heating MITSUBISHI MONTERO 1998 Owner's Manual

REFILLING
To prevent air from being trapped in engine block, engine
should be running when refilling cooling system. After system is full,
continue running engine until thermostat is open, then recheck fill
level. Do not overfill system.
TESTING
THERMOSTAT
1) Visually inspect thermostat for corrosion and proper
sealing of valve and seat. If okay, suspend thermostat and thermometer
in a 50/50 mixture of coolant and water. See Fig. 1. Do not allow
thermostat or thermometer to touch bottom of container. Heat water
until thermostat just begins to open.
2) Read temperature on thermometer. This is the initial
opening temperature and should be within specification. Continue
heating water until thermostat is fully open and note temperature.
This is the fully opened temperature. If either reading is not to
specification, replace thermostat.
Fig. 1: Testing Thermostat in Anti-Freeze/Water Solution
PRESSURE TESTING
A pressure tester is used to check both radiator cap and

ON-VEHICLE TESTING
GENERATOR TO BATTERY CONTINUITY TEST
NOTE: Check generator wiring harness connections and drive belt
tension and ensure battery is fully charged before
performing test.
1) Turn ignition off. Disconnect negative battery cable.
Remove output lead from generator terminal "B". See Fig. 1. Install a
100-amp or 130-amp ammeter in series with terminal "B" and
disconnected output lead. Install positive lead of ammeter to terminal
"B" and negative lead to disconnected output wire.
Fig. 1: Identifying Generator Terminals (Typical)
Courtesy of Mitsubishi Motor Sales of America
2) Install positive lead of digital voltmeter to terminal "B"
and negative lead to positive battery terminal. Install a tachometer
and reconnect negative battery cable.
3) Start and operate engine at 2500 RPM. Turn accessories on
and adjust engine speed until ammeter indicates slightly greater than
30 amps, and note voltmeter reading. If voltmeter indicates .3 volt or
less, system is okay.
4) If voltage is greater than .3 volt, check wiring between
generator terminal "B", fusible link and positive battery terminal. If
terminal is not sufficiently tight or if harness is discolored due to
overheating, repair as necessary and retest.

profit organizations. MAP conducted pilot programs in twelve states
before announcing the program nationally in October, 1998. During the
pilots, participating repair shops demonstrated their adherence to the
Pledge and Standards and agreed to follow the UICS in communicating
the results of their inspection to their customers. To put some
"teeth" in the program, an accreditation requirement for shops was
initiated. The requirements are stringent, and a self-policing method
has been incorporated which includes the "mystery shopping" of
outlets.
We welcome you to join us as we continue our outreach... with
your support, both the automotive repair industry and your customers
will reap the benefits. Please visit MAP at our Internet site www.
motorist.org or contact us at:
1444 I Street, NW Suite 700
Washington, DC 20005
Phone (202) 712-9042 Fax (202) 216-9646
January 1999
MAP UNIFORM INSPECTION GENERAL GUIDELINES
OVERVIEW OF SERVICE REQUIREMENTS & SUGGESTIONS
It is MAP policy that all exhaust, brake, steering,
suspension, wheel alignment, drive-line, engine performance and
maintenance, and heating, ventilation and air conditioning, and
electrical services be offered and performed under the standards and
procedures specified in these sections.
Before any service is performed on a vehicle, an inspection
of the appropriate system must be performed. The results of this
inspection must be explained to the customer and documented on an
inspection form. The condition of the vehicle and its components will
indicate what services/part replacements may be "Required" or
"Suggested". In addition, suggestions may be made to satisfy the
requests expressed by the customer.
When a component is suggested or required to be repaired or
replaced, the decision to repair or replace must be made in the
customer's best interest, and at his or her choice given the options
available.
This section lists the various parts and conditions that
indicate a required or suggested service or part replacement.
Although this list is extensive, it is not fully inclusive. In
addition to this list, a technician may make a suggestion. However,
any suggestions must be based on substantial and informed experience,
or the vehicle manufacturer's recommended service interval and must be
documented.
Some conditions indicate that service or part replacement is
required because the part in question is no longer providing the
function for which it is intended, does not meet a vehicle
manufacturer's design specification or is missing.
Example:
An exhaust pipe has corroded severely and has a hole in it
through which exhaust gases are leaking. Replacement of the
exhaust pipe in this case is required due to functional
failure.
Example:
A brake rotor has been worn to the point where it measures
less than the vehicle manufacturer's discard specifications.
Replacement of the rotor is required because it does not meet
design specifications.

profit organizations. MAP conducted pilot programs in twelve states
before announcing the program nationally in October, 1998. During the
pilots, participating repair shops demonstrated their adherence to the
Pledge and Standards and agreed to follow the UICS in communicating
the results of their inspection to their customers. To put some
"teeth" in the program, an accreditation requirement for shops was
initiated. The requirements are stringent, and a self-policing method
has been incorporated which includes the "mystery shopping" of
outlets.
We welcome you to join us as we continue our outreach... with
your support, both the automotive repair industry and your customers
will reap the benefits. Please visit MAP at our Internet site www.
motorist.org or contact us at:
1444 I Street, NW Suite 700
Washington, DC 20005
Phone (202) 712-9042 Fax (202) 216-9646
January 1999
MAP UNIFORM INSPECTION GENERAL GUIDELINES
OVERVIEW OF SERVICE REQUIREMENTS & SUGGESTIONS
It is MAP policy that all exhaust, brake, steering,
suspension, wheel alignment, drive-line, engine performance and
maintenance, and heating, ventilation and air conditioning, and
electrical services be offered and performed under the standards and
procedures specified in these sections.
Before any service is performed on a vehicle, an inspection
of the appropriate system must be performed. The results of this
inspection must be explained to the customer and documented on an
inspection form. The condition of the vehicle and its components will
indicate what services/part replacements may be "Required" or
"Suggested". In addition, suggestions may be made to satisfy the
requests expressed by the customer.
When a component is suggested or required to be repaired or
replaced, the decision to repair or replace must be made in the
customer's best interest, and at his or her choice given the options
available.
This section lists the various parts and conditions that
indicate a required or suggested service or part replacement.
Although this list is extensive, it is not fully inclusive. In
addition to this list, a technician may make a suggestion. However,
any suggestions must be based on substantial and informed experience,
or the vehicle manufacturer's recommended service interval and must be
documented.
Some conditions indicate that service or part replacement is
required because the part in question is no longer providing the
function for which it is intended, does not meet a vehicle
manufacturer's design specification or is missing.
Example:
An exhaust pipe has corroded severely and has a hole in it
through which exhaust gases are leaking. Replacement of the
exhaust pipe in this case is required due to functional
failure.
Example:
A brake rotor has been worn to the point where it measures
less than the vehicle manufacturer's discard specifications.
Replacement of the rotor is required because it does not meet
design specifications.

Parking Brake cables frozen See DRUM BRAKES
BRAKE SYSTEM
Incorrect installation of
inboard disc pad Remove and replace
correctly
Power booster output
rod too long See POWER BRAKE UNITS
BRAKE SYSTEM
Brake pedal not returning See DISC, DRUM BRAKES
freely BRAKE SYSTEM









\









\









\









\









\









\









\







Brakes Grab or
Uneven Braking
Action Malfunction of combination See CONTROL VALVE or
valve BRAKE SYSTEM
Malfunction of power brake See POWER BRAKE UNITS
unit or BRAKE SYSTEM
Binding brake pedal See DISC, DRUM BRAKES
or BRAKE SYSTEM









\









\









\









\









\









\









\







Pulsation or
Roughness Uneven pad wear caused by See DISC BRAKES or
caliper BRAKE SYSTEM
Uneven rotor wear See DISC BRAKES or
BRAKE SYSTEM
Drums out-of-round Reface or replace drums









\









\









\









\









\









\









\







ENGINE MECHANICAL
COOLING SYSTEM TROUBLE SHOOTING
NOTE: This is GENERAL information. This article is not intended
to be specific to any unique situation or individual vehicle
configuration. The purpose of this Trouble Shooting
information is to provide a list of common causes to
problem symptoms. For model-specific Trouble Shooting,
refer to SUBJECT, DIAGNOSTIC, or TESTING articles available
in the section(s) you are accessing.
COOLING SYSTEM TROUBLE SHOOTING









\









\









\









\









\









\









\







CONDITION POSSIBLE CAUSE CORRECTION








\









\









\









\









\









\









\







Overheating Coolant Leak Fill/Pressure Test
System
A/C Condenser Fins Clogged Remove/Clean Condenser
Radiator Fins Clogged Remove/Clean Radiator
Thermostat Stuck Closed Replace Thermostat
Clogged Cooling System
Passages Clean/Flush Cooling
System

in the section(s) you are accessing.
BASIC GASOLINE ENGINE - MECHANICAL TROUBLE SHOOTING CHART









\









\









\









\









\









\









\







CONDITION POSSIBLE CAUSE CORRECTION








\









\









\









\









\









\









\







Engine Lopes At Intake manifold-to-head Replace manifold
Idle leaks gasket, See ENGINES
Blown head gasket Replace head gasket,
See ENGINES
Worn timing gears, chain Replace gears, chain or
or sprocket sprocket
Worn camshaft lobes Replace camshaft, See
ENGINES
Overheated engine Check cooling system,
See COOLING
Blocked crankcase vent Remove restriction
valve
Leaking EGR valve Repair leak and/or
replace valve
Faulty fuel pump Replace fuel pump









\









\









\









\









\









\









\







Engine Has Low Leaking fuel pump Repair leak and/or
Power replace fuel pump
Excessive piston-to-bore Install larger pistons,
clearance See ENGINES
Sticking valves or weak Check valve train
valve springs components, See ENGINES
Incorrect valve timing Reset valve timing, See
ENGINES
Worn camshaft lobes Replace camshaft, See
ENGINES
Blown head gasket Replace head gasket.
See ENGINES.
Clutch slipping Adjust pedal and/or
replace components, See
ENGINES
Engine overheating Check cooling system,
See COOLING
Auto. Trans. pressure
regulator valve faulty Replace pressure
regulator valve
Auto. Trans. fluid level Add fluid as necessary
too low
Improper vacuum diverter
valve operation Replace vacuum diverter
valve
Vacuum leaks Inspect vacuum system
and repair as required
Leaking piston rings Replace piston rings,
See ENGINES









\









\









\









\









\









\









\







Faulty High Low fuel pump volume Replace fuel pump
Speed Operation
Leaking valves or worn Replace valves and/or
springs, See ENGINES
Incorrect valve timing Reset valve timing,See
ENGINES
Intake manifold restricted Remove restriction
Worn distributor shaft Replace distributor









\









\









\









\









\









\









\







Faulty Improper fuel pump stroke Remove pump and reset
Acceleration pump stroke

Missing valve lock Install new valve lock
Excessively worn camshaft Replace camshaft, See
lobes ENGINES
Plugged valve lifter oil Eliminate restriction
holes or replace lifter
Faulty valve lifter check Replace lifter check
ball ball, See ENGINES
Rocker arm nut installed Remove and reinstall
upside down correctly
Valve lifter incorrect for Remove and replace
engine valve lifters
Faulty push rod seat or Replace plunger or push
lifter plunger rod









\









\









\









\









\









\









\







Noisy Valves Improper valve lash Re-adjust valve lash,
See ENGINES
Worn or dirty valve lifters Clean and/or replace
lifters
Worn valve guides Replace valve guides,
See ENGINES
Excessive valve seat or Reface seats or valve
face run-out face
Worn camshaft lobes Replace camshaft, See
ENGINES
Loose rocker arm studs Re-tighten rocker arm
studs, See ENGINES
Bent push rods Replace push rods, See
ENGINES
Broken valve springs Replace valve springs,
See ENGINES









\









\









\









\









\









\









\







Burned,Sticking Weak valve springs or Replace valves and/or
or Broken Valves warped valves springs, See ENGINES
Improper lifter clearance Re-adjust clearance or
replace lifters
Worn guides or improper Replace valve guides,
guide clearance See ENGINES
Out-of-round valve seats Re-grind valve seats
or improper seat width
Gum deposits on valve Remove deposits
stems, seats or guides
Improper spark timing Re-adjust spark timing









\









\









\









\









\









\









\







Broken Undersize pistons Replace with larger
Pistons/Rings pistons, See ENGINES
Wrong piston rings Replace with correct
rings, See ENGINES
Out-of-round cylinder bore Re-bore cylinder bore
Improper connecting rod Remove and realign
alignment connecting rods
Excessively worn ring Replace pistons, See
grooves ENGINES
Improperly assembled Re-assemble pin-to
piston pins -piston, See ENGINES
Insufficient ring gap Install new rings, See
clearance ENGINES
Engine overheating Check cooling system
Incorrect ignition timing Re-adjust ignition
timing, See TUNE-UP









\









\









\









\









\









\









\







Excessive Leaks at manifold to Replace manifold or
Exhaust Noise head, or to pipe pipe gasket
Exhaust manifold Replace exhaust

Incorrect injector pump Check pressure, see
housing pressure FUEL SYSTEMS









\









\









\









\









\









\









\







Engine Cooling system leaks Check cooling system
Overheating and repair leaks
Belt slipping or damaged Check tension and/or
replace belt
Thermostat stuck closed Remove and replace
thermostat, see
ENGINE COOLING
Head gasket leaking Replace head gasket









\









\









\









\









\









\









\







Oil Light on at Low oil pump pressure Check oil pump
Idle operation, see ENGINES
Oil cooler or line Remove restriction
restricted and/or replace cooler









\









\









\









\









\









\









\







Engine Won't Injector pump fuel solenoid Remove and check
Shut Off does not return fuel valve solenoid and replace
to OFF position if needed









\









\









\









\









\









\









\







VACUUM PUMP DIAGNOSIS
Excessive Noise Loose pump-to-drive Tighten screws
assembly screws
Loose tube on pump assembly Tighten tube
Valves not functioning Replace valves
properly
Oil Leakage Loose end plug Tighten end plug
Bad seal crimp Remove and re-crimp
seal









\









\









\









\









\









\









\







FUEL INJECTION TROUBLE SHOOTING
NOTE: This is GENERAL information. This article is not intended
to be specific to any unique situation or individual vehicle
configuration. The purpose of this Trouble Shooting
information is to provide a list of common causes to
problem symptoms. For model-specific Trouble Shooting,
refer to SUBJECT, DIAGNOSTIC, or TESTING articles available
in the section(s) you are accessing.
BASIC FUEL INJECTION TROUBLE SHOOTING CHART









\









\









\









\









\









\









\







CONDITION POSSIBLE CAUSE CORRECTION








\









\









\









\









\









\









\







Engine Won't Cold start valve inoperative Test valve and
Start (Cranks circuit
Normally)
Poor connection;vacuum or Check vacuum and
wiring electrical
connections
Contaminated fuel Test fuel for water
or alcohol
Defective fuel pump relay Test relay and
or circuit wiring
Battery too low Charge and test
battery

or alcohol
Intermittent ECM ground Test ECM ground
connection for
resistance
Restricted air cleaner Replace air cleaner
Restricted exhaust system Test for exhaust
manifold back
pressure
Poor MAF sensor signal Check leakage
between sensor and
manifold
Poor VSS signal If tester for ALCL
hook-up is available
check that VSS
reading matches
speedometer









\









\









\









\









\









\









\







Ping or Knock on Poor Knock sensor signal Test for shorted or
Acceleration open sensor or
circuit
Poor Baro sensor signal Test for shorted or
open sensor or
circuit
Improper ignition timing See VEHICLE EMISSION
CONTROL LABEL (where
applicable)
Check for engine Low coolant, loose
overheating problems belts or electric
cooling fan
inoperative









\









\









\









\









\









\









\







NOTE: For additional electronic fuel injection trouble shooting
information, see the appropriate article in the ENGINE
PERFORMANCE section (not all vehicles have Computer Engine
Control articles). Information is provided there for
diagnosing fuel system problems on vehicles with electronic
fuel injection.
IGNITION SYSTEM TROUBLE SHOOTING
NOTE: This is GENERAL information. This article is not intended
to be specific to any unique situation or individual vehicle
configuration. The purpose of this Trouble Shooting
information is to provide a list of common causes to
problem symptoms. For model-specific Trouble Shooting,
refer to SUBJECT, DIAGNOSTIC, or TESTING articles available
in the section(s) you are accessing.
Ignition Secondary Trouble Shooting Chart








\









\









\









\









\









\




 
START: Visually inspect Spark Plug Wires, Coil Wires, 

Plug Wire Boots, Rotor, and Distributor Cap for 

signs of damage. 

Excessive cylinder wear Rebore or replace
block
Excessive valve guide Worn or loose bearing
clearance









\









\









\









\









\









\









\







Gap Bridged Deposits in combustion Clean combustion
chamber becoming fused chamber of deposits
to electrode









\









\









\









\









\









\









\







Blistered Engine overheating Check cooling system
Electrode
Wrong type of fuel Replace with correct
fuel
Loose spark plugs Retighten spark plugs
Over-advanced ignition Reset ignition timing
timing see ENGINE PERFORMANCE









\









\









\









\









\









\









\







Pre-Ignition or Incorrect type of fuel Replace with correct
Melted Electrodes fuel
Incorrect ignition timing Reset ignition timing
see ENGINE PERFORMANCE
Burned valves Replace valves
Engine Overheating Check cooling system
Wrong type of spark plug, Replace with correct
too hot spark plug, see
ENGINE PERFORMANCE









\









\









\









\









\









\









\







Chipped Severe detonation Check for over-
Insulators advanced timing or
combustion
Improper gapping Re-gap spark plugs
procedure









\









\









\









\









\









\









\







Rust Colored Additives in unleaded Try different fuel
Deposits fuel brand









\









\









\









\









\









\









\







Water In Combus- Blown head gasket or Repair or replace
tion Chamber cracked head head or head gasket









\









\









\









\









\









\









\







NOTE: Before diagnosing an electronic ignition system, ensure that
all wiring is connected properly between distributor, wiring
connector and spark plugs. Ignition problem will show up
either as: Engine Will Not Start or Engine Runs Rough.
BASIC ELECTRONIC IGNITION TROUBLE SHOOTING CHARTS









\









\









\









\









\









\









\







CONDITION POSSIBLE CAUSE CORRECTION








\









\









\









\









\









\









\







Engine Won't Open circuit between Repair circuit
Start distributor and bulkhead
connector
Open circuit between Repair circuit
bulkhead connector and