belt MITSUBISHI MONTERO 1998 Owners Manual

Page 1379 of 1501

Water Pump Malfunction Replace Water Pump
Fan Clutch Malfunction Replace Fan Clutch
Retarded Ignition Timing Reset Ignition Timing
Cooling Fan Malfunction Test Cooling Fan/
Circuit
Cooling Fan Motor
Malfunction Test Fan Motor
Cooling Fan Relay
Malfunction Test Fan Relay
Faulty Radiator Cap Replace Radiator Cap
Broken/Slipping Fan Belt Replace Fan Belt
Restricted Exhaust Repair Exhaust System
\
\
\
\
\
\
\

Corrosion Impurities In Coolant Clean/Flush System\
\
\
\
\
\
\

Coolant Leakage Damaged hose Replace Hose
Leaky Water Pump Replace Water Pump
Damaged Radiator Seam Replace/Repair Radiator
Leaky Thermostat Cover Replace Thermostat
Cover
Cylinder Head Problem Check Head/Head Gasket
Leaky Freeze Plugs Replace Freeze Plugs
\
\
\
\
\
\
\

Recovery System Inoperative
Loose and/or Defective
Radiator Cap Replace Radiator Cap
Overflow Tube Clogged
and/or Leaking Repair Tube
Recovery Bottle Vent
Restricted Clean Vent
\
\
\
\
\
\
\

No Heater Core Flow
Collapsed Heater Hose Replace Heater Hose
Plugged Heater Core Clean/Replace Heater
Core
Faulty Heater Valve Replace Heater Valve
\
\
\
\
\
\
\

GASOLINE ENGINE - MECHANICAL TROUBLE SHOOTING
NOTE: This is GENERAL information. This article is not intended
to be specific to any unique situation or individual vehicle
configuration. The purpose of this Trouble Shooting
information is to provide a list of common causes to
problem symptoms. For model-specific Trouble Shooting,
refer to SUBJECT, DIAGNOSTIC, or TESTING articles available

Page 1383 of 1501

ENGINES\
\
\
\
\
\
\

High Oil Improper grade of oil Replace with proper oil
Pressure Oil pressure relief valve Eliminate binding
stuck closed
Oil pressure sender or Replace sender or gauge
gauge faulty
\
\
\
\
\
\
\

Noisy Main Inadequate oil supply Check oil delivery to
Bearings main bearings
Excessive main bearing Replace main bearings,
clearance See ENGINES
Excessive crankshaft end Replace crankshaft, See
play ENGINES
Loose flywheel or torque Tighten attaching bolts
converter
Loose or damaged vibration Tighten or replace
damper vibration damper
Crankshaft journals Re-grind crankshaft
out-of-round journals
Excessive belt tension Loosen belt tension
\
\
\
\
\
\
\

Noisy Connecting Excessive bearing clearance Replace bearing, See
Rods or missing bearing ENGINES
Crankshaft rod journal Re-grind crankshaft
out-of-round journal
Misaligned connecting rod Remove rod or cap and
or cap realign
Incorrectly tightened rod Remove and re-tighten
bolts rod bolts
\
\
\
\
\
\
\

Noisy Pistons Excessive piston-to-bore Install larger pistons,
and Rings clearance See ENGINES
Bore tapered or out-of-round Rebore block
Piston ring broken Replace piston rings,
See ENGINES
Piston pin loose or seized Replace piston pin, See
ENGINES
Connecting rods misaligned Realign connecting rods
Ring side clearance too Replace with larger or
loose or tight smaller rings
Carbon build-up on piston Remove carbon
\
\
\
\
\
\
\

Noisy Valve Worn or bent push rods Replace push rods, See
Train ENGINES
Worn rocker arms or bridged Replace push rods, See
pivots ENGINES
Dirt or chips in valve Remove lifters and
lifters remove dirt/chips
Excessive valve lifter Replace valve lifters,
leak-down See ENGINES
Valve lifter face worn Replace valve lifters,
See ENGINES
Broken or cocked valve replace or reposition
springs springs
Too much valve stem-to-guide Replace valve guides,
clearance See ENGINES
Valve bent Replace valve, See
ENGINES
Loose rocker arms Retighten rocker arms,
See ENGINES
Excessive valve seat Reface valve seats, See
run-out ENGINES

Page 1390 of 1501

Incorrect injector pump Check pressure, see
housing pressure FUEL SYSTEMS
\
\
\
\
\
\
\

Engine Cooling system leaks Check cooling system
Overheating and repair leaks
Belt slipping or damaged Check tension and/or
replace belt
Thermostat stuck closed Remove and replace
thermostat, see
ENGINE COOLING
Head gasket leaking Replace head gasket
\
\
\
\
\
\
\

Oil Light on at Low oil pump pressure Check oil pump
Idle operation, see ENGINES
Oil cooler or line Remove restriction
restricted and/or replace cooler
\
\
\
\
\
\
\

Engine Won't Injector pump fuel solenoid Remove and check
Shut Off does not return fuel valve solenoid and replace
to OFF position if needed
\
\
\
\
\
\
\

VACUUM PUMP DIAGNOSIS
Excessive Noise Loose pump-to-drive Tighten screws
assembly screws
Loose tube on pump assembly Tighten tube
Valves not functioning Replace valves
properly
Oil Leakage Loose end plug Tighten end plug
Bad seal crimp Remove and re-crimp
seal
\
\
\
\
\
\
\

FUEL INJECTION TROUBLE SHOOTING
NOTE: This is GENERAL information. This article is not intended
to be specific to any unique situation or individual vehicle
configuration. The purpose of this Trouble Shooting
information is to provide a list of common causes to
problem symptoms. For model-specific Trouble Shooting,
refer to SUBJECT, DIAGNOSTIC, or TESTING articles available
in the section(s) you are accessing.
BASIC FUEL INJECTION TROUBLE SHOOTING CHART
\
\
\
\
\
\
\

CONDITION POSSIBLE CAUSE CORRECTION\
\
\
\
\
\
\

Engine Won't Cold start valve inoperative Test valve and
Start (Cranks circuit
Normally)
Poor connection;vacuum or Check vacuum and
wiring electrical
connections
Contaminated fuel Test fuel for water
or alcohol
Defective fuel pump relay Test relay and
or circuit wiring
Battery too low Charge and test
battery

Page 1392 of 1501

or alcohol
Intermittent ECM ground Test ECM ground
connection for
resistance
Restricted air cleaner Replace air cleaner
Restricted exhaust system Test for exhaust
manifold back
pressure
Poor MAF sensor signal Check leakage
between sensor and
manifold
Poor VSS signal If tester for ALCL
hook-up is available
check that VSS
reading matches
speedometer
\
\
\
\
\
\
\

Ping or Knock on Poor Knock sensor signal Test for shorted or
Acceleration open sensor or
circuit
Poor Baro sensor signal Test for shorted or
open sensor or
circuit
Improper ignition timing See VEHICLE EMISSION
CONTROL LABEL (where
applicable)
Check for engine Low coolant, loose
overheating problems belts or electric
cooling fan
inoperative
\
\
\
\
\
\
\

NOTE: For additional electronic fuel injection trouble shooting
information, see the appropriate article in the ENGINE
PERFORMANCE section (not all vehicles have Computer Engine
Control articles). Information is provided there for
diagnosing fuel system problems on vehicles with electronic
fuel injection.
IGNITION SYSTEM TROUBLE SHOOTING
NOTE: This is GENERAL information. This article is not intended
to be specific to any unique situation or individual vehicle
configuration. The purpose of this Trouble Shooting
information is to provide a list of common causes to
problem symptoms. For model-specific Trouble Shooting,
refer to SUBJECT, DIAGNOSTIC, or TESTING articles available
in the section(s) you are accessing.
Ignition Secondary Trouble Shooting Chart
\
\
\
\
\
\
 
START: Visually inspect Spark Plug Wires, Coil Wires, 

Plug Wire Boots, Rotor, and Distributor Cap for 

signs of damage. 

Page 1402 of 1501

Worn or dirty needle valve Clean carburetor, see
and seat ENGINE PERFORMANCE
Float sticking Readjust or replace
float see the ENGINE
PERFORMANCE section
Incorrect choke adjustment Reset choke adjustment
see ENGINE PERFORMANCE
Defective coil Replace coil
Improper spark plug gap Regap spark plugs
Incorrect ignition timing Reset ignition timing
see ENGINE PERFORMANCE
\
\
\
\
\
\
\

Detonation Over-advanced ignition Reset ignition timing
timing see ENGINE PERFORMANCE
Defective spark plugs Replace spark plugs
Fuel lines clogged Clean fuel lines
EGR system malfunction Check and repair EGR
system
PCV system malfunction Repair PCV system
Vacuum leaks Check and repair
vacuum system
Loose fan belts Tighten or replace
fan belts, see ENGINE
PERFORMANCE
Restricted airflow Remove restriction
Vacuum advance malfunction Check distributor
operation
\
\
\
\
\
\
\

Dieseling Binding carburetor linkage Eliminate binding
Binding throttle linkage Eliminate blinding
Binding choke linkage or Eliminate binding
fast idle cam
Defective idle solenoid Replace idle solenoid
see ENGINE PERFORMANCE
Improper base idle speed Reset idle speed, see
see ENGINE PERFORMANCE
Incorrect ignition timing Reset ignition timing
see ENGINE PERFORMANCE
Incorrect idle mixture Reset idle mixture,
setting see ENGINE PERFORMANCE
\
\
\
\
\
\
\

Faulty Incorrect ignition timing Reset ignition timing
Acceleration see ENGINE PERFORMANCE

Page 1418 of 1501

Worn shaft serrations See STEERING COLUMN
article
\
\
\
\
\
\
\

Growl in Excessive pressure in Restricted hoses, see
Steering Pump hoses POWER STEERING GEAR
article
Scored pressure plates See POWER STEERING GEAR
article
Scored thrust plates or See POWER STEERING GEAR
rotor article
Extreme wear of cam ring See POWER STEERING GEAR
article
\
\
\
\
\
\
\

Rattle in Vanes not installed See POWER STEERING PUMP
Steering Pump article
Vanes sticking in rotor See POWER STEERING PUMP
article
\
\
\
\
\
\
\

Swish noise in Defective flow control See POWER STEERING PUMP
Pump valve article
\
\
\
\
\
\
\

Groan in Air in fluid See POWER STEERING PUMP
Steering Pump article
Poor pressure hose Tighten and check,
connection replace if necessary
\
\
\
\
\
\
\

Squawk When Damper "O" ring on valve See POWER STEERING PUMP
Turning spool cut article
\
\
\
\
\
\
\

Moan or Whine Pump shaft bearing scored Replace bearing and
in Pump fluid
Air in fluid or fluid See POWER STEERING PUMP
level low article
Hose or column grounded Check and replace if
necessary
Cover "O" ring missing See POWER STEERING PUMP
or damaged article
Valve cover baffle See POWER STEERING PUMP
missing or damaged article
Interference of See POWER STEERING PUMP
components in pump article
Loose or poor bracket Correct or replace if
alignment necessary
\
\
\
\
\
\
\

Hissing When Internal leakage in Check valved assembly
Parking steering gear first
\
\
\
\
\
\
\

Chirp in Loose or worn power Adjust or replace if
Steering Pump steering belt necessary
\
\
\
\
\
\
\

Buzzing When Noisy pump See POWER STEERING PUMP
Not Steering article

Page 1420 of 1501

Reaction ring sticking See POWER STEERING GEAR
in housing head article
Steering pump internal See POWER STEERING PUMP
leakage article
Steering gear-to-column See STEERING COLUMN
misalignment article
Lack of lubrication in Service front suspension
linkage
Lack of lubrication in Service front suspension
ball joints
\
\
\
\
\
\
\

Increased Effort High internal pump leakage See POWER STEERING PUMP
When Turning article
Wheel Fast Power steering pump belt Adjust or replace if
Foaming, Milky slipping necessary
Power Steering
Fluid, Low Fluid Low fluid level Check and fill to
Level or Low proper level
Pressure
Engine idle speed to low Adjust to correct
setting
Air in pump fluid system See POWER STEERING PUMP
article
Pump output low See POWER STEERING PUMP
article
Steering gear See POWER STEERING GEAR
malfunctioning article
\
\
\
\
\
\
\

Wheel Surges Low fluid level Check and fill to proper
or Jerks level
Loose fan belt Adjust or replace if
necessary
Insufficient pump See POWER STEERING PUMP
pressure article
Sticky flow control valve See POWER STEERING PUMP
article
Linkage hitting oil pan Replace bent components
at full turn
\
\
\
\
\
\
\

Kick Back or Air in pump fluid system See POWER STEERING PUMP
Free Play article
Worn poppet valve in See POWER STEERING PUMP
steering gear article
Excessive over center See POWER STEERING GEAR
lash article
Thrust bearing out of See POWER STEERING GEAR
adjustment article

Page 1421 of 1501

Free play in pot coupling See POWER STEERING PUMP
article
Steering gear coupling See POWER STEERING PUMP
loose on shaft article
Steering disc mounting Tighten or replace if
bolts loose necessary
Coupling loose on worm Tighten or replace if
shaft necessary
Improper sector shaft See POWER STEERING GEAR
adjustment article
Excessive worm piston See POWER STEERING GEAR
side play article
Damaged valve lever See POWER STEERING GEAR
article
Universal joint loose Tighten or replace if
necessary
Defective rotary valve See POWER STEERING GEAR
article
\
\
\
\
\
\
\

No Power When Sticking flow control See POWER STEERING PUMP
Parking valve article
Insufficient pump See POWER STEERING PUMP
pressure output article
Excessive internal pump See POWER STEERING PUMP
leakage article
Excessive internal gear See POWER STEERING PUMP
leakage article
Flange rubs against gear See STEERING COLUMN
adjust plug article
Loose pump belt Adjust or replace if
necessary
Low fluid level Check and add proper
amount of fluid
Engine idle too low Adjust to correct
setting
Steering gear-to-column See STEERING COLUMN
misaligned article
\
\
\
\
\
\
\

No Power, Left turn reaction seal See POWER STEERING GEAR
Left Turn "O" ring worn article
Left turn reaction seal See POWER STEERING GEAR
damaged/missing article
Cylinder head "O" ring See POWER STEERING PUMP
damaged article
\
\
\
\
\
\
\


Page 1427 of 1501

Mismatched tires See WHEEL ALIGNMENT
Broken or sagging spring See SUSPENSION section
Broken torsion bar See SUSPENSION section
Power steering valve not See STEERING section
centered
Front alignment out of See WHEEL ALIGNMENT
tolerance section
Defective wheel bearing See WHEEL BEARINGS in
SUSPENSION section
Uneven sway bar links See SUSPENSION section
Frame bent Check for frame damage
Steering system bushing See STEERING section
worn
\
\
\
\
\
\
\

Hard Steering Idler arm bushing too tight See STEERING LINKAGE
in STEERING section
Ball joint tight or seized See SUSPENSION section
Steering linkage too tight See STEERING LINKAGE in
STEERING section
Power steering fluid low Add proper amount of
fluid
Power steering drive belt See STEERING section
loose
Power steering pump See STEERING section
defective
Steering gear out of See STEERING section
adjustment
Incorrect wheel alignment See WHEEL ALIGNMENT
Damaged steering gear See STEERING section
Damaged suspension See SUSPENSION section
Bent steering knuckle or See SUSPENSION section
supports
\
\
\
\
\
\
\

Vehicle Strut rod or control arm See SUSPENSION section
"Wanders" bushing worn
Loose or worn wheel See WHEEL BEARINGS in
bearings SUSPENSION section
Improper tire inflation Check tire pressure
Stabilizer bar missing or See SUSPENSION section
defective

Page:   < prev 1-10 ... 51-60 61-70 71-80 81-90 91-100