NISSAN MAXIMA 2014 A35 / 7.G 08IT Navigation Manual

SETTING LEFT SCREEN DISPLAY
When the split screen is displayed, the map
settings of the left screen can be changed.
1. Highlight [Left Split Map Settings] and push<ENTER>.
2. Highlight the preferred map view and push<ENTER>.
3. Push <MAP>to return to the current
location map screen.
Available setting items
. [Map Orientation]:
The map direction can be selected as
follows.
— [North Up]:
North is set at the top of the map.
— [Heading Up]: The traveling direction is set at the top of
the map.
. [Long Range]:
The vehicle icon is located slightly lower
than the center of the screen. This offers a
wider view in the traveling direction.
. [Map Scale]:
A scale appears on the left side of the
screen. This changes the scale of a map.
INFO:
. The settings of the right screen are the same
as the settings of the full screen map.
. Touching the icon on the map can also
change the direction and scale of the map. Icons of particular facilities can be displayed on
the map.
DISPLAYING MAP ICONS
Map icons can be displayed or hidden by type.
1. Push
<ENTER> while the current location
map screen is displayed.
2. Highlight [Map Icons] and push <ENTER>.
Map settings3-17
LOOKING AT INFORMATION ON
THE MAP

3-18Map settings
3. Highlight the preferred icon and push<ENTER>. The icon display setting toggles
between on and off each time <ENTER>is
pushed. The indicator of the selected icon
illuminates.
4. Push <MAP>to return to the current
location map screen. The activated icons
are displayed on the map.
INFO:
If registered in the map data, the brand icons will
be displayed on the map instead of the general
map icons listed below.
Map icons that can be displayed
.Restaurant
.
Gas Station
.
Hotel
.
AT M
.
Rest Area
Other settings
Landmark icons can also be set using the
following procedure.
1. Push <SETTING>.
2. Highlight [Navigation] and push <ENTER>.3. Highlight [Map Icons] and push
<ENTER>.
INFO:
The map icons are not displayed on the map
screen when the map scale is set to 1/4 mile
(500 m) or higher in the 2D map, or to 1 mile (2
km) or higher in Birdview
TMmap.
MAP SCROLLING INFORMATION
Information about the location, on which the
center of the cross pointer is placed by scrolling
on the map, can be set to be displayed.
1. Push <SETTING>.
2. Highlight [Navigation] and push <ENTER>.

3. Highlight [Others] and push<ENTER>.
4. Highlight [Map Scrolling Information] and
push <ENTER>.
5. Highlight the preferred information item and
push <ENTER>. The indicator of the
selected information item illuminates.
Available information items:
.[Address Book Icons]
.[Destination/Waypoint Icons]
.[Latitude/Longitude Info.]
6. Push <MAP>to return to the current
location map screen. Move the cross pointer
to the set location to display the information.
Map settings3-19

3-20Map settings
MAP SYMBOLS
This navigation system uses symbols to display
facilities.

ROAD COLOR
The road types are differentiated by colors.
Freeway: Red or Light Red (zoomed in)
Main road: Brown or Dark Yellow
Narrow street: Gray
Road with incomplete map data: Dark green
TRAFFIC INFORMATION ON MAP
With a subscription to NavTraffic service, traffic
information is displayed.
“Viewing available traffic information”
(page 7-3)
Free Flow: Green arrow
Moderate traffic: Yellow arrow
Heavy traffic: Red arrow
Section affected by serious traffic event: Purple
dashed arrow
Traffic information icons:
Accident
Closed road
Information
Road work
Slippery road
Weather
Incident
Map settings3-21

3-22Map settings
MEMO

4 Setting destination
Destination screen .................................................................... 4-2Basic operation .................................................................... 4-2
Changing region .................................................................. 4-2
Finding address ................................................................... 4-4
Finding place ........................................................................\
4-5
Setting home as destination ......................................... 4-10
Searching from address book ...................................... 4-11
Setting previous destination .......................................... 4-12 Setting previous start point ......................................... 4-13
Setting from stored routes .......................................... 4-14
Setting by phone number ............................................ 4-14
Setting freeway entrance/exit ..................................... 4-15
Setting intersection ....................................................... 4-17
Setting city center ......................................................... 4-18
Setting point on map .................................................... 4-19
Delete destination ................................................................. 4-20

4-2Setting destination
There are several methods available to set a
destination. Understand the advantages of each
method and select the best method for finding
and setting a preferred destination.
BASIC OPERATION
1. Push<DEST>.
2. Highlight the preferred destination setting method and push <ENTER>.
Available setting items
.[Street Address]:
Searches for a destination by address.
. [Places]:
Searches for a destination from various
categories of businesses or locations.
. [Home]:
Searches for a route from the current
location to the previously stored home
destination. .
[Address Book]:
Searches for a destination from the list of the
stored locations.
. [Previous Destinations]:
Searches for a destination from the previous
destinations.
. [Delete Destination]:
Deletes the currently set destination.
Available setting items (next page
screen)
.[Previous Start Point]:
Sets the previous starting point as the
destination.
. [Stored Routes]:
Selects a stored route.
. [Phone Number]:
Searches for a point of interest by a
telephone number.
INFO:
The system cannot be used to search for
residential phone numbers. . [Freeway Entrance/Exit]:
Searches for a destination from a freeway
entrance/exit. .
[Intersection]:
Searches for a destination from intersec-
tions.
. [City Center]:
Sets the center of a city as the destination.
CHANGING REGION
When setting a destination, the location can be
narrowed down by specifying the region or city.
Specifying the region
1. Push <DEST>.
2. Highlight [Change Region] and push <ENTER>.
DESTINATION SCREEN

3. Highlight the preferred region and push<ENTER>.
Available setting items: . US1: CA, NV
. US2: AZ, CO, ID, MT, NM, OR, UT, WA, WY
. US3: IA, KS, MN, MO, ND, NE, SD
. US4: AR, LA, MS, OK, TX
. US5: IL, IN, MI, WI
. US6: DC, DE, KY, MD, OH, PA, VA, WV
. US7: CT, MA, ME, NH, NJ, NY, RI, VT
. US8: AL, FL, GA, NC, SC, TN
. US9: AK
. US10: HI
. Canada .
Puerto Rico
. Virgin Islands
INFO:
. It is also possible to select a region by
touching the map on the right side of the
screen.
. It is not possible to search for a route from
the continental United States to Hawaii,
Puerto Rico and Virgin Islands.
Specifying city
When searching for a destination with “Places”,
“Freeway Entrance/Exit”, “Intersection” or “City
Center”, the search can be narrowed down by
specifying the city.
1. Highlight [Select a City] and push
<ENTER>.
2. Enter the name of the city, highlight [List]and push <ENTER>.
A list screen is displayed.
INFO:
.The same screen will be displayed when a location is searched from a street
address, and when [City] is highlighted
and <ENTER> is pushed.
“Finding address” (page 4-4)
.Highlight [Last 5 Cities] and push
<ENTER> to display 5 cities recently
set as destinations.
Setting destination4-3

4-4Setting destination
3. Highlight the city of the destination from thelist and push <ENTER>.
INFO:
In some cases, when a city name has been
entered, the number of matching destinations in
the “Matches” column may be different from the
number displayed on the list screen. If this
occurs, enter more characters to further reduce
the number of matches.
FINDING ADDRESS
When the address of the destination is available,
use this method to enter the address and then
have the system calculate a route. A location
near the preferred destination can also be
searched for by entering the house number if
the map data contains the relevant data.
1. Push <DEST>, highlight [Street Address]
and push <ENTER>. A character input
screen is displayed.
2. Enter the house number, highlight [OK] and push <ENTER>. If the house number is not
available, highlight [No House #] and push
<ENTER>. A street name input screen is
displayed.
3. Enter the name of the street. After finishing the entry, highlight [List] and push
<ENTER>. A list of streets is displayed.
INFO:
When [City] is highlighted and <ENTER>
pushed, a city can be specified by typing the
city name.
“Specifying city” (page 4-3)
4. Highlight the correct street of the destina- tion from the list and push <ENTER>.