NISSAN LATIO 2007 Service Repair Manual
Page 751 of 2896
BL-262
BODY REPAIR
Revision: June 20062007 Versa
Foam RepairEIS0 09 C2
During factory body assembly, foam insulators are installed in certain body panels and locations around the
vehicle. Use the following procedure(s) to replace any factory-installed foam insulators.
URETHANE FOAM APPLICATIONS
Use commercially available spray foam for sealant (foam material) repair of material used on vehicle. Read
instructions on product for fill procedures.
FILL PROCEDURES
1. Fill procedures after installation of service part.
–Remove foam material remaining on vehicle side.
–Clean area in which foam was removed.
–Install service part.
–Insert nozzle into hole near fill area and fill foam material or fill in enough to close gap with the service
part.
2. Fill procedures before installation of service part.
–Remove foam material remaining on vehicle side.
–Clean area in which foam was removed.
–Fill foam material on wheelhouse outer side.
NOTE:
Fill in enough to close gap with service part while avoiding
flange area.
–Install service part.
NOTE:
Refer to label for information on working times.
LIIA1081E
LIIA1082E
Page 752 of 2896
BODY REPAIR
BL-263
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: June 20062007 Versa
1. Body side outer 2. Front pillar lower reinforcement 3. Body side insulation (foam) front pil-
lar
4. Roof panel assembly 5. Body side insulation (Foam) rear
roof rail6. Rear roof rail assembly
7. Body side insulation strip, center pil-
lar8. Body side insulation strip, rear pillar
lower9. Body side insulation strip, rear pillar
upper
LIIA2665E
Page 753 of 2896
BL-264
BODY REPAIR
Revision: June 20062007 Versa
Replacement OperationsEIS009AN
DESCRIPTION
This section is prepared for technicians who have attained a high level of skill and experience in repairing col-
lision-damaged vehicles and also use modern service tools and equipment. Persons unfamiliar with body
repair techniques should not attempt to repair collision-damaged vehicles by using this section.
Technicians are also encouraged to read Body Repair Manual (Fundamentals) in order to ensure that the orig-
inal functions and quality of the vehicle can be maintained. The Body Repair Manual (Fundamentals) contains
additional information, including cautions and warnings, that are not including in this manual. Technicians
should refer to both manuals to ensure proper repairs.
Please note that this information is prepared for worldwide usage, and as such, certain procedures may not
apply in some regions or countries.
Page 754 of 2896
BODY REPAIR
BL-265
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: June 20062007 Versa
The symbols used in this section for cutting and welding / brazing operations are shown below.
PIIA0149E
Page 755 of 2896
BL-266
BODY REPAIR
Revision: June 20062007 Versa
Front pillar butt joint can be determined anywhere within shaded
area as shown in the figure. The best location for the butt joint is
at position A due to the construction of the vehicle. Refer to the
front pillar section.
Determine cutting position and record distance from the locating
indent. Use this distance when cutting the service part. Cut outer
front pillar over 60 mm above inner front pillar cut position.
Prepare a cutting jig to make outer pillar easier to cut. Also, this
will permit service part to be accurately cut at joint position.
An example of cutting operation using a cutting jig is as follows.
1. Mark cutting lines.
A: Cut position of outer pillar
B: Cut position of inner pillar
2. Align cutting line with notch on jig. Clamp jig to pillar.
3. Cut outer pillar along groove of jig. (At position A)
4. Remove jig and cut remaining portions.
5. Cut inner pillar at position B in same manner.
PIIA0150E
PIIA0151E
PIIA0152E
PIIA0153E
Page 756 of 2896
BODY REPAIR
BL-267
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: June 20062007 Versa
RADIATOR CORE SUPPORT
Work after radiator core support upper and lower bolt on crossmembers have been removed.
LIIA2661E
Page 757 of 2896
BL-268
BODY REPAIR
Revision: June 20062007 Versa
Change Parts
Radiator core side support Radiator core support upper
Page 758 of 2896
BODY REPAIR
BL-269
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: June 20062007 Versa
HOODLEDGE LH
Work after radiator core support upper and lower have been removed.
LIIA2612E
Page 759 of 2896
BL-270
BODY REPAIR
Revision: June 20062007 Versa
Change Parts
Hoodledge reinforcement assemblyFront strut housingFender bracket
Cowl top side upperHoodledge upperHoodledge connector
Page 760 of 2896
BODY REPAIR
BL-271
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: June 20062007 Versa
HOODLEDGE RH
Work after radiator core support upper and lower have been removed.
LIIA2613E