manufacturers recommend tires of the same brand, style and
type. Failure to follow this precaution may cause inaccurate
wheel speed readings.
* Use ONLY recommended brake fluids. DO NOT use silicone brake
fluids in an ABS-equipped vehicle.
REPLACING BLOWN FUSES
Before replacing a blown fuse, remove ignition key, turn off
all lights and accessories to avoid damaging the electrical system. Be
sure to use fuse with the correct indicated amperage rating. The use
of an incorrect amperage rating fuse may result in a dangerous
electrical system overload.
BATTERY WARNING
WARNING: When battery is disconnected, vehicles equipped with
computers may lose memory data. When battery power is
restored, driveability problems may exist on some vehicles.
These vehicles may require a relearn procedure. See
appropriate COMPUTER RELEARN PROCEDURES article in the
GENERAL INFORMATION section below.
BRAKE FLUID
For vehicles equipped with a traction control system, idle
engine while pouring brake fluid into reservoir.
CATALYTIC CONVERTER
Continued operation of vehicle with a severe malfunction
could cause converter to overheat, resulting in possible damage to
converter and vehicle.
ELECTROSTATIC DISCHARGE SENSITIVE (ESD) PARTS
WARNING: Many solid state electrical components can be damaged by
static electricity (ESD). Some will display a warning label,
but many will not. Discharge personal static electricity by
Page 734 of 1333
\003
C - S PEC IF IC ATIO NS
1991 M it s u bis h i M onte ro
1991 ENGINE PERFORMANCE
Service & Adjustment Specifications
Chrysler Motors: Colt, Colt 200, Colt Vista,
Ram-50, Stealth, Summit
Mitsubishi: Eclipse, Galant, Mirage, Montero,
Pickup, 3000GT
INTRODUCTION
Use this article to quickly find specifications related to
servicing and on-vehicle adjustments. This is a quick reference
article for when you are familiar with an adjustment procedure and
only need a specification.
CAPACITIES
BATTERY SPECIFICATIONS \
\
\
\
Application Amp. Hr. Rating
Colt, Mirage & Summit
Type 1 ............................... 48
Type 2 ............................... 36
Colt Vista ............................. 36
Colt 200 ............................... 52
Eclipse ................................ 50
Galant ................................. 40
Montero ................................ 52
Pickup
2.4L ................................. 36
3.0L ................................. 52
Ram-50
2.4L ................................. 36
3.0L
Standard ........................... 52
Optional ........................... 55
Stealth & 3000GT ....................... 52
\
\
\
\
FLUID CAPACITIES \
\
\
\
\
\
\
Application Quantity
Automatic Transaxle (Dexron-II)
Colt, Colt 200, Colt Vista, Galant & Mirage ...... 6.4 Qts. (6.1L)\
Galant (AWD) ..................................... 6.8 Qts. (6.5L\
)
Eclipse
Except Turbo ................................... 6.4 Qts. (6.1L)\
Turbo .......................................... 7.4 Qts. (7.0L)\
Stealth & 3000GT ................................. 7.9 Qts. (7.5L)\
Summit ........................................... 6.1 Qts. (5.8L)\
Automatic Transmission (Dexron-II)
Montero .......................................... 7.6 Qts. (7.2L)\
Pickup & Ram-50 .................................. 7.4 Qts. (7.0L)\
Cooling System (Includes Heater & Reserve Tank)
Colt, Colt 200, Mirage & Summit .................. 5.3 Qts. (5.0L)\
Colt Vista ....................................... 7.4 Qts. (7.0L)\
Eclipse
Page 747 of 1333
STA R TE R
1991 M it s u bis h i M onte ro
ELECTRICAL
Starters
Diamante, Eclipse, Expo/Expo LRV, Galant, Mirage, Montero,
Pickup, Precis, 3000GT
DESCRIPTION
Starter is a conventional 12-volt, 4-pole brush-type motor,
with direct or gear reduction drive. The starter-mounted solenoid
shifts overrunning clutch and pinion into flywheel when starter is
energized.
TROUBLE SHOOTING
NOTE: See the TROUBLE SHOOTING - BASIC PROCEDURES article
in the GENERAL TROUBLE SHOOTING section.
NO LOAD TEST
CAUTION: Perform tests in less than 10 seconds to prevent coil
damage.
1) Install starter in soft-jawed vise. Connect starter in
series with a fully charged 12-volt battery. Connect a 100-amp ammeter
and carbon pile rheostat in series with positive battery post and
starter motor terminal. See Fig. 1.
2) Install voltmeter across starter motor. Adjust carbon pile
rheostat to full resistance. Connect cable from starter motor body to
negative battery terminal. Adjust carbon pile rheostat to proper test
voltage. See STARTER NO LOAD SPECIFICATIONS table.
3) Note that maximum amperage is within specification and
starter rotates smoothly. See STARTER NO LOAD SPECIFICATIONS table.
Fig. 1: Starter No Load Test Connections
Courtesy of Chrysler Motors.
STARTER NO LOAD SPECIFICATIONS