navigation NISSAN GT-R 2016 R35 Multi Function Display Workshop Manual


> (GLW    0RGHO 51 @
2-42Navigation
on the right side of the screen.
INFO:
Select [By Distance] to sort the list by the
nearest distance.
6. The selected destination is displayed at the center of the map. Highlight [Start] after
confirming the location of the displayed
destination, and push <ENTER>.
The system sets the destination to the
selected location and starts calculating a route.
INFO:
Even after setting a destination, the location
of the destination can be adjusted, the route
can be stored, etc.
ªProcedures after setting destinationº
(page 2-44)
SETTING POINT ON MAP
It is possible to set a location scrolled to on the
map as the destination and have the system
calculate a route.
1. Scroll the map, place the cross pointer over the preferred location, and push <ENTER>.
INFO:
.The map scale should be adjusted to
search for a location more effectively.
.The point on the blinking road where thecenter of the cross pointer is located can
be set as a destination.
2. Highlight [New Dest.] and push <ENTER>.
INFO:
For the items other than [New Dest.], refer to
ªMap menu screenº.
ªScrolled location map screenº
(page 2-20)
&RQGLWLRQ /DQJXDJH 1$0B(QJOLVK


> (GLW    0RGHO 51 @
3.The system sets the destination to the
selected location and starts calculating a
route.
INFO:
If a point on a freeway is set as the destination, a
confirmation message is displayed.
DELETE DESTINATION
It is possible to delete a destination and all
waypoints that have already been set.
1. Press <DEST>.
2. Select [Delete Destination] and press
<ENTER>.
3. A confirmation message is displayed. Select
[Yes] and press <ENTER>.
The destination and the waypoints are
deleted.
INFO:
The deleted destination and waypoints are not
able to be reactivated.
Setting by voice command
1. Push <
>on the steering wheel.
2. After the tone sounds, speak a command.
To delete a destination and all waypoints:
ªDelete Destinationº (Alternate Command
Mode)
Navigation2-43
&RQGLWLRQ /DQJXDJH 1$0B(QJOLVK


> (GLW    0RGHO 51 @
2-44Navigation
PROCEDURES AFTER SETTING
DESTINATION
After performing a route search, the route
guidance can be immediately started. Also, it is
possible to confirm or change a route.
Available items after setting destination
.[Start]:
Starts route guidance to the selected
destination.
ªStarting route guidanceº (page 2-44)
. [More Routes]:
Displays 3 alternative routes.
ªSelecting routeº (page 2-44)
. [Add/Route Info]:
Displays the route information. A destination
or a waypoint can also be added.
ªConfirming routeº (page 2-45) .
[Move Location]:
Displays a map screen. The location of the
destination can be adjusted.
ªMoving location of destinationº
(page 2-46)
. [Store Location]:
Stores the location in the Address Book.
ªStoring locationº (page 2-47)
. [Place Info]:
Displays information about the facility that
has been set as the destination, if it is
included in the map data.
ªViewing information about searched
locationº (page 2-47)
INFO:
. If no operations have been performed on the
system for several seconds, [Start] is auto-
matically selected, and the system starts
route guidance.
. When using waypoints, [More Routes] is
disabled. After the route is started, push
<ROUTE VOICE> then select [Edit/Add to
Route] to change the route between each
waypoint.
ªEditing routeº (page 2-55) .
Even if the map screen is touched, the same
map screen as when [Move Location] is
selected is displayed.
Starting route guidance
1.Highlight [Start] and push <ENTER>.
Route guidance starts.
Selecting route
1. Highlight [More Routes] and push
<ENTER>.
ROUTE GUIDANCE
&RQGLWLRQ /DQJXDJH 1$0B(QJOLVK


> (GLW    0RGHO 51 @
2. Highlight the preferred route condition andpush <ENTER>.
3. The display automatically returns to the map screen.
Available route conditions
. [Short. Time] (purple):
Prioritizes by the shortest time.
. [Min. Freeway] (orange):
Minimizes the use of freeways.
. [Short. Dist.] (green):
Prioritizes by the shortest distance.
INFO:
. When the route is selected, a preview is
displayed on the right side of the screen.
. The 3 routes may not always be different.
Confirming route
1.Highlight [Add/Route Info] and push
<ENTER>.
2. Highlight the preferred information item and push <ENTER>.
3. Push <BACK> to return to the previous
screen.
Available information
. [Turn List]:
Displays the details of the suggested route.
ªUsing turn listº (page 2-60)
. [Preview]:
The system will trace the planned route
going forward or in reverse.
ªUsing route previewº (page 2-60)
. [Add Way Pt.]:
Edits the route by adding a waypoint or a
destination.
ªAdding destination or waypointº
(page 2-46)
. [Store Route]:
Stores a calculated route. A maximum of 5
routes can be stored. Stored routes can be
easily retrieved and set as the suggested
route.
ªStoring routeº (page 2-73)
. [Map Scroll]:
Displays a map screen where the location of
the destination can be confirmed. Even if the
map screen is touched, the same map
screen as when [Map Scroll] is selected is
displayed.
Navigation2-45
&RQGLWLRQ /DQJXDJH 1$0B(QJOLVK


> (GLW    0RGHO 51 @
2-46Navigation
Adding destination or waypoint:
Before starting route guidance, destinations
and/or waypoints can be added. A total of 6
destinations or waypoints can be set.
1.Highlight [Add Way Pt.] and push
<ENTER>.
2. Set additional destinations or waypoints and
push <ENTER>.
The method of searching for a location is the
same as the one for a destination.
ªSetting destinationº (page 2-23)
3. Highlight [Add Destination] or [Add Way- point] and push <ENTER>.
4. The system starts calculating a route that
includes the added destination or waypoint.
When the calculation is finished, the route is
displayed.
INFO:
.If a waypoint was added, [More Routes]cannot be selected.
.If a destination was added, the priordestination becomes a waypoint.
Moving location of destination
The location of the destination can be adjusted
by moving the cross pointer across the map.
1. Highlight [Move Location] and push
<ENTER>.
INFO:
The screen for adjusting the location also
changes by touching the map screen dis-
played on the right side of the screen.
&RQGLWLRQ /DQJXDJH 1$0B(QJOLVK


> (GLW    0RGHO 51 @
2. Adjust the location by moving the crosspointer across the map and push
<ENTER>. The location of the destination
is modified.
INFO:
Even if the map screen is touched, the same
map screen as when [Move Location] is
selected is displayed.
Storing location
A searched location can be stored in the
Address Book. Then it can be easily retrieved
and set as a destination (or waypoint) .
1. Highlight [Store Location] and push
<ENTER>.
2. The location is stored in the Address Book.
The corresponding icon is displayed at the
set location on the map.
Viewing information about searched
location
Information (street address and phone number)
about places stored in the map data can be
displayed.
1. Select [Place Info] and push <ENTER>.
2. Information about the location is displayed.
3. Push<BACK> to return to the previous
screen.
Navigation2-47
&RQGLWLRQ /DQJXDJH 1$0B(QJOLVK


> (GLW    0RGHO 51 @
2-48Navigation
INFO:
. If [Call] is displayed on the right side of the
screen, it is possible to call the location
indicated.
. The Bluetooth


> (GLW    0RGHO 51 @
direction) .º
ªFreeway entrance on your right onto (road
number and direction) .º
*3ªIn about one mile (1.6 kilometers) , exit on your
right.º
ªExit on your right.º
*4ªYou have arrived at your destination. Ending
route guidance.º
Guidance screens and preview
mode
Route guidance displays map screens and
various information according to the situation.
When route guidance starts, the Small Turn
Arrow on Map is displayed in the upper left
corner of the map screen. This arrow indicates
the turning direction at the next guide point
(corner or intersection) . The distance is also
displayed. At the top of the screen, the distance
to the next guide point and the name of the next
street to turn on to are displayed. Also, theremay be cases that next street names are
announced. The Small Turn Arrow on Map can
be enabled or disabled by the user.
ªDisplaying small turn arrow on mapº
(page 2-68)
Enlarged intersection view:
When approaching a guide point, the system
automatically changes to the split screen and
shows an enlarged view of the intersection on
the left screen. After passing through the
intersection, the system automatically returns
to the full screen mode. To switch to the full
screen mode while the enlarged intersection
view is displayed, push <MAP>. Pushing
<MAP> again displays the enlarged intersec-
tion view. Junction guidance:
While driving on a freeway, when the vehicle is
approximately 1 mile (approximately 2 km) from a
junction, the system automatically switches to
the split screen and displays an enlarged view of
the junction (3D) on the left screen. After
passing the junction, the system automatically
returns to the full screen mode. To switch to the
full screen mode while the enlarged junction
view is displayed, push
<MAP>.
Navigation2-49
&RQGLWLRQ /DQJXDJH 1$0B(QJOLVK


> (GLW    0RGHO 51 @
2-50Navigation
Turn list:
Depending on the setting, the system can
constantly display the split screen and show
the turn list on the left screen. When approach-
ing a guide point, the left screen automatically
switches to an enlarged view of the intersection.
To switch to the full screen mode, push
<MAP>. Pushing<MAP>again displays the
turn list.
Guidance screen settings
The guidance screen can be displayed at all
times even when the vehicle is located away
from the guide point. Various types of screens
can be set.
Split screen settings:
The display setting on the left-hand side screen
shown during route guidance can be changed.
1. Push <ENTER> while the current location
map screen is displayed.
2. Highlight [Map View] and push <ENTER>.
3.Highlight [View Settings] and push
<ENTER>.
4. Highlight the preferred screen and push <ENTER>. The indicator of the selected
screen illuminates.
. Intersection
The map screen and the enlarged intersection
view can be displayed at the same time.
Push <MAP> to switch to the full map screen.
. Turn list
The list screen for showing the guide points to
&RQGLWLRQ /DQJXDJH 1$0B(QJOLVK


> (GLW    0RGHO 51 @
the destination and the map screen can be
displayed at the same time. An enlarged
intersection view is automatically displayed
when the vehicle approaches the guide point.
The turn list can be scrolled using the center dial
or by touching the up/down buttons on the
screen.
Push<MAP> to switch to the full map screen.
Push <MAP> again to display the turn list.
. Fuel Economy
The current fuel consumption rate, average fuel
consumption rate, instantaneous consumption
rate and distance to empty can be displayed on
the map screen. An enlarged intersection view is
automatically displayed when the vehicle ap-
proaches the guide point.
Push <MAP> to switch to the full map screen.
Push <MAP> again to display the fuel economy
screen. When approaching a guide point, the enlarged view of the intersection is automatically
displayed. To display the fuel economy informa-
tion, push
<MAP>.
To display the map screen, push <MAP>again.
NOTICE
Use the values displayed on the fuel
economy screen as a guide. When the
fuel gauge indicates empty or the low
fuel warning light illuminates even if
the distance to empty reading indicates
a sufficient amount of fuel remains,
refuel the vehicle as soon as possible.
. Full map
The current location map is displayed. An
enlarged intersection view is automatically dis-
played when the vehicle approaches the guide
point. When an enlarged intersection view is dis-
played, pushing
<MAP>returns to the map
screen.
Show exit information on freeways:
When the vehicle travels on a highway or a toll
road, the display automatically provides exit
information in the turn list.
1. Push <ENTER> while the current location
map screen is displayed.
2. Highlight [Map View] and push <ENTER>.
Navigation2-51
&RQGLWLRQ /DQJXDJH 1$0B(QJOLVK