dtc NISSAN ALMERA N16 2003 Electronic Repair Manual

SGI862-A
DETECTABLE LINES AND NON-DETECTABLE LINESNJGI0003S0205In some wiring diagrams, two kinds of lines, representing wires,
with different weight are used.
A line with regular weight (wider line) represents a “detectable
line for DTC (Diagnostic Trouble Code)”. A “detectable line for
DTC” is a circuit in which ECM can detect its malfunctions with
the on board diagnostic system.
A line with less weight (thinner line) represents a “non-detect-
able line for DTC”. A “non-detectable line for DTC” is a circuit
in which ECM cannot detect its malfunctions with the on board
diagnostic system.
HOW TO READ WIRING DIAGRAMS
Description (Cont’d)
GI-18

NJGI0007
Function and System ApplicationNJGI0007S05
Diagnostic
test modeFunction ENGINE A/T ABS AIR BAGSMART
EN-
TRANCENATS*1NAVIGA-
TION
Work sup-
portThis mode enables a technician to
adjust some devices faster and
more accurate by following the indi-
cations on CONSULT-II.x ———X——
Self-diag-
nostic
resultsSelf-diagnostic results can be read
anderasedquickly. x x x x—x—
Trouble
diagnostic
recordCurrent self-diagnostic results and
all trouble diagnostic records previ-
ously stored can be read.——— x ———
ECU dis-
criminated
No.Classification number of a replace-
ment ECU can be read to prevent
an incorrect ECU from being
installed.——— x ———
Data monitorInput/Output data in the ECU
(ECM) can be read.x x x—x——
Data monitor
(Spec.)The specified values will be dis-
played when an OK/NG judgement
is difficult for the DATA MONITOR
items by Barchart and Line Graph.X ——————
DTC work
supportThis mode enables a technician to
set operating conditions to confirm
self-diagnoses status/results.x*2x —————
Active testDiagnostic Test Mode in which
CONSULT-II drives some actuators
apart from the ECMs and also
shifts some parameters in a speci-
fied range.x—x—x——
ECU (ECM)
part numberECU (ECM) part number can be
read.x x x ————
Control unit
initializationAll registered ignition key IDs in
NATS components can be initial-
ized and new IDs can be regis-
tered.————— x —
PIN
INITIALIZA-
TIONNavigation system will be locked
when the vehicle’s owner enters
the wrong PIN five consecutive
times.
To release the lock, use “PIN INI-
TIALIZATION”.—————— x
NAVI ID
INITIALIZA-
TIONIn nomal times regulation codes are
being communicated between Navi-
gation Control Unit and Dongle
Control Unit.
Use “NAVI ID INITIALIZATION” to
match the codes when either one
has been replaced due to break-
down or etc.—————— x
x: Applicable
*1: NATS (Nissan Anti-Theft System)
*2: For models with Euro-OBD system
CONSULT-II CHECKING SYSTEM
Function and System Application
GI-36

NJGI0011
ISO 15031-2NJGI0011S01All emission related terms used in this publication in accordance with ISO15031-2 are listed. Accordingly, new
terms, new acronyms/abbreviations and old terms are listed in the following chart.
***: Not applicable
NEW TERMNEW ACRONYM /
ABBREVIATIONOLD TERM
Air cleaner ACL Air cleaner
Barometric pressure sensor BARO sensor ***
Barometric pressure sensor-BCDD BAROS-BCDD BCDD
Camshaft position CMP ***
Camshaft position sensor CMPS Crank angle sensor
Canister *** Canister
Carburetor CARB Carburetor
Charge air cooler CAC Intercooler
Closed loop CL Closed loop
Closed throttle position switch CTP switch Idle switch
Clutch pedal position switch CPP switch Clutch switch
Continuous fuel injection system CFI system ***
Continuous trap oxidizer system CTOX system ***
Crankshaft position CKP ***
Crankshaft position sensor CKPS ***
Data link connector DLC Diagnostic connector for CONSULT
Diagnostic test mode DTM Diagnostic mode
Diagnostic test mode selector DTM selector Diagnostic mode selector
Diagnostic test mode I DTM I Mode I
Diagnostic test mode II DTM II Mode II
Diagnostic trouble code DTC Malfunction code
Direct fuel injection system DFI system ***
Distributor ignition system DI system Ignition timing control
Early fuel evaporation-mixture heater EFE-mixture heater Mixture heater
Early fuel evaporation system EFE system Mixture heater control
Electrically erasable programmable read
only memoryEEPROM ***
Electronic ignition system EI system Ignition timing control
Engine control EC ***
Engine control module ECM ECCS control unit
Engine coolant temperature ECT Engine temperature
Engine coolant temperature sensor ECTS Engine temperature sensor
Engine modification EM ***
Engine speed RPM Engine speedMA
EM
LC
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
ISO 15031-2 TERMINOLOGY LIST
ISO 15031-2
GI-51

Cooling FanNJLC0026COMPONENTSNJLC0026S01
YLC023
CONTROL SYSTEMNJLC0026S02Cooling fans are controlled by the ECM. For details, refer to
EC-324 or EC-596, “DTC P1217 ENGINE OVER
TEMPERATURE”.
Changing Engine CoolantNJLC0037WARNING:
To avoid the danger of being scalded, never change the cool-
ant when the engine is hot.
— DRAINING ENGINE COOLANT —NJLC0037S011. Set air conditioning system as follows to prevent coolant from
remaining in the system.
a. Turn ignition switch ON and set temperature controller to maxi-
mum hot position.
b. Wait 10 seconds before turning ignition switch OFF.
GI
MA
EM
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
ENGINE COOLING SYSTEMQG
Cooling Fan
LC-17

REMOVAL AND INSTALLATION=NJLC00631. Remove under cover.
2. Drain coolant by removing lower radiator hose.
3. Disconnect radiator upper and lower hoses.
4. Remove radiator shroud.
5. Disconnect reservoir tank hose.
6. Remove radiator mounting bracket.
7. Remove radiator.
8. After repairing or replacing radiator, install any part removed in
reverse order of removal.
When filling radiator with coolant, refer to LC-43, “Changing
Engine Coolant”.
Cooling FanNJLC0064COMPONENTSNJLC0064S01
JLC347B
CONTROL SYSTEMNJLC0064S02Cooling fans are controlled by ECM. For details, refer to EC-130,
“DTC P1217 OVER HEAT”.
ENGINE COOLING SYSTEMYD
Radiator (Cont’d)
LC-42

EC-1
ENGINE CONTROL SYSTEM
B ENGINE
CONTENTS
C
D
E
F
G
H
I
J
K
L
M
SECTION
A
EC
ENGINE CONTROL SYSTEM
QG (WITH EURO-OBD)
INDEX FOR DTC ...................................................... 10
Alphabetical Index .................................................. 10
DTC No. Index ....................................................... 12
PRECAUTIONS ........................................................ 15
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ................................................................ 15
On Board Diagnostic (OBD) System of Engine and
A/T .......................................................................... 15
Precaution .............................................................. 15
Wiring Diagrams and Trouble Diagnosis ................ 18
PREPARATION ......................................................... 19
Special Service Tools ............................................. 19
Commercial Service Tools ...................................... 19
ENGINE CONTROL SYSTEM .................................. 21
System Diagram ..................................................... 21
Vacuum Hose Drawing ........................................... 22
System Chart ......................................................... 23
Multiport Fuel Injection (MFI) System .................... 23
Electronic Ignition (EI) System ............................... 25
Air Conditioning Cut Control ................................... 26
Fuel Cut Control (at No Load and High Engine
Speed) .................................................................... 27
CAN Communication .............................................. 27
BASIC SERVICE PROCEDURE .............................. 30
Idle Speed and Ignition Timing Check .................... 30
Accelerator Pedal Released Position Learning ...... 31
Throttle Valve Closed Position Learning ................ 31
Idle Air Volume Learning ........................................ 31
Fuel Pressure Check .............................................. 34
ON BOARD DIAGNOSTIC (OBD) SYSTEM ............ 36
Introduction ............................................................ 36
Two Trip Detection Logic ........................................ 36
Emission-related Diagnostic Information ................ 37
NATS (Nissan Anti-theft System) ........................... 49
Malfunction Indicator (MI) ....................................... 49
OBD System Operation Chart ................................ 52
TROUBLE DIAGNOSIS ............................................ 58
Trouble Diagnosis Introduction ............................... 58DTC Inspection Priority Chart ................................. 62
Fail-safe Chart ........................................................ 63
Basic Inspection ..................................................... 65
Symptom Matrix Chart ............................................ 70
Engine Control Component Parts Location ............ 74
Circuit Diagram ....................................................... 78
ECM Harness Connector Terminal Layout ............. 80
ECM Terminals and Reference Value ..................
... 80
CONSULT-II Function ............................................. 87
Generic Scan Tool (GST) Function ......................... 97
CONSULT-II Reference Value in Data Monitor Mode
... 99
Major Sensor Reference Graph in Data Monitor
Mode .....................................................................102
TROUBLE DIAGNOSIS - SPECIFICATION VALUE .105
Description ............................................................105
Testing Condition ..................................................105
Inspection Procedure ............................................105
Diagnostic Procedure ...........................................106
TROUBLE DIAGNOSIS FOR INTERMITTENT INCI-
DENT .......................................................................109
Description ............................................................109
Diagnostic Procedure ...........................................109
POWER SUPPLY CIRCUIT FOR ECM ...................110
Wiring Diagram .....................................................110
Diagnostic Procedure ............................................111
Component Inspection ..........................................115
DTC U1000, U1001 CAN COMMUNICATION LINE .116
Description ............................................................116
On Board Diagnosis Logic ....................................116
DTC Confirmation Procedure ...............................116
Wiring Diagram .....................................................117
Diagnostic Procedure ...........................................118
DTC P0011 IVT CONTROL .....................................119
Description ............................................................119
CONSULT-II Reference Value in Data Monitor Mode
.119
On Board Diagnosis Logic ....................................120
DTC Confirmation Procedure ...............................120
Diagnostic Procedure ...........................................121

EC-2
DTC P0031, P0032 HO2S1 HEATER .....................122
Description ............................................................122
CONSULT-II Reference Value in Data Monitor Mode
.122
On Board Diagnosis Logic ....................................122
DTC Confirmation Procedure ...............................122
Wiring Diagram .....................................................124
Diagnostic Procedure ...........................................125
Component Inspection ..........................................127
Removal and Installation ......................................127
DTC P0037, P0038 HO2S2 HEATER .....................128
Description ............................................................128
CONSULT-II Reference Value in Data Monitor Mode
.128
On Board Diagnosis Logic ....................................128
DTC Confirmation Procedure ...............................128
Wiring Diagram .....................................................130
Diagnostic Procedure ...........................................131
Component Inspection ..........................................133
Removal and Installation ......................................133
DTC P0102, P0103 MAF SENSOR .........................134
Component Description ........................................134
CONSULT-II Reference Value in Data Monitor Mode
.134
On Board Diagnosis Logic ....................................134
DTC Confirmation Procedure ...............................135
Wiring Diagram .....................................................136
Diagnostic Procedure ...........................................137
Component Inspection ..........................................139
Removal and Installation ......................................139
DTC P0112, P0113 IAT SENSOR ...........................140
Component Description ........................................140
On Board Diagnosis Logic ....................................140
DTC Confirmation Procedure ...............................140
Wiring Diagram .....................................................141
Diagnostic Procedure ...........................................142
Component Inspection ..........................................143
Removal and Installation ......................................143
DTC P0117, P0118 ECT SENSOR ..........................144
Component Description ........................................144
On Board Diagnosis Logic ....................................144
DTC Confirmation Procedure ...............................145
Wiring Diagram .....................................................146
Diagnostic Procedure ...........................................147
Component Inspection ..........................................148
Removal and Installation ......................................148
DTC P0132 HO2S1 .................................................149
Component Description ........................................149
CONSULT-II Reference Value in Data Monitor Mode
.149
On Board Diagnosis Logic ...................................
.149
DTC Confirmation Procedure ...............................150
Wiring Diagram .....................................................151
Diagnostic Procedure ...........................................152
Component Inspection ..........................................153
Removal and Installation ......................................154
DTC P0133 HO2S1 .................................................155
Component Description ........................................155
CONSULT-II Reference Value in Data Monitor Mode .155
On Board Diagnosis Logic ....................................155
DTC Confirmation Procedure ................................156
Overall Function Check .........................................157
Wiring Diagram .....................................................158
Diagnostic Procedure ............................................159
Component Inspection ..........................................162
Removal and Installation .......................................164
DTC P0134 HO2S1 ................................................ .165
Component Description ........................................165
CONSULT-II Reference Value in Data Monitor Mode
.165
On Board Diagnosis Logic ....................................165
DTC Confirmation Procedure ................................166
Overall Function Check .........................................166
Wiring Diagram .....................................................168
Diagnostic Procedure ............................................169
Component Inspection ..........................................170
Removal and Installation .......................................171
DTC P0138 HO2S2 ................................................ .172
Component Description ........................................172
CONSULT-II Reference Value in Data Monitor Mode
.172
On Board Diagnosis Logic ....................................172
DTC Confirmation Procedure ................................173
Wiring Diagram .....................................................174
Diagnostic Procedure ............................................175
Component Inspection ..........................................176
Removal and Installation .......................................177
DTC P0139 HO2S2 ................................................ .178
Component Description ........................................178
CONSULT-II Reference Value in Data Monitor Mode
.178
On Board Diagnosis Logic ....................................178
DTC Confirmation Procedure ................................179
Overall Function Check .........................................180
Wiring Diagram .....................................................181
Diagnostic Procedure ............................................182
Component Inspection ..........................................184
Removal and Installation ......................................
.185
DTC P0171 FUEL INJECTION SYSTEM FUNCTION .186
On Board Diagnosis Logic ....................................186
DTC Confirmation Procedure ................................186
Wiring Diagram .....................................................188
Diagnostic Procedure ............................................189
DTC P0172 FUEL INJECTION SYSTEM FUNCTION .193
On Board Diagnosis Logic ....................................193
DTC Confirmation Procedure ................................193
Wiring Diagram .....................................................195
Diagnostic Procedure ............................................196
DTC P0221 TP SENSOR ........................................199
Component Description ........................................199
CONSULT-II Reference Value in Data Monitor Mode
.199
On Board Diagnosis Logic ....................................199
DTC Confirmation Procedure ................................199
Wiring Diagram .....................................................201
Diagnostic Procedure ............................................202

EC-3
C
D
E
F
G
H
I
J
K
L
M
ECA Component Inspection ......................................... 204
Removal and Installation ...................................... 204
DTC P0222, P0223 TP SENSOR ........................... 205
Component Description ........................................ 205
CONSULT-II Reference Value in Data Monitor Mode
. 205
On Board Diagnosis Logic ................................... 205
DTC Confirmation Procedure ............................... 205
Wiring Diagram .................................................... 207
Diagnostic Procedure ........................................... 208
Component Inspection ......................................... 210
Removal and Installation ...................................... 210
DTC P0226 APP SENSOR ......................................211
Component Description ......................................... 211
CONSULT-II Reference Value in Data Monitor Mode
.. 211
On Board Diagnosis Logic .................................... 211
DTC Confirmation Procedure ................................ 211
Wiring Diagram .................................................... 213
Diagnostic Procedure ........................................... 214
Component Inspection ......................................... 216
Removal and Installation ...................................... 217
DTC P0227, P0228 APP SENSOR ........................ 218
Component Description ........................................ 218
CONSULT-II Reference Value in Data Monitor Mode
. 218
On Board Diagnosis Logic ................................... 218
DTC Confirmation Procedure ............................... 218
Wiring Diagram .................................................... 220
Diagnostic Procedure ........................................... 221
Component Inspection ......................................... 223
Removal and Installation ...................................... 224
DTC P0300 - P0304 MULTIPLE CYLINDER MIS-
FIRE, NO. 1 - 4 CYLINDER MISFIRE ..................... 225
On Board Diagnosis Logic ................................... 225
DTC Confirmation Procedure ............................... 225
Diagnostic Procedure ........................................... 226
DTC P0327, P0328 KS ........................................... 230
Component Description ........................................ 230
On Board Diagnosis Logic ................................... 230
DTC Confirmation Procedure ............................... 230
Wiring Diagram .................................................... 231
Diagnostic Procedure ........................................... 232
Component Inspection ......................................... 233
Removal and Installation ...................................... 233
DTC P0335 CKP SENSOR (POS) .......................... 234
Component Description ........................................ 234
CONSULT-II Reference Value in Data Monitor Mode
. 234
On Board Diagnosis Logic ................................... 234
DTC Confirmation Procedure ............................... 234
Wiring Diagram ...................................................
. 235
Diagnostic Procedure ........................................... 236
Component Inspection ......................................... 238
Removal and Installation ...................................... 239
DTC P0340 CMP SENSOR (PHASE) ..................... 240
Component Description ........................................ 240
On Board Diagnosis Logic ................................... 240
DTC Confirmation Procedure ............................... 240Wiring Diagram .....................................................241
Diagnostic Procedure ...........................................242
Component Inspection ..........................................244
Removal and Installation ......................................245
DTC P0420 THREE WAY CATALYST FUNCTION . 246
On Board Diagnosis Logic ....................................246
DTC Confirmation Procedure ...............................246
Overall Function Check ........................................247
Diagnostic Procedure ...........................................248
DTC P0444 EVAP CANISTER PURGE VOLUME
CONTROL SOLENOID VALVE ...............................251
Description ............................................................251
CONSULT-II Reference Value in Data Monitor Mode
.251
On Board Diagnosis Logic ....................................252
DTC Confirmation Procedure ...............................252
Wiring Diagram .....................................................253
Diagnostic Procedure ...........................................254
Component Inspection ..........................................256
Removal and Installation ......................................256
DTC P0500 VSS ......................................................257
Description ............................................................257
On Board Diagnosis Logic ....................................257
DTC Confirmation Procedure ...............................257
Overall Function Check ........................................258
Diagnostic Procedure ...........................................259
DTC P0550 PSP SENSOR .....................................260
Component Description ........................................260
CONSULT-II Reference Value in Data Monitor Mode
.260
On Board Diagnosis Logic ....................................260
DTC Confirmation Procedure ...............................260
Wiring Diagram .....................................................261
Diagnostic Procedure ...........................................262
Component Inspection ..........................................264
DTC P0605 ECM .....................................................265
Component Description ........................................265
On Board Diagnosis Logic ....................................265
DTC Confirmation Procedure ...............................265
Diagnostic Procedure ...........................................266
DTC P1065 ECM POWER SUPPLY .......................268
Component Description ........................................268
On Board Diagnosis Logic ....................................268
DTC Confirmation Procedure ...............................268
Wiring Diagram .....................................................269
Diagnostic Procedure ...........................................270
DTC P1111 IVT CONTROL SOLENOID VALVE .....272
Component Description ........................................272
CONSULT-II Reference Value in Data Monitor Mode
.272
On Board Diagnosis Logic ....................................272
DTC Confirmation Procedure ...............................272
Wiring Diagram .....................................................273
Diagnostic Procedure ...........................................274
Component Inspection ..........................................275
Removal and Installation ......................................275
DTC P1121 ELECTRIC THROTTLE CONTROL
ACTUATOR .............................................................276
Component Description ........................................276

EC-4
On Board Diagnosis Logic ....................................276
DTC Confirmation Procedure ...............................276
Diagnostic Procedure ...........................................277
Removal and Installation ......................................277
DTC P1122 ELECTRIC THROTTLE CONTROL
FUNCTION ..............................................................278
Description ............................................................278
On Board Diagnosis Logic ....................................278
DTC Confirmation Procedure ...............................278
Wiring Diagram .....................................................279
Diagnostic Procedure ...........................................280
Component Inspection ..........................................284
Removal and Installation ......................................284
DTC P1124, P1126 THROTTLE CONTROL MOTOR
RELAY .....................................................................285
Component Description ........................................285
CONSULT-II Reference Value in Data Monitor Mode
.285
On Board Diagnosis Logic ....................................285
DTC Confirmation Procedure ...............................285
Wiring Diagram .....................................................287
Diagnostic Procedure ...........................................288
Component Inspection ..........................................289
DTC P1128 THROTTLE CONTROL MOTOR .........291
Component Description ........................................291
On Board Diagnosis Logic ....................................291
DTC Confirmation Procedure ...............................291
Wiring Diagram .....................................................292
Diagnostic Procedure ...........................................293
Component Inspection ..........................................294
Removal and Installation ......................................295
DTC P1143 HO2S1 .................................................296
Component Description ........................................296
CONSULT-II Reference Value in Data Monitor Mode
.296
On Board Diagnosis Logic ....................................296
DTC Confirmation Procedure ...............................297
Overall Function Check ........................................298
Diagnostic Procedure ...........................................298
Component Inspection ..........................................300
Removal and Installation ......................................301
DTC P1144 HO2S1 .................................................302
Component Description ........................................302
CONSULT-II Reference Value in Data Monitor Mode
.302
On Board Diagnosis Logic ....................................302
DTC Confirmation Procedure ...............................303
Overall Function Check ........................................304
Diagnostic Procedure ...........................................304
Component Inspection ..........................................306
Removal and Installation ......................................307
DTC P1146 HO2S2 ...............................................
..308
Component Description ........................................308
CONSULT-II Reference Value in Data Monitor Mode
.308
On Board Diagnosis Logic ....................................308
DTC Confirmation Procedure ...............................308
Overall Function Check ........................................310
Wiring Diagram .....................................................311Diagnostic Procedure ............................................312
Component Inspection ..........................................314
Removal and Installation .......................................315
DTC P1147 HO2S2 ..................................................316
Component Description ........................................316
CONSULT-II Reference Value in Data Monitor Mode
.316
On Board Diagnosis Logic ....................................316
DTC Confirmation Procedure ................................317
Overall Function Check .........................................318
Wiring Diagram .....................................................319
Diagnostic Procedure ............................................320
Component Inspection ..........................................322
Removal and Installation .......................................323
DTC P1217 ENGINE OVER TEMPERATURE ........324
System Description ...............................................324
CONSULT-II Reference Value in Data Monitor Mode
.324
On Board Diagnosis Logic ....................................325
Overall Function Check .........................................325
Wiring Diagram .....................................................327
Diagnostic Procedure ............................................328
Main 12 Causes of Overheating ...........................333
Component Inspection ..........................................334
DTC P1223, P1224 TP SENSOR ............................335
Component Description ........................................335
CONSULT-II Reference Value in Data Monitor Mode
.335
On Board Diagnosis Logic ....................................335
DTC Confirmation Procedure ................................335
Wiring Diagram .....................................................337
Diagnostic Procedure ............................................338
Component Inspection ..........................................340
Removal and Installation .......................................340
DTC P1225 TP SENSOR ........................................341
Component Description ........................................341
On Board Diagnosis Logic ....................................341
DTC Confirmation Procedure ................................341
Diagnostic Procedure ............................................342
Removal and Installation .......................................342
DTC P1226 TP SENSOR ........................................343
Component Description ........................................343
On Board Diagnosis Logic ....................................343
DTC Confirmation Procedure ................................343
Diagnostic Procedure ............................................344
Removal and Installation .......................................344
DTC P1227, P1228 APP SENSOR .........................345
Component Description ........................................345
CONSULT-II Reference Value in Data Monitor Mode
.345
On Board Diagnosis Logic ....................................345
DTC Confirmation Procedure ................................345
Wiring Diagram .....................................................347
Diagnostic Procedure ............................................348
Component Inspection ..........................................350
Removal and Installation .......................................351
DTC P1229 SENSOR POWER SUPPLY ................352
On Board Diagnosis Logic ....................................352
DTC Confirmation Procedure ................................352

EC-5
C
D
E
F
G
H
I
J
K
L
M
ECA Wiring Diagram .................................................... 353
Diagnostic Procedure ........................................... 354
DTC P1706 PNP SWITCH ...................................... 356
Component Description ........................................ 356
CONSULT-II Reference Value in Data Monitor Mode
. 356
On Board Diagnosis Logic ................................... 356
DTC Confirmation Procedure ............................... 356
Overall Function Check ........................................ 357
Wiring Diagram .................................................... 358
Diagnostic Procedure ........................................... 359
DTC P1805 BRAKE SWITCH ................................ 360
Description ........................................................... 360
CONSULT-II Reference Value in Data Monitor Mode
. 360
On Board Diagnosis Logic ................................... 360
DTC Confirmation Procedure ............................... 360
Wiring Diagram .................................................... 361
Diagnostic Procedure ........................................... 362
Component Inspection ......................................... 364
IGNITION SIGNAL .................................................. 365
Component Description ........................................ 365
Wiring Diagram .................................................... 366
Diagnostic Procedure ........................................... 369
Component Inspection ......................................... 373
Removal and Installation ...................................... 374
INJECTOR CIRCUIT ............................................... 375
Component Description ........................................ 375
CONSULT-II Reference Value in Data Monitor Mode
. 375
Wiring Diagram .................................................... 376
Diagnostic Procedure ........................................... 377
Component Inspection ......................................... 380
Removal and Installation ...................................... 380
FUEL PUMP CIRCUIT ............................................ 381
Description ........................................................... 381
CONSULT-II Reference Value in Data Monitor Mode
. 381
Wiring Diagram .................................................... 382
Diagnostic Procedure ........................................... 383
Component Inspection ......................................... 385
Removal and Installation ...................................... 386
REFRIGERANT PRESSURE SENSOR ................. 387
Component Description ........................................ 387
Wiring Diagram .................................................... 388
Diagnostic Procedure ........................................... 389
Removal and Installation ...................................... 391
ELECTRICAL LOAD SIGNAL ................................ 392
Description ...................................................
........ 392
CONSULT-II Reference Value in Data Monitor Mode
. 392
Wiring Diagram .................................................... 393
Diagnostic Procedure ........................................... 394
MI & DATA LINK CONNECTORS .......................... 397
Wiring Diagram—LHD Models ............................. 397
Wiring Diagram—RHD Models ............................ 398
EVAPORATIVE EMISSION SYSTEM ..................... 399
Description ........................................................... 399
Component Inspection ......................................... 401POSITIVE CRANKCASE VENTILATION ...............402
Description ............................................................402
Component Inspection ..........................................402
SERVICE DATA AND SPECIFICATIONS (SDS) ....404
Fuel Pressure .......................................................404
Idle Speed and Ignition Timing .............................404
Calculated Load Value ..........................................404
Mass Air Flow Sensor ...........................................404
Intake Air Temperature Sensor .............................404
Engine Coolant Temperature Sensor ...................404
Heated Oxygen Sensor 1 Heater .........................404
Heated Oxygen sensor 2 Heater ..........................404
Crankshaft Position Sensor (POS) .......................404
Camshaft Position Sensor (PHASE) ....................404
Throttle Control Motor ...........................................405
Injector ..................................................................405
Fuel Pump ............................................................405
QG (WITHOUT EURO-OBD)
INDEX FOR DTC .....................................................406
Alphabetical Index ................................................406
DTC No. Index ......................................................407
PRECAUTIONS ......................................................409
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ...............................................................409
On Board Diagnostic (OBD) System of Engine ....409
Precaution ............................................................409
Wiring Diagrams and Trouble Diagnosis ..............412
PREPARATION .......................................................413
Special Service Tools ...........................................413
Commercial Service Tools ....................................413
ENGINE CONTROL SYSTEM ................................415
System Diagram ...................................................415
Vacuum Hose Drawing .........................................416
System Chart ........................................................417
Multiport Fuel Injection (MFI) System ...................417
Electronic Ignition (EI) System .............................419
Air Conditioning Cut Control .................................420
Fuel Cut Control (at No Load and High Engine
Speed) ..................................................................421
CAN Communication ............................................421
BASIC SERVICE PROCEDURE .............................424
Idle Speed and Ignition Timing Check ..................424
Accelerator Pedal Released Position Learning ....425
Throttle Valve Closed Position Learning ...............425
Idle Air Volume Learning ......................................425
Fuel Pressure Check ............................................427
ON BOARD DIAGNOSTIC (OBD) SYSTEM ..........429
Introduction ...........................................................429
Two Trip Detection Logic ......................................429
Emission-related Diagnostic Information ..............429
NATS (Nissan Anti-theft System) .........................431
Malfunction Indicator (MI) .....................................432
TROUBLE DIAGNOSIS ..........................................436
Trouble Diagnosis Introduction .............................436
DTC Inspection Priority Chart ...............................440
Fail-safe Chart ......................................................441