ABS MITSUBISHI MONTERO 1998 Manual PDF

the facts, allowing the customer to draw their own
conclusions and make an informed decision about how to
proceed.
STEERING AND SUSPENSION
SERVICE PROCEDURES REQUIRED AND SUGGESTED FOR PROPER VEHICLE
OPERATION
Steering and suspension are complex systems made up of a
variety of interdependent components. For proper vehicle handling,
ride, and tire wear, a thorough inspection is required whenever
suspension work is being performed.
Conditions listed assume that the problem has been isolated
to the specific component by proper testing procedures.
NOTE: When replacing steering and/or suspension components which
may affect an alignment angle, you are required to check
and adjust alignment as needed. Refer to the OEM
specifications.
CAUTION: DO NOT use ride height altering or load compensating
components, such as variable rate springs and coil over
shocks, on vehicles with height or load sensing
proportioning valve-equipped braking systems, unless
these components are original equipment.
AIR RIDE SUSPENSION
NOTE: Depending on the air suspension design, there are some
aftermarket products available to eliminate the air ride
suspension on certain vehicles. If the system has been
eliminated with one of these products, then no service is
suggested or required.
AIR RIDE SUSPENSION - AIR SHOCKS AND AIR STRUTS
NOTE: This section covers the air spring portion of the
air shock or strut. For damping portion of shock
or strut conditions and procedures, refer to the
SHOCK ABSORBERS, STRUT CARTRIDGES AND STRUT ASSEMBLIES
section.
AIR RIDE SUSPENSION - AIR SHOCK AND AIR STRUT INSPECTION









\









\









\









\









\









\









\


Condition Code Procedure
Inner fabric of air bag
damaged ................ A ............ Require replacement.
Leaking ................. A .. Require repair or replacement.
Outer covering of air bag
is cracked to the extent
that inner fabric of air
bag is visible ......... 1 ............ Suggest replacement.









\









\









\









\









\









\









\


AIR RIDE SUSPENSION - AIR SPRING VALVES
AIR RIDE SUSPENSION - AIR SPRING VALVE INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure

Grease fitting missing .. C ... Require replacement of grease
fitting.
Grease fitting
won't seal ............. A ... Require replacement of grease
fitting.
Grease seal missing ..... 2 ........ (5) Suggest replacement.
Grease seal torn ........ 2 ........ ( 4) Suggest replacement.
Looseness (perceptible
horizontal movement) ... 1 ........ ( 6) Suggest replacement.
Looseness that is
excessive .............. B ..... ( 6)( 7) Require replacement.
Seized .................. A ............ Require replacement.
Stud bent ............... B ........ ( 8) Require replacement.
Stud broken ............. A ........ ( 8) Require replacement.
Stud loose in
taper hole ............. A ........... ( 8) Require repair or
replacement.
Taper hole elongated .... A ........ ( 9) Require replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ........ ( 8) Require replacement.
Wear exceeds
manufacturer's
specifications ......... B ............ Require replacement.
( 1) - If greaseable, grease joint. If problem persists or
joint is non-greaseable, require replacement.
( 2) - Cracked grease boot will allow contaminants to enter
the joint and will accelerate wear.
( 3) - Lack of grease boot will allow contaminants to enter
the joint and will accelerate wear.
( 4) - Torn grease boot will allow contaminants to enter the
joint and will accelerate wear.
( 5) - Missing grease seal will allow contaminants to enter
the joint and will accelerate wear.
( 6) - If manufacturer's procedures for inspection exist, use
those procedures; otherwise, use an approved inspection
method such as the dry park check.
CAUTION: DO NOT use pliers or pry bar to check ball and
socket movement. Use only moderate hand pressure.
( 7) - Excessive looseness is defined as being significant
enough to affect vehicle handling or structural
integrity.
( 8) - Check for damaged taper hole.
( 9) - Check for damaged stud.









\









\









\









\









\









\









\


ELECTRONIC RIDE CONTROL SHOCKS AND STRUTS
NOTE: This section covers the electronic damping control portion
of the electronic shock or strut. For dampening portion of
shock or strut conditions and procedures, refer to the
SHOCK ABSORBERS, STRUT CARTRIDGES AND STRUT ASSEMBLIES
section.
ELECTRONIC RIDE CONTROL SHOCK AND STRUT INSPECTION









\









\









\









\









\









\









\


Condition Code Procedure
Connector bent .......... A .. Require repair or replacement.
Connector broken ........ A .. Require repair or replacement.
Connector loose ......... A .. Require repair or replacement.
Electronic valve control

Stud loose in
taper hole ............. A ........... (7) Require repair or
replacement.
Taper hole elongated .... A ........ ( 8) Require replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ........ ( 7) Require replacement.
Wear exceeds
manufacturer's
specifications .......... B ............ Require replacement.
( 1) - If greaseable, grease joint. If problem persists or
joint is non-greaseable, require replacement.
( 2) - Cracked grease boot will allow contaminants to enter
the joint and will accelerate wear.
( 3) - Lack of grease boot will allow contaminants to enter
the joint and will accelerate wear.
( 4) - Torn grease boot will allow contaminants to enter the
joint and will accelerate wear.
( 5) - If manufacturer's procedures for inspection exist, use
those procedures; otherwise, use an approved inspection
method such as the dry park check.
CAUTION: DO NOT use pliers or pry bar to check ball and
socket movement. Use only moderate hand pressure.
( 6) - Excessive looseness is defined as being significant
enough to affect vehicle handling or structural
integrity.
( 7) - Check for damaged taper hole.
( 8) - Check for damaged stud.









\









\









\









\









\









\









\


SHOCK ABSORBERS, STRUT CARTRIDGES AND STRUT ASSEMBLIES
You are not required to replace shocks or struts in axle
sets. However, when replacing a shock or strut due to the conditions
that follow, you may suggest replacement of the other shock or strut
on the same axle for improved performance and preventive maintenance.
* Part is close to the end of its useful life
* To extend tire life
* To balance ride and handling
* To improve stopping distance
When replacing steering and/or suspension components which
may affect an alignment angle, you are required to check and adjust
alignment as needed. Refer to the OEM specifications.
Under no circumstances should a technician bend struts or
strut housings.
A vehicle's load-carrying and handling abilities are limited
by its suspension, tires, brakes, and driveline. Installing coil over
shocks or any other load assist device does not increase the vehicle's
load capacity. See the vehicle owner's manual for more details.
NOTE: If vehicle is equipped with original equipment coil over
shocks, apply the conditions for coil springs from the
SPRINGS - COIL, LEAF AND TORSION BAR section of the
STEERING AND SUSPENSION guidelines. If the vehicle is
equipped with add-on coil over shocks, you may suggest
replacing the shocks with standard shocks for any spring-
related condition.
SHOCK ABSORBER, STRUT CARTRIDGE AND STRUT ASSEMBLY INSPECTION









\









\









\









\









\









\









\

Threads stripped
(threads missing) ...... A ..... Require replacement of part
with stripped threads.
U-joint binding ......... A ... Require repair or replacement
of joint.
U-joint loose ........... A ... Require repair or replacement
of joint.
Unequal power assist .... A .. Require repair or replacement.
(1) - Determine and correct source of contamination. Follow OE
specifications for fluid type.
( 2) - Indicates internal wear.
( 3) - If steering gear is source of inadequate assist, require
repair or replacement.









\









\









\









\









\









\









\


STEERING KNUCKLES
STEERING KNUCKLE INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Attaching hardware
bent ................... B ... Require repair or replacement
of bent part.
Attaching hardware
broken ................. A ... Require replacement of broken
part.
Attaching hardware
incorrect .............. A .......... Require replacement of
incorrect part.
Attaching hardware
loose .................. A ... Require repair or replacement
of loose part.
Attaching hardware
missing ................ C .. Require replacement of missing
part.
Attaching hardware
threads damaged ........ A ... Require repair or replacement
of part with damaged threads.
Attaching hardware
threads stripped
(threads missing) ...... A ..... Require replacement of part
with stripped threads.
Bent .................... B ............ Require replacement.
Broken .................. A ............ Require replacement.
Pinch bolt incorrect .... B ... Require replacement with bolt
that meets OE design.
Pinch bolt loose ........ B ................. Require repair.
Pinch bolt missing ...... B ............ Require replacement.
Pinch bolt tabs
deformed (pinched
together), .032"
or more before
clamping ............... B ........ ( 1) Require replacement.
Taper hole elongated .... A ........ ( 2) Require replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A .. Require repair or replacement.
( 1) - Steering knuckle deformation can cause pinch
bolt breakage.
( 2) - Check for damaged stud.

knuckles steering linkage
Rack and pinion mounting Tighten all mounting
loose bolts
Rack and pinion out of See adjustment in
adjustment STEERING article
Tie rod end loose Tighten and check
steering linkage
Excessive Pitman shaft-to- Repair as necessary
ball nut lash









\









\









\









\









\









\









\







Poor Lack of lubricant in ball Lubricate and service
Returnability joint or linkage systems
Binding in linkage or ball See STEERING LINKAGE
joints and SUSPENSION article
Improper front end alignment See WHEEL ALIGNMENT
article
Improper tire pressure Inflate to proper
pressure
Tie rod binding Inflate to proper
pressure
Shaft seal rubbing shaft See STEERING COLUMN
article









\









\









\









\









\









\









\







Excessive Improper tire pressure Inflate to proper
Vertical Motion pressure
Tires, wheels or rotors Balance tires then
out of balance check wheels and
rotors
Worn or faulty shock Check and replace if
absorbers necessary
Loose tie rod ends or Tighten or replace if
steering necessary
Loose or worn wheel See SUSPENSION article
bearings









\









\









\









\









\









\









\







Steering Pulls Improper tire pressure Inflate to proper
to One Side pressure
Front tires are different Rotate or replace if
sizes necessary
Wheel bearings not See FRONT SUSPENSION
article
adjusted properly
Bent or broken suspension See FRONT SUSPENSION
components article
Improper wheel alignment See WHEEL ALIGNMENT
article

Loose or worn wheel See WHEEL ALIGNMENT
bearings
Loose or worn tie rod ends See SUSPENSION
Worn upper ball joints See Ball Joint Checking
in SUSPENSION
Worn shock absorbers Replace shock absorbers
Worn strut bushings Replace strut bushings









\









\









\









\









\









\









\







Car Pulls to Mismatched or uneven tires Check tire condition
One Side
Broken or sagging springs See SUSPENSION
Loose or worn strut See SUSPENSION
bushings
Improper wheel alignment See WHEEL ALIGNMENT
Improper rear axle Check rear axle
alignment alignment
Power steering gear See STEERING
unbalanced
Front brakes dragging See BRAKES









\









\









\









\









\









\









\







Abnormal Tire Unbalanced tires Check tire balance &
Wear rotation
Sagging or broken springs See SUSPENSION
Incorrect front end See WHEEL ALIGNMENT
alignment
Faulty shock absorbers Replace chock absorbers









\









\









\









\









\









\









\







Scuffed Tires Toe-In incorrect See WHEEL ALIGNMENT
Suspension arm bent or See appropriate
twisted SUSPENSION article









\









\









\









\









\









\









\







Springs Bottom Bent or broken springs See SUSPENSION
or Sag
Leaking or worn shock Replace shock absorbers
absorbers
Frame misalignment Check frame for damage









\









\









\









\









\









\









\







Spring Noises Loose "U" Bolts See SUSPENSION
Loose or worn bushings See SUSPENSION
Worn or missing interliners See SUSPENSION









\









\









\









\









\









\









\







Shock Absorber Loose shock mountings Check & tighten
Noise mountings
Worn bushings Replace bushings

Air in system Bleed air from system
Undercoating on shocks Remove undercoating









\









\









\









\









\









\









\







Car Leans or Loose stabilizer bar See SUSPENSION
Sways on Corners
Faulty shocks or mountings Replace shocks or
mountings
Broken or sagging springs See SUSPENSION









\









\









\









\









\









\









\







Shock Absorbers Worn seals or reservoir See SUSPENSION
Leaking tube crimped









\









\









\









\









\









\









\







Broken Springs Loose "U" bolts See SUSPENSION
Inoperative shock absorbers Replace shock absorbers









\









\









\









\









\









\









\







WHEEL ALIGNMENT TROUBLE SHOOTING
NOTE: This is GENERAL information. This article is not intended
to be specific to any unique situation or individual vehicle
configuration. The purpose of this Trouble Shooting
information is to provide a list of common causes to
problem symptoms. For model-specific Trouble Shooting,
refer to SUBJECT, DIAGNOSTIC, or TESTING articles available
in the section(s) you are accessing.
BASIC WHEEL ALIGNMENT TROUBLE SHOOTING CHART









\









\









\









\









\









\









\







CONDITION POSSIBLE CAUSE CORRECTION








\









\









\









\









\









\









\







Premature Tire Improper tire inflation Check tire pressure
Wear
Front alignment out of See ALIGNMENT SPECS in
tolerance WHEEL ALIGNMENT section
Suspension components worn See SUSPENSION section
Steering system components See STEERING section
worn
Improper standing height See WHEEL ALIGNMENT
Uneven or sagging springs See SUSPENSION section
Bent wheel See WHEEL ALIGNMENT
Improper torsion bar See SUSPENSION section
adjustment
Loose or worn wheel See WHEEL BEARING ADJ.
bearings in SUSPENSION section
Worn or defective shock Replace shock absorbers
Tires out of balance Check tire balance









\









\









\









\









\









\









\







Pulls to One Improper tire inflation Check tire pressure
Side
Brake dragging See BRAKE section

Wheel alignment out of See Adjustment in
tolerance WHEEL ALIGNMENT section
Broken spring See SUSPENSION section
Defective shock absorbers Replace shock absorbers
Worn steering & suspension See SUSPENSION section
components









\









\









\









\









\









\









\







Front End Shimmy Tire out of balance/round Check tire balance
Excessive wheel runout See WHEEL ALIGNMENT
Insufficient or improper See WHEEL ALIGNMENT
caster section
Worn suspension or steering See SUSPENSION section
components
Defective shock absorbers Replace shock absorber
Wheel bearings worn or See WHEEL BEARING ADJ.
loose in SUSPENSION section
Power steering reaction See STEERING section
Bracket loose
Steering gear box (rack) See STEERING section
mounting loose
Steering gear adjustment See STEERING section
loose
Worn spherical joints See SUSPENSION section









\









\









\









\









\









\









\







Toe-In Not Lower control arm bent See SUSPENSION section
Adjustable
Frame bent Check frame for damage









\









\









\









\









\









\









\







Camber Not Control arm bent See SUSPENSION section
Adjustable
Frame bent Check frame for damage
Hub & bearing not seated See SUSPENSION section
properly









\









\









\









\









\









\









\

WHEEL ALIGNMENT PROCEDURES
CAMBER ADJUSTMENT
Except Montero, Montero Sport & 3000GT
Camber is preset and cannot be adjusted. Check camber. See
appropriate table under WHEEL ALIGNMENT SPECIFICATIONS . If camber is
not within specification, replace damaged or bent parts.
Montero & Montero Sport
1) Check camber. See appropriate table under
WHEEL ALIGNMENT SPECIFICATIONS . If camber is not within specification,
remove shock absorber mounting nut and lock nut.
CAUTION: Difference in shim thickness between front and rear must not
exceed 0.16" (4.0 mm). DO NOT use more than 3 shims at
onelocation.
2) Compress shock absorber, and loosen upper arm mounting
bolts and nuts. Adjust camber by increasing or decreasing shims
between upper arm shaft and crossmember. See Fig. 6.
Fig. 6: Adjusting Camber & Caster (Montero Sport Shown; Montero Is
Similar)
Courtesy of Mitsubishi Motor Sales of America.
3000GT
Check camber. See WHEEL ALIGNMENT SPECIFICATIONS (3000GT)
table. If camber is not within specification, loosen eccentric cam
nut. Rotate eccentric cam bolt to obtain correct camber. See Fig. 7.
Each marking represents a change of .12-.25 degree of camber.

Fig. 7: Adjusting Camber (3000GT)
Courtesy of Mitsubishi Motor Sales of America.
CASTER ADJUSTMENT
Except Montero & Montero Sport
Check caster. See appropriate table under
WHEEL ALIGNMENT SPECIFICATIONS . If caster is not within specification,
replace damaged or bent parts.
Montero & Montero Sport
1) Check caster. See appropriate table under
WHEEL ALIGNMENT SPECIFICATIONS . If caster is not within specification,
remove shock absorber mounting nut and lock nut.
CAUTION: Difference in shim thickness between front and rear must not
exceed .16" (4.0 mm). DO NOT use more than 3 shims at one
location.
2) Compress shock absorber, and loosen upper arm mounting
bolts and nuts. Adjust caster by increasing or decreasing shims
between upper arm shaft and crossmember. See Fig. 6.
TOE-IN ADJUSTMENT
Front
Check front toe-in. See appropriate table under
WHEEL ALIGNMENT SPECIFICATIONS . If front toe-in is not within
specification, remove clips. Turn tie rods or turnbuckles same amount,
but in opposite directions. Recheck front toe-in.
Rear (Montero & Montero Sport)
Check rear toe-in. See appropriate table under