sensor NISSAN 350Z 2007 Z33 Engine Control User Guide

EC-12
INDEX FOR DTC
Revision: 2006 November2007 350Z
*1: 1st trip DTC No. is the same as DTC No.
*2: This number is prescribed by SAE J2012.
*3: In Diagnostic Test Mode II (Self-diagnostic results), this number is controlled by NISSAN.
*4: The troubleshooting for this DTC needs CONSULT-III.P2A00 2A00 A/F SENSOR1 (B1)EC-659
P2A03 2A03 A/F SENSOR1 (B2)EC-659
DTC*1
Items
(CONSULT-III screen terms)Reference page
CONSULT-III
GST*
2ECM*3

INDEX FOR DTC
EC-13
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: 2006 November2007 350Z
Alphabetical IndexNBS00028
NOTE:

If DTC U1000 or U1001 is displayed with other DTC, first perform the trouble diagnosis for DTC
U1000, U1001. Refer to EC-151, "
DTC U1000, U1001 CAN COMMUNICATION LINE" .

If DTC U1010 is displayed with other DTC, first perform the diagnosis for DTC U1010.
Refer to EC-154, "
DTC U1010 CAN COMMUNICATION" .
Items
(CONSULT-III screen terms)DTC*
1
Reference page
CONSULT-III
GST*
2ECM*3
A/F SEN1 HTR (B1) P0031 0031EC-165
A/F SEN1 HTR (B1) P0032 0032EC-165
A/F SEN1 HTR (B2) P0051 0051EC-165
A/F SEN1 HTR (B2) P0052 0052EC-165
A/F SENSOR1 (B1) P0130 0130EC-248
A/F SENSOR1 (B1) P0131 0131EC-257
A/F SENSOR1 (B1) P0132 0132EC-266
A/F SENSOR1 (B1) P0133 0133EC-275
A/F SENSOR1 (B1) P2A00 2A00EC-659
A/F SENSOR1 (B2) P0150 0150EC-248
A/F SENSOR1 (B2) P0151 0151EC-257
A/F SENSOR1 (B2) P0152 0152EC-266
A/F SENSOR1 (B2) P0153 0153EC-275
A/F SENSOR1 (B2) P2A03 2A03EC-659
A/T 1ST GR FNCTN P0731 0731AT- 11 5
A/T 2ND GR FNCTN P0732 0732AT- 11 7
A/T 3RD GR FNCTN P0733 0733AT- 11 9
A/T 4TH GR FNCTN P0734 0734AT- 1 2 1
A/T 5TH GR FNCTN P0735 0735AT- 1 2 3
A/T INTERLOCK P1730 1730AT- 1 4 1
A/T TCC S/V FNCTN P0744 0744AT- 1 2 7
APP SEN 1/CIRC P2122 2122EC-633
APP SEN 1/CIRC P2123 2123EC-633
APP SEN 2/CIRC P2127 2127EC-641
APP SEN 2/CIRC P2128 2128EC-641
APP SENSOR P2138 2138EC-650
ASCD BRAKE SW P1572 1572EC-610
ASCD SW P1564 1564EC-602
ASCD VHL SPD SEN P1574 1574EC-625
ATF TEMP SEN/CIRC P0710 0710AT- 1 3 4
BRAKE SW/CIRCUIT P1805 1805EC-628
CAN COMM CIRCUIT U1000
1000*4EC-151
CAN COMM CIRCUIT U1001
1001*4EC-151
CKP SEN/CIRCUIT P0335 0335EC-386
CLOSED LOOP-B1 P1148 1148EC-540
CLOSED LOOP-B2 P1168 1168EC-540
CMP SEN/CIRC-B1 P0340 0340EC-394

EC-14
INDEX FOR DTC
Revision: 2006 November2007 350Z
CMP SEN/CIRC-B2 P0345 0345EC-394
COLD START CONTROL P1421 1421EC-600
CONTROL UNIT(CAN) U1010 1010EC-154
CTP LEARNING-B1 P1225 1225EC-557
CTP LEARNING-B1 P1226 1226EC-559
CTP LEARNING-B2 P1234 1234EC-557
CTP LEARNING-B2 P1235 1235EC-559
CYL 1 MISFIRE P0301 0301EC-371
CYL 2 MISFIRE P0302 0302EC-371
CYL 3 MISFIRE P0303 0303EC-371
CYL 4 MISFIRE P0304 0304EC-371
CYL 5 MISFIRE P0305 0305EC-371
CYL 6 MISFIRE P0306 0306EC-371
D/C SOLENOID/CIRC P1762 1762AT-149
ECM P0605 0605EC-512
ECM BACK UP/CIRCUIT P0603 0603EC-508
ECT SEN/CIRC P0117 0117EC-223
ECT SEN/CIRC P0118 0118EC-223
ECT SENSOR P0125 0125EC-239
ENG OVER TEMP P1217 1217EC-543
EOT SEN/CIRC P0197 0197EC-223
EOT SEN/CIRC P0198 0198EC-223
EOT SENSOR P0196 0196EC-352
ETC ACTR-B1 P2119 2119EC-580
ETC ACTR-B2 P1238 1238EC-580
ETC FUNCTION/CIRC-B1 P2101 2101EC-561
ETC FUNCTION/CIRC-B2 P1233 1233EC-561
ETC MOT PWR P2103 2103EC-592
ETC MOT PWR-B1 P2100 2100EC-592
ETC MOT PWR-B2 P1290 1290EC-592
ETC MOT-B1 P2118 2118EC-571
ETC MOT-B2 P1236 1236EC-571
EVAP GROSS LEAK P0455 0455EC-475
EVAP PURG FLOW/MON P0441 0441EC-411
EVAP SMALL LEAK P0442 0442EC-416
EVAP SYS PRES SEN P0451 0451EC-450
EVAP SYS PRES SEN P0452 0452EC-456
EVAP SYS PRES SEN P0453 0453EC-465
EVAP VERY SML LEAK P0456 0456EC-482
EX V/T MGT/RTDR-B1 P0078 0078EC-190
EX V/T MGT/RTDR-B2 P0084 0084EC-190
EXH TIM SEN/CIR-B1 P1078 1078EC-528
Items
(CONSULT-III screen terms)DTC*
1
Reference page
CONSULT-III
GST*
2ECM*3

INDEX FOR DTC
EC-15
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: 2006 November2007 350ZEXH TIM SEN/CIR-B2 P1084 1084EC-528
EXH/V TIM CONT-B1 P0014 0014EC-160
EXH/V TIM CONT-B2 P0024 0024EC-160
FR/B SOLENOID/CIRC P1757 1757AT- 1 4 7
FTT SEN/CIRCUIT P0182 0182EC-348
FTT SEN/CIRCUIT P0183 0183EC-348
FTT SENSOR P0181 0181EC-344
FUEL LEV SEN SLOSH P0460 0460EC-490
FUEL LEVEL SENSOR P0461 0461EC-492
FUEL LEVL SEN/CIRC P0462 0462EC-494
FUEL LEVL SEN/CIRC P0463 0463EC-494
FUEL SYS-LEAN-B1 P0171 0171EC-324
FUEL SYS-LEAN-B2 P0174 0174EC-324
FUEL SYS-RICH-B1 P0172 0172EC-334
FUEL SYS-RICH-B2 P0175 0175EC-334
HLR/C SOL/CIRC P1767 1767AT- 1 5 1
HO2S2 (B1) P0137 0137EC-287
HO2S2 (B1) P0138 0138EC-298
HO2S2 (B1) P0139 0139EC-313
HO2S2 (B2) P0157 0157EC-287
HO2S2 (B2) P0158 0158EC-298
HO2S2 (B2) P0159 0159EC-313
HO2S2 HTR (B1) P0037 0037EC-173
HO2S2 HTR (B1) P0038 0038EC-173
HO2S2 HTR (B2) P0057 0057EC-173
HO2S2 HTR (B2) P0058 0058EC-173
I/C SOLENOID/CIRC P1752 1752AT- 1 4 5
IAT SEN/CIRCUIT-B1 P0112 0112EC-218
IAT SEN/CIRCUIT-B1 P0113 0113EC-218
IAT SENSOR-B1 P0127 0127EC-243
IN PULY SPEED P1715 1715EC-627
INT/V TIM CONT-B1 P0011 0011EC-156
INT/V TIM CONT-B2 P0021 0021EC-156
INT/V TIM V/CIR-B1 P0075 0075EC-183
INT/V TIM V/CIR-B2 P0081 0081EC-183
ISC SYSTEM P0506 0506EC-498
ISC SYSTEM P0507 0507EC-500
KNOCK SEN/CIRC-B1 P0327 0327EC-379
KNOCK SEN/CIRC-B1 P0328 0328EC-379
KNOCK SEN/CIRC-B2 P0332 0332EC-379
KNOCK SEN/CIRC-B2 P0333 0333EC-379
L/PRESS SOL/CIRC P0745 0745AT- 1 2 9
Items
(CONSULT-III screen terms)DTC*
1
Reference page
CONSULT-III
GST*
2ECM*3

EC-16
INDEX FOR DTC
Revision: 2006 November2007 350Z
*1: 1st trip DTC No. is the same as DTC No.LC/B SOLENOID FNCT P1774 1774AT-155
LC/B SOLENOID/CIRC P1772 1772AT-153
MAF SEN/CIRCUIT-B1 P0101 0101EC-197
MAF SEN/CIRCUIT-B1 P0102 0102EC-208
MAF SEN/CIRCUIT-B1 P0103 0103EC-208
MAF SEN/CIRCUIT-B2 P010B 010BEC-197
MAF SEN/CIRCUIT-B2 P010C 010CEC-208
MAF SEN/CIRCUIT-B2 P010D 010DEC-208
MULTI CYL MISFIRE P0300 0300EC-371
NATS MALFUNCTION P1610 - P1615 1610 - 1615EC-46
NO DTC IS DETECTED.
FURTHER TESTING
MAY BE REQUIRED.P0000 0000 —
P-N POS SW/CIRCUIT P0850 0850EC-520
PNP SW/CIRC P0705 0705AT-102
PURG VOLUME CONT/V P0443 0443EC-423
PURG VOLUME CONT/V P0444 0444EC-431
PURG VOLUME CONT/V P0445 0445EC-431
PW ST P SEN/CIRC P0550 0550EC-502
SENSOR POWER/CIRC P0643 0643EC-514
TCC SOLENOID/CIRC P0740 0740AT-125
TCM P0700 0700AT-101
TCS C/U FUNCTN P1211 1211EC-541
TCS/CIRC P1212 1212EC-542
THERMSTAT FNCTN P0128 0128EC-246
TP SEN 1/CIRC-B1 P0222 0222EC-361
TP SEN 1/CIRC-B1 P0223 0223EC-361
TP SEN 1/CIRC-B2 P2132 2132EC-361
TP SEN 1/CIRC-B2 P2133 2133EC-361
TP SEN 2/CIRC-B1 P0122 0122EC-229
TP SEN 2/CIRC-B1 P0123 0123EC-229
TP SEN 2/CIRC-B2 P0227 0227EC-229
TP SEN 2/CIRC-B2 P0228 0228EC-229
TP SENSOR-B1 P2135 2135EC-582
TP SENSOR-B2 P1239 1239EC-582
TURBINE SENSOR P0717 0717AT- 11 3
TW CATALYST SYS-B1 P0420 0420EC-406
TW CATALYST SYS-B2 P0430 0430EC-406
VEH SPD SEN/CIR AT P0720 0720AT-108
VEH SPEED SEN/CIRC P0500 0500EC-496
VENT CONTROL VALVE P0447 0447EC-437
VENT CONTROL VALVE P0448 0448EC-444
Items
(CONSULT-III screen terms)DTC*
1
Reference page
CONSULT-III
GST*
2ECM*3

EC-18
PRECAUTIONS
Revision: 2006 November2007 350Z
PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
NBS00029
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for Battery ServiceNBS0002A
Before disconnecting the battery, lower both the driver and passenger windows. This will prevent any interfer-
ence between the window edge and the vehicle when the door is opened/closed. During normal operation, the
window slightly raises and lowers automatically to prevent any window to vehicle interference. The automatic
window function will not work with the battery disconnected.
Precautions for Procedures without Cowl Top CoverNBS006TI
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc.
On Board Diagnostic (OBD) System of Engine and A/TNBS0002B
The ECM has an on board diagnostic system. It will light up the malfunction indicator lamp (MIL) to warn the
driver of a malfunction causing emission deterioration.
CAUTION:

Be sure to turn the ignition switch OFF and disconnect the negative battery cable before any
repair or inspection work. The open/short circuit of related switches, sensors, solenoid valves,
etc. will cause the MIL to light up.

Be sure to connect and lock the connectors securely after work. A loose (unlocked) connector will
cause the MIL to light up due to the open circuit. (Be sure the connector is free from water, grease,
dirt, bent terminals, etc.)

Certain systems and components, especially those related to OBD, may use a new style slide-
locking type harness connector. For description and how to disconnect, refer to PG-76, "
HAR-
NESS CONNECTOR" .

Be sure to route and secure the harnesses properly after work. The interference of the harness
with a bracket, etc. may cause the MIL to light up due to the short circuit.
PIIB3706J

EC-20
PRECAUTIONS
Revision: 2006 November2007 350Z

Keep engine control system harness at least 10 cm (4 in) away from adjacent harness, to prevent
engine control system malfunctions due to receiving external noise, degraded operation of ICs,
etc.

Keep engine control system parts and harness dry.

Before replacing ECM, perform ECM Terminals and Refer-
ence Value inspection and make sure ECM functions prop-
erly. Refer to EC-103, "
ECM Terminals and Reference Value"
.

Handle mass air flow sensor carefully to avoid damage.

Do not clean mass air flow sensor with any type of deter-
gent.

Do not disassemble electric throttle control actuator.

Even a slight leak in the air intake system can cause seri-
ous incidents.

Do not shock or jar the camshaft position sensor (PHASE),
crankshaft position sensor (POS).

After performing each TROUBLE DIAGNOSIS, perform DTC
Confirmation Procedure or Overall Function Check.
The DTC should not be displayed in the DTC Confirmation
Procedure if the repair is completed. The Overall Function
Check should be a good result if the repair is completed.

When measuring ECM signals with a circuit tester, never
allow the two tester probes to contact.
Accidental contact of probes will cause a short circuit and
damage the ECM power transistor.

Do not use ECM ground terminals when measuring input/
output voltage. Doing so may result in damage to the ECM's
transistor. Use a ground other than ECM terminals, such as
the ground.
MEF040D
SEF217U
SEF348N

PRECAUTIONS
EC-21
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: 2006 November2007 350Z

B1 indicates the bank 1, B2 indicates the bank 2 as shown
in the figure.

Do not operate fuel pump when there is no fuel in lines.

Tighten fuel hose clamps to the specified torque.

Do not depress accelerator pedal when starting.

Immediately after starting, do not rev up engine unneces-
sarily.

Do not rev up engine just prior to shutdown.

When installing C.B. ham radio or a mobile phone, be sure
to observe the following as it may adversely affect elec-
tronic control systems depending on installation location.
–Keep the antenna as far as possible from the electronic
control units.
–Keep the antenna feeder line more than 20 cm (8 in) away
from the harness of electronic controls.
Do not let them run parallel for a long distance.
–Adjust the antenna and feeder line so that the standing-
wave radio can be kept smaller.
–Be sure to ground the radio to vehicle body.
SEC893C
1 : Fuel level sensor unit and fuel pump
2 : Fuel pressure regulator
3 : Fuel tank temperature sensor
PBIB2707E
SEF709Y
SEF708Y

EC-22
PREPARATION
Revision: 2006 November2007 350Z
PREPARATIONPFP:00002
Special Service ToolsNBS0002E
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool nameDescription
KV10117100
(J-36471-A)
Heated oxygen
sensor wrenchLoosening or tightening heated oxygen sensor
with 22 mm (0.87 in) hexagon nut
KV10114400
(J-38365)
Heated oxygen
sensor wrenchLoosening or tightening heated oxygen sensor
a: 22 mm (0.87 in)
(J-44626)
Air fuel ratio (A/F)
sensor wrenchLoosening or tightening air fuel ratio (A/F) sensor
1
(J-44321)
Fuel pressure gauge
kitChecking fuel pressure
S-NT379
S-NT636
LEM054
LEC642

PREPARATION
EC-23
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: 2006 November2007 350Z
Commercial Service ToolsNBS0002F
Tool name
(Kent-Moore No.)Description
Leak detector
i.e.: (J-41416)Locating the EVAP leak
EVAP service port
adapter
i.e.: (J-41413-OBD)Applying positive pressure through EVAP service
port
Fuel filler cap adapter
i.e.: (MLR-8382)Checking fuel tank vacuum relief valve opening
pressure
Socket wrench Removing and installing engine coolant
temperature sensor
Oxygen sensor thread
cleaner
i.e.: (J-43897-18)
(J-43897-12)Reconditioning the exhaust system threads
before installing a new oxygen sensor. Use with
anti-seize lubricant shown below.
a: 18 mm diameter with pitch 1.5 mm for
Zirconia Oxygen Sensor
b: 12 mm diameter with pitch 1.25 mm for
Titania Oxygen Sensor
Anti-seize lubricant
i.e.: (Permatex
TM
133AR or equivalent
meeting MIL
specification MIL-A-
907)Lubricating oxygen sensor thread cleaning tool
when reconditioning exhaust system threads.
S-NT703
S-NT704
S-NT815
S-NT705
AEM488
S-NT779