light NISSAN ARMADA 2017 2.G 08IT Navigation Manual

7. Highlight a street as the 2nd street from thelist and push <ENTER>.
8. The entire route is shown on the map.
Highlight [Start] after confirming the location
of the displayed destination, and push
<ENTER>. The system sets the destination
to the selected location and starts calculat-
ing a route.
INFO:
Even after setting a destination, the location of
the destination can be adjusted, the route can
be stored, etc.
“Procedures after setting destination”
(page 5-2)
SETTING CITY CENTER
The system can calculate a route to the center of
a city, without setting a specific location.
1. Push <DEST>.
2. Highlight [Next Page] and push <ENTER>.
3. Highlight [City Center] and push
<ENTER>. A character input screen is
displayed.
4. Enter the name of the city, highlight [List]and push <ENTER>. A list screen is
displayed.
INFO:
Highlight [Last 5 Cities] and push
<ENTER> to display 5 cities recently set
as destinations.
Setting destination4-17

5. Highlight the preferred destination from thelist and push <ENTER>. The position of the
selected location is displayed in the preview
on the right side of the screen.
INFO:
By selecting [By Distance], the list can be
sorted by the nearest distance.
6. The selected destination is displayed at the center of the map. Highlight [Start] after
confirming the location of the displayed
destination, and push <ENTER>. The system sets the destination to the
selected location and starts calculating a
route.
INFO:
Even after setting a destination, the location
of the destination can be adjusted, the route
can be stored, etc.
“Procedures after setting destination”
(page 5-2)
SETTING POINT ON MAP
A location scrolled to on the map can be set as
the destination to which the system calculates a
route.
1. Scroll the map, place the cross pointer over the preferred location, and push <ENTER>.
INFO:
.Adjust the map scale to search for a
location more effectively.
.The point on the blinking road where thecenter of the cross pointer is located can
be set as a destination.
2. Highlight [New Dest.] and push <ENTER>.
INFO:
For the items except for [New Dest.], refer to
“Map menu screen”.
“Scrolled location map screen”
(page 2-16)
4-18Setting destination

After performing a route search, the route
guidance can be started immediately. Also, it is
possible to confirm or change a route.
AVAILABLE ITEMS AFTER SETTING
DESTINATION
.[Start]:
Starts route guidance to the selected
destination.
“Starting route guidance” (page 5-2)
. [More Routes]:
Displays 3 alternative routes.
“Selecting route” (page 5-3)
. [Add/Route Info]:
Displays the route information or add a
destination or a waypoint.
“Confirming route” (page 5-3)
. [Move Location]:
Displays a map screen and allows the
location of the destination to be adjusted.
“Moving location of destination”
(page 5-4)
. [Store Location]:
Stores the location in the Address Book.
“Storing location” (page 5-5)
. [Place Info]:
Displays information about the facility that is
set as the destination if it is included in the
map data.
“Viewing information about searched
location” (page 5-5)
INFO:
. If no operations are performed on the
system for several seconds, [Start] is auto-
matically selected, and the system starts
route guidance.
. When using waypoints, [More Routes] is
disabled. After the route is started, push
<ROUTE> then select [Edit/Add to Route]
to change the route between each waypoint.
“Editing route” (page 5-14)
. The same screen as when [Move Location]
is selected can be displayed with the
following operations:
— Touching the map screen — Pushing the directional buttons except
for the up/down button (multi-function
controller with directional buttons)
— Pushing the slide switch except in the upward/downward direction (multi-func-
tion controller without directional but-
tons)
STARTING ROUTE GUIDANCE
1. Highlight [Start] and push <ENTER>.
Route guidance starts.
PROCEDURES AFTER SETTING
DESTINATION
5-2Route guidance

SELECTING ROUTE
1. Highlight [More Routes] and push<ENTER>.
2. Highlight the preferred route condition andpush <ENTER>.
3. The display automatically returns to the previous screen.
Available route conditions
.[Short. Time] (purple):
Prioritizes by the shortest time. .
[Min. Freeway] (orange):
Minimizes the use of freeways.
. [Short. Dist.] (green):
Prioritizes by the shortest distance.
INFO:
. When a route condition is selected, a
preview is displayed on the right side of
the screen.
. The 3 routes may not always be different.
CONFIRMING ROUTE
1. Highlight [Add/Route Info] and push
<ENTER>.
2. Highlight the preferred information item and push <ENTER>.
3. Push <BACK> to return to the previous
screen.
Available information
. [Turn List]:
Displays the details of the suggested route.
“Using turn list” (page 5-19)
. [Preview]:
The system will trace the planned route
going forward or in reverse.
“Using route preview” (page 5-19)
. [Add Way Pt.]:
Add a waypoint or a destination.
“Adding destination or waypoint”
(page 5-4)
. [Store Route]:
A calculated route can be stored. A max-
imum of 5 routes can be stored. Stored
routes can be easily retrieved and set as the
suggested route.
“Storing route” (page 6-5)
Route guidance5-3

.[Map Scroll]:
Displays a map screen where the location of
the destination can be confirmed.
The same screen as when [Map Scroll] is
touched can be displayed with the following
operations:
— Touching the map screen.
— Pushing the directional buttons except for the up/down button (multi-function
controller with directional buttons) .
— Pushing the slide switch except in the upward/downward direction (multi-func-
tion controller without directional but-
tons) .
Adding destination or waypoint
Before starting route guidance, destinations
and/or waypoints can be added. A total of 6
destinations or waypoints can be set.
1. Highlight [Add Way Pt.] and push <ENTER>.
2. Set additional destinations or waypoints andpush <ENTER>.
The method of searching for a location is the
same as the one for a destination.
“4. Setting destination”
3. Highlight [Add Destination] or [Add Way- point] and push <ENTER>.
4. The system starts calculating a route that
includes the added destination or waypoint.
When the calculation is finished, the route is
displayed.
INFO:
.If a waypoint was added, [More Routes]cannot be selected.
.If a destination was added, the priordestination becomes a waypoint.
MOVING LOCATION OF DESTINATION
The location of the destination can be adjusted
by moving the cross pointer across the map.
5-4Route guidance

1. Highlight [Move Location] and push<ENTER>.
INFO:
The screen for adjusting the location also
changes by touching the map screen dis-
played on the right side of the screen.
2. Adjust the location by moving the cross pointer across the map and push
<ENTER>. The location of the destination
is modified.
INFO:
. The map scale can be changed by pushing
<ZOOM IN> or<ZOOM OUT> (if so
equipped) . The map scale can also be
changed by touching the scale icon.
. The same screen as when [Move Location]
is touched can be displayed with the
following operations:
— Touching the map screen.
— Pushing the directional buttons except up/down buttons (multi-function control-
ler with directional buttons) .
— Pushing the slide switch except upward/ downward (multi-function controller with-
out directional buttons) .
STORING LOCATION
A searched location can be stored in the
Address Book. Then it can be easily retrieved
and set as a destination (or waypoint) .
1. Highlight [Store Location] and push <ENTER>.
2. The location is stored in the Address Book.The corresponding icon is displayed at the
set location on the map.
VIEWING INFORMATION ABOUT
SEARCHED LOCATION
Information (street address and phone number)
about places stored in the map data can be
displayed.
Route guidance5-5

GUIDANCE SCREEN SETTINGS
The guidance screen can be displayed at all
times even when the vehicle is located away
from the guide point. The screen to be displayed
can be set.
Split screen settings
The display setting on the left-hand side screen
shown during route guidance can be changed.
1. Push<ENTER> while the current location
map screen is displayed.
2. Highlight [Map View ] and push <ENTER>.
3. Highlight [View Settings] and push
<ENTER>.
4. Highlight the preferred screen and push <ENTER>. The indicator of the selected
screen illuminates.
Intersection:
The map screen and the enlarged intersection
view can be displayed at the same time.
Push <MAP> to switch to the full map screen. Turn list:
The list screen for showing the guide points to
the destination and the map screen can be
displayed at the same time. An enlarged
intersection view is automatically displayed
when the vehicle approaches the guide point.
Turn list can be scrolled using the center dial,
the main directional buttons or slide switch by
touching the up/down buttons on the screen.
Push
<MAP> to switch to the full map screen.
Push <MAP> again to display the turn list.
Route guidance5-9

Fuel Economy:
The current fuel consumption rate, average fuel
consumption rate, instantaneous fuel consump-
tion rate and distance to empty can be displayed
on the map screen. An enlarged intersection
view is automatically displayed when the vehicle
approaches the guide point.
Push<MAP> to switch to the full map screen.
Push <MAP> again to display the fuel economy
screen. When approaching a guide point, the
enlarged view of the intersection is automatically
displayed. To display the fuel economy informa-
tion, push <MAP>. To display the map screen,
push <MAP> again.
NOTE:
Use the values displayed on the fuel
economy screen as a guide. When the fuel
gauge indicates empty or the low fuel
warning light illuminates even if the dis- tance to entry reading indicates a suffi-
cient amount of fuel remains, refuel the
vehicle as soon as possible.
Full map:
The current location map is displayed. An
enlarged intersection view is automatically dis-
played when the vehicle approaches the guide
point.
When an enlarged intersection view is dis-
played, pushing
<MAP>returns to the map
screen.
Show exit information on freeways
When the vehicle travels on a highway or a toll
road, the display automatically provides exit
information in the turn list.
1. Push <ENTER> while the current location
map screen is displayed.
2. Highlight [Map View] and push <ENTER>.
3. Highlight [Map Settings] and push
<ENTER>.
5-10Route guidance

4. Highlight [Show all Freeway Exits on Route]or [Auto. Show Turn List on Freeway] and
push <ENTER>. The indicator illuminates
when the item is set.
5. Push <MAP>to return to the current
location map screen.
Showing freeway exit information:
When [Show all Freeway Exits on Route] is set
to ON and the route includes a freeway or toll
road, all exits along the route which have exit
information will be shown in the turn list. The exit information is shown as icons.
Displaying turn list automatically on free-
way:
When [Auto. Show Turn List on Freeway] is set
to ON, the turn list will be automatically
displayed while the vehicle travels on a freeway
or a toll road.
Selecting a waypoint from the exit infor-
mation list:
When exit information is displayed in the turn list,
a waypoint to a facility located near the freeway
exit can be set as a waypoint.
1. Highlight the exit where the exit information
icon is displayed, and push <ENTER>. The
category list screen is displayed.
2. Highlight the landmark category and push <ENTER>. The list screen for showing
facilities located near the freeway exit is
displayed.
3. Highlight the preferred facility for the way-point and push <ENTER>.
Route guidance5-11

4. The waypoint is set, and the route search isperformed.
“Procedures after setting destination”
(page 5-2)
WARNING
Always stop the vehicle in a safe
location before modifying the route
conditions.
Modifying the route conditions while
driving may cause an accident.
During route guidance, the route conditions can
be modified and the route information can be
confirmed. Set route conditions according to
personal preference.
BASIC OPERATION
1. Push <ROUTE>.
2. Highlight the preferred setting item and push <ENTER>.
3. Push <MAP>to return to the current
location map screen.
Available setting items
. [Cancel Route/Resume Route]:
Cancel the current route guidance. A
canceled route can also be reactivated. If
the suggested route is canceled, [Cancel
Route] changes to [Resume Route].
“Canceling/reactivating route”
(page 5-13)
. [Edit/Add to Route]:
Edit or add a destination or waypoints to the
route that is already set.
“Editing route” (page 5-14)
. [Route Info]:
Confirm the route by the route information or
simulation. The confirmed route can also be
stored.
“Confirming route” (page 5-18)
. [Guidance Settings]:
Activate or deactivate route, voice guidance
and/or traffic announcement and adjust the
volume level of voice guidance.
“Guidance settings” (page 5-20)
. [Recalculate]:
Manually search for the route again after
changing the search condition.
“Recalculating route” (page 5-21)
ROUTE SCREEN
5-12Route guidance