NISSAN LEAF 2019 Owner´s Manual
Page 251 of 610
2. Using both hands, simultaneously pressand hold the desired HomeLink® button
and the hand-held transmitter button.
During training, your hand-held trans-
mitter may automatically stop transmit-
ting. Continue to press and hold the de-
sired HomeLink® button while you press
and re-press (“cycle”) your hand-held
transmitter every two seconds until the
frequency signal has been learned. The
HomeLink® indicator light will flash
slowly and then rapidly af ter several
seconds upon successful training. DO
NOT release until the HomeLink® indica-
tor light flashes slowly and then rapidly.
When the indicator light flashes rapidly,
both buttons may be released. The rapid
flashing indicates successful training.
Proceed with “Programming HomeLink®”
step 3 to complete.
If the device was unplugged during the
programming procedure, remember to
plug it back in when programming is com-
pleted.OPERATING THE HOMELINK®
UNIVERSAL TRANSCEIVER
The HomeLink® Universal Transceiver, af ter
it is programmed, can be used to activate
the programmed device. To operate, sim-
ply press and release the appropriate pro-
grammed HomeLink® Universal Trans-
ceiver button. The amber indicator light will
illuminate while the signal is being trans-
mitted.
For convenience, the hand-held transmit-
ter of the device may also be used at any
time.
PROGRAMMING TROUBLE-
DIAGNOSIS
If HomeLink® does not quickly learn the
hand-held transmitter information, per-
form the following steps.
• Replace the hand-held transmitter bat- teries with new batteries.
• Position the hand-held transmitter with its battery area facing away from the
HomeLink® surface. • Push and hold both the HomeLink® and
hand-held transmitter buttons without
interruption.
• Position the hand-held transmitter 1 to 3 inches (2 to 8 cm) away from the
HomeLink® surface. Hold the transmitter
in that position for up to 15 seconds. If
HomeLink® is not programmed within
that time, try holding the transmitter in
another position while keeping the indica-
tor light in view at all times.
If you continue to have programming diffi-
culties, please contact the NISSAN Con-
sumer Affairs Department. The phone
numbers are located in the Foreword of
this Owner’s Manual.CLEARING THE PROGRAMMED
INFORMATION
The following procedure clears the pro-
grammed information from both buttons.
Individual buttons cannot be cleared. How-
ever, individual buttons can be repro-
grammed. For additional information, refer
to “Reprogramming a single HomeLink®
button” in this section.
2-78Instruments and controls
Page 252 of 610
To clear all programming:
1. Press and hold the two outer HomeLink®buttons until the indicator light begins to
flash in approximately 10 seconds. Do
not hold for longer than 20 seconds.
2. Release both buttons.
HomeLink® is now in the programming
modeandcanbeprogrammedatanytime
beginning with “Programming HomeLink®” -
Step 1.
REPROGRAMMING A SINGLE
HOMELINK® BUTTON
To reprogram a HomeLink® Universal
Transceiver button, complete the following:
1. Press and hold the desired HomeLink® button. DO NOT release the button.
2. The indicator light will begin to flash af ter 20 seconds. Without releasing the
HomeLink® button, proceed with “Pro-
gramming HomeLink®” - Step 1.
For questions or comments, contact
HomeLink® at: www.homelink.com or
1–800–355–3515. The HomeLink® Universal Transceiver but-
ton has now been reprogrammed. The
new device can be activated by pushing
the HomeLink® button that was just pro-
grammed. This procedure will not affect
any other programmed HomeLink® but-
tons.
IF YOUR VEHICLE IS STOLEN
If your vehicle is stolen, you should change
the codes of any non-rolling code device
that has been programmed into
HomeLink®. Consult the owner’s manual of
each device or call the manufacturer or
dealer of those devices for additional infor-
mation.
When your vehicle is recovered, you will
need to reprogram the HomeLink® Uni-
versal Transceiver with your new trans-
mitter information.
FCC notice:
For USA:
This device complies with Part 15 of the
FCC Rules. Operation is subject to the fol-
lowing two conditions: (1) This device
may not cause harmful interference, and
(2) this device must accept any interfer-
ence received, including interference
that may cause undesired operation.
NOTE:
Changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s author-
ity to operate the equipment.
For Canada:
This device complies with Industry
Canada licence-exempt RSS standard(s).
Operation is subject to the following two
conditions: (1) this device may not cause
interference, and (2) this device must ac-
cept any interference, including interfer-
ence that may cause undesired opera-
tion of the device.
Instruments and controls2-79
Page 253 of 610
NOTES
2-80Instruments and controls
Page 254 of 610
3 Pre-driving checks and adjustments
Keys ..............................3-2NISSAN Intelligent Key® ................3-3
NISSAN Vehicle Immobilizer System keys . . . .3-3
Doors ............................ .3-4
Locking with key (driver’s side only) ........3-5
Locking with inside lock knob ............3-5
Locking with power door lock switch .......3-5
Automatic door locks ................ .3-6
Child safety rear door lock ..............3-6
NISSAN Intelligent Key® system .............3-6
NISSAN Intelligent Key® operating range of
the door lock/unlock function ...........3-8
Door locks/unlocks precaution ...........3-9
NISSAN Intelligent Key® operation ........3-10
12-volt battery saver system ............3-11
Warning signals ................... .3-12
Troubleshooting guide ................3-12 How to use remote keyless entry function . . .3-14
Hood ............................ .3-17
Rear hatch ......................... .3-18
Secondary rear hatch release ...........3-19
Charge port lid .......................3-20
Opening charge port lid ...............3-20
Charge port cap ................... .3-22
Steering wheel .......................3-23
Tilt operation ......................3-23
Sun visors ......................... .3-23
Vanity mirror ......................3-24
Mirrors ........................... .3-24
Inside rearview mirror ................3-24
Manual anti-glare rearview mirror
(if so equipped) ................... .3-25
Automatic anti-glare type (if so equipped). . .3-25
Outside mirrors ................... .3-26
Page 255 of 610
A key number plate is supplied with your
keys. Record the key number and keep it in
a safe place (such as your wallet), not in the
vehicle. If you lose your keys, it is recom-
mended that you visit a NISSAN certified
LEAF dealer for duplicates by using the key
number. NISSAN does not record any key
numbers so it is very important to keep
track of your key number plate.
A key number is only necessary when you
have lost all keys and do not have one to
duplicate from. If you still have a key, it can
be duplicated without knowing the key
number.
NOTE:
Do not leave the keys inside the vehicle
when leaving the vehicle.
NISSAN INTELLIGENT KEY®
1. Intelligent Key (two sets)
2. Mechanical key (inside Intelligent Key)
3. Key number plate (one plate)
Your vehicle can only be driven with the
Intelligent Keys which are registered to
your vehicle’s Intelligent Key system com-
ponents and NISSAN Vehicle Immobilizer
System components.
As many as four Intelligent Keys can be
registered and used with one vehicle. The
new keys must be registered by a NISSANcertified LEAF dealer prior to use with the
Intelligent Key system and NISSAN Vehicle
Immobilizer System of your vehicle. Since
the registration process requires erasing all
memory in the Intelligent Key components
when registering new keys, be sure to take
all Intelligent Keys that you have to the
NISSAN certified LEAF dealer.
CAUTION
Be sure to carry the Intelligent Key with
you when driving. The Intelligent Key is
a precision device with a built-in trans-
mitter. To avoid damaging it, please
note the following.
• The Intelligent Key is water resis- tant; however, wetting may damage
the Intelligent Key. If the Intelligent
Key gets wet, immediately wipe until
it is completely dry.
• Do not bend, drop or strike it against another object.
• If the outside temperature is below 14°F (-10°C) degrees, the battery of
the Intelligent Key may not function
properly.
• Do not place the Intelligent Key for an extended period in a place where
temperatures exceed 140°F (60°C).
KEYS
3-2Pre-driving checks and adjustments
Page 256 of 610
• Do not change or modif y the Intelli-gent Key.
• Do not use a magnet key holder.
• Do not place the Intelligent Key near an electric appliance such as a tele-
vision set, personal computer or cel-
lular phone.
• Do not allow the Intelligent Key to come into contact with water or salt
water, and do not wash it in a wash-
ing machine. This could affect the
system function.
If an Intelligent Key is lost or stolen,
NISSAN recommends erasing the ID
code of that Intelligent Key. This will
prevent the Intelligent Key from unau-
thorized use to unlock the vehicle. For
information regarding the erasing pro-
cedure, it is recommended that you
visit a NISSAN certified LEAF dealer.
Mechanical key
To remove the mechanical key, release the
lock knob at the back of the Intelligent Key.
To install the mechanical key, firmly insert it
into the Intelligent Key until the lock knob
returns to the lock position.
Use the mechanical key to lock or unlock
the doors. For additional information, refer
to “Doors” in this section.
CAUTION
Always carry the mechanical key in-
stalled in the Intelligent Key.
NISSAN VEHICLE IMMOBILIZER
SYSTEM KEYS
You can only drive your vehicle using the
master keys which are registered to the
NISSAN Vehicle Immobilizer System com-
ponents in your vehicle. These keys have a
transponder chip in the key head.
The master key can be used for all the
locks.
To protect belongings when you leave a
key with someone, give them the Intelligent
Key only, not the mechanical key.
Never leave these keys in the vehicle.
Additional or replacement keys:
If you still have a key, the key number is not
necessary when you need extra NISSAN
Vehicle Immobilizer System keys. A NISSAN
certified LEAF dealer can duplicate your ex-
isting key. As many as four NISSAN Vehicle
Immobilizer System keys can be used with
one vehicle. You should bring all NISSAN
Vehicle Immobilizer System keys that you
have to the NISSAN certified LEAF dealer for
registration. This is because the registra-
tion process will erase the memory of all
key codes previously registered into the
Pre-driving checks and adjustments3-3
Page 257 of 610
NISSAN Vehicle Immobilizer System. Af ter
the registration process, these compo-
nents will only recognize keys coded into
the NISSAN Vehicle Immobilizer System
during registration. Any key that is not
given to the dealer at the time of registra-
tion will no longer be able to start your
vehicle.
CAUTION
Do not allow the immobilizer system
key, which contains an electrical tran-
sponder, to come into contact with wa-
ter or salt water. This could affect sys-
tem function.
WARNING
• Always have the doors locked while driving. Along with the use of seat
belts, this provides greater safety in
the event of an accident by helping
to prevent persons from being
thrown from the vehicle. This also
helps keep children and others from
unintentionally opening the doors,
and will help keep out intruders.
• Before opening any door, always look for and avoid oncoming traffic.
•
To help avoid risk of injury or death
through unintended operation of the
vehicle and/or its systems, including
entrapment in windows or inadver-
tent door lock activation, do not leave
children, people who require the as-
sistance of others or pets unattended
in your vehicle. Additionally, the tem-
perature inside a closed vehicle on a
warm day can quickly become high
enough to cause a significant risk of
injury or death to people and pets.
When the doors are locked using one of the
following methods, the doors cannot be
opened using the inside or outside door
handles. The doors must be unlocked to
open the doors.
DOORS
3-4Pre-driving checks and adjustments
Page 258 of 610
LOCKING WITH KEY (DRIVER’S SIDE
ONLY)
To lock or unlock the vehicle, turn the key as
shown.
Manual
To lock a door, turn the key towards the
front of the vehicle
1. To unlock, turn the
key toward the rear of the vehicle
2.
LOCKING WITH INSIDE LOCK KNOB
To lock the door without the key, move the
inside lock knob to the lock position
1
then close the door.
To unlock, move the inside lock knob to the
unlock position
2.
When locking the door without a key, be
sure not to leave the key inside the ve-
hicle.
LOCKING WITH POWER DOOR
LOCK SWITCH
Operating the power door lock switch will
lock or unlock all the doors. The switches
are located on the driver’s and front pas-
senger’s door armrests.
To lock the doors, push the power door lock
switch to the lock position
1with the driv-
er’s or front passenger’s door open, then
close the door.
When locking the door this way, be sure
not to leave the key inside the vehicle.
Pre-driving checks and adjustments3-5
Page 259 of 610
To unlock the doors, push the power door
lock switch to the unlock position
2.
Lockout protection
When the power door lock switch is moved
to the lock position while any door is open,
all doors will unlock automatically and a
chime will sound af ter the door is closed.
This function help to prevent the Intelligent
Key from being accidentally locked inside
the vehicle.
AUTOMATIC DOOR LOCKS
• All doors lock automatically when the ve-hicle speed reaches 15 mph (24 km/h).
• All doors unlock automatically when the ignition is placed in the OFF position.CHILD SAFETY REAR DOOR LOCK
Child safety rear door locks help prevent
the rear doors from being opened acciden-
tally, especially when small children are in
the vehicle.
When the levers are in the lock position
1, the rear doors can be opened only
from the outside.
To disengage, move the levers to the un-
lock position
2.
WARNING
• Radio waves could adversely affect electric medical equipment. Those
who use a pacemaker should con-
tact the electric medical equipment
manufacturer for the possible influ-
ences before use.
• The Intelligent Key transmits radio waves when the buttons are
pressed. The FAA advises that the ra-
dio waves may affect aircraf t navi-
gation and communication sys-
tems. Do not operate the Intelligent
Key while on an airplane. Make sure
the buttons are not operated unin-
tentionally when the unit is stored
during a flight.
The Intelligent Key system can operate all
the door and the rear hatch locks by using
the remote control function or pushing
the request switch on the vehicle without
taking the key out from a pocket or purse.
The operating environment and/or condi-
tions may affect the Intelligent Key system
operation.
NISSAN INTELLIGENT KEY® SYSTEM
3-6Pre-driving checks and adjustments
Page 260 of 610
Be sure to read the following items before
using the Intelligent Key system.
CAUTION
• Be sure to carry the Intelligent Key with you when operating the ve-
hicle.
• Never leave the Intelligent Key in the vehicle when you leave the vehicle.
The Intelligent Key is always communicat-
ing with the vehicle because it receives ra-
dio waves. The Intelligent Key system
transmits weak radio waves. Environmen-
tal conditions may interfere with the op-
eration of the Intelligent Key system under
the following operating conditions.
• When operating near a location where strong radio waves are transmitted, such
as a TV tower, power station or broadcast-
ing station.
• When in possession of wireless equip- ment, such as a cellular phone, transceiver
or a CB radio. • When the Intelligent Key is in contact with
or covered by metallic materials.
• When any type of radio wave remote con- trol is used nearby.
• When the Intelligent Key is placed near an electric appliance such as a personal
computer.
• When the vehicle is parked near a parking meter.
In such cases, correct the operating condi-
tions before using the Intelligent Key func-
tion or use the mechanical key.
Although the life of the battery varies de-
pending on the operating conditions, the
battery’s life is approximately two years. If
the battery is discharged, replace it with a
new one.
When the Intelligent Key battery is almost
discharged, firmly apply the foot brake and
touch the power switch with the Intelligent
Key. Then push the power switch while de-
pressing the brake pedal within 10 seconds
af ter the chime sound. Since the Intelligent Key is continuously re-
ceiving radio waves, if the key is lef t near
equipment that transmits strong radio
waves, such as signals from a TV or per-
sonal computer, the battery life may be-
come shorter.
For additional information, refer to “NISSAN
Intelligent Key® battery replacement” in the
“Maintenance and do-it-yourself ” section
of this manual.
Pay special attention that the vehicle bat-
tery is not completely discharged.
As many as four Intelligent Keys can be
registered and used with one vehicle. For
information about the purchase and use of
additional Intelligent Keys, it is recom-
mended that you visit a NISSAN certified
LEAF dealer.
Pre-driving checks and adjustments3-7