camshaft NISSAN 350Z 2007 Z33 Engine Control User Guide

TROUBLE DIAGNOSIS
EC-87
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: 2006 November2007 350Z
DTC Inspection Priority ChartNBS0003E
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority
chart.
NOTE:

If DTC U1000 or U1001 is displayed with other DTC, first perform the trouble diagnosis for DTC
U1000, U1001. Refer to EC-151, "
DTC U1000, U1001 CAN COMMUNICATION LINE" .

If DTC U1010 is displayed with other DTC, first perform the diagnosis for DTC U1010.
Refer to EC-154, "
DTC U1010 CAN COMMUNICATION".
Priority Detected items (DTC)
1

U1000 U1001 CAN communication line

U1010 CAN communication

P0101 P0102 P0103 P010B P010C P010D Mass air flow sensor

P0112 P0113 P0127 Intake air temperature sensor

P0117 P0118 P0125 Engine coolant temperature sensor

P0122 P0123 P0222 P0223 P0227 P0228 P1225 P1226 P1234 P1235 P1239 P2132 P2133 P2135 Throttle position
sensor

P0128 Thermostat function

P0181 P0182 P0183 Fuel tank temperature sensor

P0196 P0197 P0198 Engine oil temperature sensor

P0327 P0328 P0332 P0333 Knock sensor

P0335 Crankshaft position sensor (POS)

P0340 P0345 Camshaft position sensor (PHASE)

P0460 P0461 P0462 P0463 Fuel level sensor

P0500 Vehicle speed sensor

P0605 ECM

P0643 Sensor power supply

P0700 TCM

P0705 P0850 Park/neutral position (PNP) switch

P1610 - P1615 NATS

P2122 P2123 P2127 P2128 P2138 Accelerator pedal position sensor

TROUBLE DIAGNOSIS
EC-91
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: 2006 November2007 350Z
1 - 6: The numbers refer to the order of inspection.
(continued on next page)Mass air flow sensor circuit
1
122
222 2EC-197
,
EC-208
Engine coolant temperature sensor circuit
333EC-223,
EC-239
Air fuel ratio (A/F) sensor 1 circuitEC-165
,
EC-248
,
EC-257
,
EC-266
,
EC-275
,
EC-659
Throttle position sensor circuit
22EC-229
,
EC-361
,
EC-557
,
EC-559
,
EC-582
Accelerator pedal position sensor circuit 3 2 1EC-514
,
EC-633
,
EC-641
,
EC-650
Knock sensor circuit 2 3EC-379
Crankshaft position sensor (POS) circuit 2 2EC-386
Camshaft position sensor (PHASE) circuit 3 2EC-394
Vehicle speed signal circuit 2 3 3 3EC-496
Power steering pressure sensor circuit 2 3 3EC-502
ECM 22333333333EC-508,
EC-512
Intake valve timing control solenoid valve cir-
cuit32 13223 3EC-183
Exhaust valve timing control magnet retarder
circuit32 13223 3EC-160
Park/neutral position (PNP) switch circuit 3 3 3 3 3EC-520
Refrigerant pressure sensor circuit 2 3 3 4EC-710
Electrical load signal circuit 3EC-684
Air conditioner circuit223333333 3 2AT C - 3 3
VDC/TCS/ABS control unit
ABS actuator and electric unit (control unit)4BRC-82,
BRC-42
SYMPTOM
Reference
page
HARD/NO START/RESTART (EXCP. HA)
ENGINE STALL
HESITATION/SURGING/FLAT SPOT
SPARK KNOCK/DETONATION
LACK OF POWER/POOR ACCELERATION
HIGH IDLE/LOW IDLE
ROUGH IDLE/HUNTING
IDLING VIBRATION
SLOW/NO RETURN TO IDLE
OVERHEATS/WATER TEMPERATURE HIGH
EXCESSIVE FUEL CONSUMPTION
EXCESSIVE OIL CONSUMPTION
BATTERY DEAD (UNDER CHARGE)
Warranty symptom code AA AB AC AD AE AF AG AH AJ AK AL AM HA

TROUBLE DIAGNOSIS
EC-93
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: 2006 November2007 350Z
1 - 6: The numbers refer to the order of inspection.Va l v e
mecha-
nismTiming chain
55555 55 5EM-53
CamshaftEM-72
Intake valve timing controlEM-53
Exhaust valve timing controlEM-53
Intake valve
3EM-89
Exhaust valve
Exhaust Exhaust manifold/Tube/Muffler/
Gasket
55555 55 5EM-22
, EX-
3Three way catalyst
Lubrica-
tionOil pan/Oil strainer/Oil pump/Oil
filter/Oil gallery
55555 55 5EM-26
, LU-
10 , LU-9
Oil level (Low)/Filthy oilLU-6
Cooling
Radiator/Hose/Radiator filler cap
55555 55 45CO-13,
CO-17
Thermostat 5CO-26
Water pumpCO-23
Water galleryCO-28
Cooling fan 5CO-21
Coolant level (Low)/Contami-
nated coolantCO-10
NVIS (NISSAN Vehicle Immobilizer System —
NATS)11EC-46 or
BL-150
SYMPTOM
Reference
page
HARD/NO START/RESTART (EXCP. HA)
ENGINE STALL
HESITATION/SURGING/FLAT SPOT
SPARK KNOCK/DETONATION
LACK OF POWER/POOR ACCELERATION
HIGH IDLE/LOW IDLE
ROUGH IDLE/HUNTING
IDLING VIBRATION
SLOW/NO RETURN TO IDLE
OVERHEATS/WATER TEMPERATURE HIGH
EXCESSIVE FUEL CONSUMPTION
EXCESSIVE OIL CONSUMPTION
BATTERY DEAD (UNDER CHARGE)
Warranty symptom code AA AB AC AD AE AF AG AH AJ AK AL AM HA

EC-94
TROUBLE DIAGNOSIS
Revision: 2006 November2007 350Z
Engine Control Component Parts LocationNBS0003I
1. IPDM E/R 2. Mass air flow sensor (with intake air
temperature sensor) (bank 1)3. Refrigerant pressure sensor
4. Cooling fan motor-2 5. Intake valve timing control solenoid
valve6. Exhaust valve timing control magnet
retarder
7. Cooling fan motor-1 8. Mass air flow sensor (with intake air
temperature sensor) (bank 2)9. Ignition coil (with power transistor)
and spark plug (bank 2)
10. Electric throttle control actuator
(bank 2)11. A/F sensor 1 (bank 2) 12. Exhaust valve timing control position
sensor
13. Camshaft position sensor (PHASE) 14. Fuel injector (bank 2) 15. Engine coolant temperature sensor
16. Knock sensor 17. EVAP canister purge volume con-
trol solenoid valve18. Fuel injector (bank 1)
19. Ignition coil (with power transistor)
and spark plug (bank 1)20. EVAP service port 21. A/F sensor 1 (bank 1)
22. Crankshaft position sensor (POS) 23. Electric throttle control actuator
(bank 1)
PBIB3474E

TROUBLE DIAGNOSIS
EC-95
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: 2006 November2007 350Z
1. Mass air flow sensor (with intake air
temperature sensor) (bank 1)2. Mass air flow sensor (with intake air
temperature sensor) (bank 2)
1. Electric throttle control actuator
(bank 1)2. Electric throttle control actuator
(bank 2)
1. Exhaust valve timing control magnet
retarder (bank 1) harness connector2. Intake valve timing control solenoid
valve (bank 1) harness connector3. Intake valve timing control solenoid
valve (bank 2) harness connector
4. Exhaust valve timing control magnet
retarder (bank 2) harness connector
1. Exhaust valve timing control position
sensor (bank 1)2. Camshaft position sensor (PHASE)
(bank 1)3. Camshaft position sensor (PHASE)
(bank 2)
4. Exhaust valve timing control position
sensor (bank 2)
PBIB3501E
PBIB3504E
PBIB3508E
PBIB3518E

TROUBLE DIAGNOSIS
EC-109
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: 2006 November2007 350Z
50 PU/WThrottle control motor
(Open) (bank 2)[Ignition switch: ON]

Engine stopped

Shift lever: D (A/T) or 1st (M/T)

Accelerator pedal: Fully depressed0 - 14V
[Ignition switch: ON]

Engine stopped

Shift lever: D (A/T) or 1st (M/T)

Accelerator pedal: Fully released0 - 14V
52 R/WThrottle control motor relay
power supply (bank 2)[Ignition switch: ON]BATTERY VOLTAGE
(11 - 14V)
53 P/L Ignition switch[Ignition switch: OFF]0V
[Ignition switch: ON]BATTERY VOLTAGE
(11 - 14V)
57 L A/F sensor 1 (bank 1)[Ignition switch: ON]2.2V
58 Y/GExhaust valve timing control
position sensor (bank 1)[Engine is running]

Warm-up condition

Idle speed
NOTE:
The pulse cycle changes depending on rpm at
idle.4.0 - 5.0V
[Engine is running]

Warm-up condition

Engine speed: 2,000 rpm4.0 - 5.0V
59 BR/YCamshaft position sensor
(PHASE) (bank 1)[Engine is running]

Warm-up condition

Idle speed
NOTE:
The pulse cycle changes depending on rpm at
idle.3.0 - 5.0V
[Engine is running]

Engine speed: 2,000 rpm3.0 - 5.0V TER-
MINAL
NO.WIRE
COLORITEM CONDITION DATA (DC Voltage)
PBIB3539E
PBIB3540E
PBIB3551E
PBIB3552E
PBIB3553E
PBIB3554E

EC-110
TROUBLE DIAGNOSIS
Revision: 2006 November2007 350Z
60 R/LSensor power supply
[Camshaft position sensor
(PHASE) (bank 1), Exhaust
valve timing control position
sensor (bank 1), Power
steering pressure sensor][Ignition switch: ON]5V
61 R A/F sensor 1 (bank 1)[Ignition switch: ON]

Warm-up condition

Engine speed: 2,000 rpm1.8V
Output voltage varies with air
fuel ratio.
62 B/YExhaust valve timing control
position sensor (bank 2)[Engine is running]

Warm-up condition

Idle speed
NOTE:
The pulse cycle changes depending on rpm at
idle.4.0 - 5.0V
[Engine is running]

Warm-up condition

Engine speed: 2,000 rpm4.0 - 5.0V
63 SBCamshaft position sensor
(PHASE) (bank 2)[Engine is running]

Warm-up condition

Idle speed
NOTE:
The pulse cycle changes depending on rpm at
idle.3.0 - 5.0V
[Engine is running]

Engine speed: 2,000 rpm1.0 - 4.0V
64 W/GSensor power supply
[Camshaft position sensor
(PHASE) (bank 2), Exhaust
valve timing control position
sensor (bank 2)][Ignition switch: ON]5V
65 PU A/F sensor 1 (bank 2)[Ignition switch: ON]2.2V
66 LG A/F sensor 1 (bank 2)[Ignition switch: ON]

Warm-up condition

Engine speed: 2,000 rpm1.8V
Output voltage varies with air
fuel ratio.
67 W/LIntake air temperature sen-
sor (bank 1)[Engine is running]0 - 4.8V
Output voltage varies with intake
air temperature. TER-
MINAL
NO.WIRE
COLORITEM CONDITION DATA (DC Voltage)
PBIB3551E
PBIB3552E
PBIB3553E
PBIB3554E

EC-112
TROUBLE DIAGNOSIS
Revision: 2006 November2007 350Z
81
82
85
86
89
90R/B
L/R
BR
W/B
G/Y
Y/RFuel injector No. 3
Fuel injector No. 6
Fuel injector No. 2
Fuel injector No. 5
Fuel injector No. 1
Fuel injector No. 4[Engine is running]

Warm-up condition

Idle speed
NOTE:
The pulse cycle changes depending on rpm at
idle.BATTERY VOLTAGE
(11 - 14V)
[Engine is running]

Warm-up condition

Engine speed: 2,000 rpmBATTERY VOLTAGE
(11 - 14V)
83 GIntake air temperature sen-
sor (bank 2)[Engine is running]0 - 4.8V
Output voltage varies with intake
air temperature.
84 GSensor ground
(Heated oxygen sensor 2,
Engine coolant temperature
sensor, Engine oil tempera-
ture sensor)[Engine is running]

Warm-up condition

Idle speed0V
87 YPower steering pressure
sensor[Engine is running]

Steering wheel: Being turned0.5 - 4.5V
[Engine is running]

Steering wheel: Not being turned0.4 - 0.8V
88 LG/BSensor ground
[Exhaust valve timing con-
trol position sensor (bank 1),
Exhaust valve timing control
position sensor (bank 2)][Engine is running]

Warm-up condition

Idle speed0V
92 B/PSensor ground
[Camshaft position sensor
(PHASE) (bank 2)][Engine is running]

Warm-up condition

Idle speed0V
93 PPower supply for ECM
(Back-up)[Ignition switch: OFF]BATTERY VOLTAGE
(11 - 14V)
94 L/YSensor ground
[Mass air flow sensor (bank
2)][Engine is running]

Warm-up condition

Idle speed0V
96 P/LSensor ground
[Camshaft position sensor
(PHASE) (bank 1), Power
steering pressure sensor][Engine is running]

Warm-up condition

Idle speed0V
97 RAccelerator pedal position
sensor 1[Ignition switch: ON]

Engine stopped

Accelerator pedal: Fully released0.5 - 1.0V
[Ignition switch: ON]

Engine stopped

Accelerator pedal: Fully depressed3.9 - 4.7V TER-
MINAL
NO.WIRE
COLORITEM CONDITION DATA (DC Voltage)
PBIB3555E
PBIB3556E

TROUBLE DIAGNOSIS
EC-117
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: 2006 November2007 350Z
ENGINE CONTROL COMPONENT PARTS/CONTROL SYSTEMS APPLICATION
ItemDIAGNOSTIC TEST MODE
WORK
SUPPORTSELF-DIAGNOSTIC
RESULTS
DATA
MONI-
TORACTIVE
TESTDTC & SRT
CONFIRMATION
DTC*1FREEZE
FRAME
DATA*
2
SRT STA-
TUSDTC
WORK
SUP-
PORT
ENGINE CONTROL COMPONENT PARTS
INPUT
Crankshaft position sensor (POS)×××
Camshaft position sensor (PHASE)×××
Mass air flow sensor××
Engine coolant temperature sensor××××
Engine oil temperature sensor×
Air Fuel ratio (A/F) sensor 1××××
Heated oxygen sensor 2××××
Vehicle speed sensor×××
Accelerator pedal position sensor××
Throttle position sensor×××
Fuel tank temperature sensor×××
EVAP control system pressure sensor××
Intake air temperature sensor×××
Knock sensor×
Refrigerant pressure sensor×
Closed throttle position switch (accel-
erator pedal position sensor signal)×
Air conditioner switch×
Park/neutral position (PNP) switch××
Stop lamp switch××
Power steering pressure sensor××
Battery voltage×
Load signal×
Exhaust valve timing control position
sensor××
Fuel level sensor××
ASCD steering switch××
ASCD brake switch××
ASCD clutch switch××

EC-120
TROUBLE DIAGNOSIS
Revision: 2006 November2007 350Z
*: This item is the same as that of 1st trip freeze frame data.
DATA MONITOR MODE
Monitored Item
×: Applicable ENGINE SPEED
[rpm]

The engine speed at the moment a malfunction is detected is displayed.
VEHICL SPEED
[km/h] or [mph]

The vehicle speed at the moment a malfunction is detected is displayed.
ABSOL TH-P/S [%]

The throttle valve operating angle at the moment a malfunction is detected is displayed.
B/FUEL SCHDL
[msec]

The base fuel schedule at the moment a malfunction is detected is displayed.
INT/A TEMP SE
[°C] or [°F]

The intake air temperature at the moment a malfunction is detected is displayed. Freeze frame data
item*Description
Monitored item [Unit] Description Remarks
ENG SPEED [rpm]

Indicates the engine speed computed from the signals
of the crankshaft position sensor (POS) and camshaft
position sensor (PHASE).
Accuracy becomes poor if engine speed drops
below the idle rpm.

If the signal is interrupted while the engine is
running, an abnormal value may be indicated.
MAS A/F SE-B1 [V]

The signal voltage of the mass air flow sensor is dis-
played.

When the engine is stopped, a certain value is
indicated.

When engine is running specification range is
indicated in “SPEC”. MAS A/F SE-B2 [V]
B/FUEL SCHDL [msec]

“Base fuel schedule” indicates the fuel injection pulse
width programmed into ECM, prior to any learned on
board correction.
When engine is running specification range is
indicated in “SPEC”.
A/F ALPHA-B1 [%]

The mean value of the air-fuel ratio feedback correc-
tion factor per cycle is indicated.

When the engine is stopped, a certain value is
indicated.

This data also includes the data for the air-fuel
ratio learning control.

When engine is running specification range is
indicated in “SPEC”. A/F ALPHA-B2 [%]
COOLAN TEMP/S [°C]
or [°F]

The engine coolant temperature (determined by the
signal voltage of the engine coolant temperature sen-
sor) is displayed.
When the engine coolant temperature sensor
is open or short-circuited, ECM enters fail-safe
mode. The engine coolant temperature deter-
mined by the ECM is displayed.
A/F SEN1 (B1) [V]

The A/F signal computed from the input signal of the
A/F sensor 1 is displayed.
A/F SEN1 (B2) [V]
HO2S2 (B1) [V]

The signal voltage of the heated oxygen sensor 2 is
displayed.
HO2S2 (B2) [V]
HO2S2 MNTR(B1)
[RICH/LEAN]

Display of heated oxygen sensor 2 signal:
RICH: Means the amount of oxygen after three way
catalyst is relatively small.
LEAN: Means the amount of oxygen after three way
catalyst is relatively large.

When the engine is stopped, a certain value is
indicated.
HO2S2 MNTR(B2)
[RICH/LEAN]
VHCL SPEED SE [km/
h] or [mph]

The vehicle speed computed from the vehicle speed
signal sent from combination meter is displayed.
BATTERY VOLT [V]

The power supply voltage of ECM is displayed.
ACCEL SEN 1 [V]

The accelerator pedal position sensor signal voltage is
displayed.
ACCEL SEN 2 signal is converted by ECM
internally. Thus, it differs from ECM terminal
voltage signal. ACCEL SEN 2 [V]