NISSAN MURANO 2014 2.G Quick Reference Guide

9
AUTOMATIC DRIVE POSITIONER (if so equipped)
Two positions for the driver’s seat and outside
mirrors can be stored in the automatic drive
positioner memory.

Follow these procedures to set the memory positions:
• Confirm the shift lever is in the P (PARK) position.
• Push the ignition switch to the ON position.
• Adjust the driver’s seat and outside mirrors to the desired positions using the adjusting
switches for each feature.
• Push the SET switch and within 5 seconds push the memory switch (1 or 2) for at
least 1 second.
• The indicator light on the memory switch you select will illuminate for approximately
5 seconds.
• The driver’s seat and outside mirror positions are now set to your preference.

These memorized positions can also be linked to your NISSAN Intelligent Key®.
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
FRONT SEAT ADJUSTMENTS
MANUAL SEATS (Passenger’s side only)

To slide the seat forward or backward, pull up on
the lever 01 under the front of the seat and slide
forward or backward. Release the lever to lock the
seat in position.

To adjust your seatback forward or backward, lift the
lever 02 on the side of the seat.

Release the lever when you have found a comfortable
angle and the seat belt fits properly.
POWER SEATS (Driver’s side only)

To slide the seat forward or backward, push the control switch
03
forward or backward.

To recline the seatback, push the switch
04 forward or backward.
SEAT LIFTER

To adjust the angle of the front seat cushion or
height of the seat, push the front or rear end of the
switch
03 up or down.
LUMBAR SUPPORT

To adjust the seat lumbar support, push the front or back end of the switch
05.
For more information, refer to the “Safety –– Seats, seat belts and supplemental restraint system (section 1)”\
of your
Owner’s Manual.
01
02
030405
1591421_14d_Murano_QRG_012714b.indd 91/27/14 3:11 PM
To view detailed instructional videos regarding these and other features, please go to www.nissanownersinfo.mobi.

10
FIRST DRIVE FEATURES
REAR SEAT ADJUSTMENTS (Hardtop models)
FOLDING DOWN THE REAR SEAT

To fold the seats flat, release the connector tongue of
the rear center seat belt from the buckle, then store
the connector and seat belt tongues in the retractor
base on the ceiling

01.

Fold the seatback forward using either the pull strap

02, located on the outside edge of the rear seat, or
the release lever
03 in the cargo area.

To raise the seatback manually, lift up each seatback
and push it to the upright position until it is latched.

To raise the seatback automatically (if so equipped),
push and hold the power seatback switch
located in
the cargo area
04 or the corresponding seat switch
on the lower side of the instrument panel 05.
– A beep sounds once and the seatback begins to
move automatically.
– A beep sounds twice when the seatback is fully
returned to the upright seating position.
RECLINING THE REAR SEATS

Brace the back of the seat with your arm while
pulling on the strap. The seatback will release quickly.

Pull the reclining strap 02, and move the seatback to the desired angle.

Release the reclining strap after positioning the seat at the desired an\
gle.
For more information, refer to the “Safety – Seats, seat belts and supplemental restraint system (se\
ction 1)” of your
Owner’s Manual.
04
02
01
03
05
REAR SEAT ENTRY/EXIT (CrossCabriolet models)
DRIVER’S SIDE

Pulling the strap behind the driver’s seat does not
slide the driver’s seat forward. You cannot slide the
driver’s seat manually.

To enter the rear seat, push and hold the front end of
the slide switch

01 to slide the driver’s seat forward.

Then push and hold the front end of the reclining
switch

02 until the desired angle is obtained.

To exit the rear seat from the driver’s side, pull the
strap

03 behind the driver’s seat to release the
driver’s seatback. The driver’s seatback will tilt
forward so that you can exit the vehicle.
01
02
03
1591421_14d_Murano_QRG_012714b.indd 101/27/14 3:11 PM
To view detailed instructional videos regarding features in this Quick Reference Guide, please go to www.nissanownersinfo.mobi.

11
OUTSIDE MIRROR CONTROL SWITCH

To select the right or left side mirror, turn the control
switch
01 right or left.


To adjust the mirror angle, move the control switch up,
down, right or left.


To prevent accidentally moving the mirror, turn and set
the switch to the middle (neutral) position.
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
01
STARTING/STOPPING THE ENGINE
It is important to make sure the NISSAN Intelligent
Key® is with you (that is, in your pocket or purse).

Depress the brake pedal.

Press the ignition switch START/STOP button to
start the engine.
TURNING THE ENGINE OFF

Move the shift lever to the P (PARK) position and
apply the parking brake.

Press the ignition switch START/STOP button to turn the engine off.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
04
05
06
PASSENGER’S SIDE

To fold down the front passenger’s seatback and
unlock the seat position, push the front passenger’s
seatback switch
04.

Manually slide the seat to the forward most position.

Enter or exit the back seat.


To slide the front passenger’s seat back into position,
push the bottom half of the seatback

05 until it
locks. Next, adjust the seatback by pulling the
seatback lever
06 up. Release the lever to lock the
seatback into position.
For more information, refer to the “Safety – Seats, seat belts and
supplemental restraint system (section 1)” of your Owner’s Manual.
1591421_14d_Murano_QRG_012714b.indd 111/27/14 3:11 PM
To view detailed instructional videos regarding these and other features, please go to www.nissanownersinfo.mobi.

12
FIRST DRIVE FEATURES
HEADLIGHT CONTROL SWITCH
HEADLIGHT CONTROL

Turn the headlight control switch to the

position 01 to turn on the front parking, side
marker, tail, license plate and instrument panel
lights. Turn the switch to the
position
02 to
turn on the headlights.
AUTOLIGHT SYSTEM (if so equipped)

The autolight system will automatically turn the headlights on when it is\
dark and off when it
is light. The system will keep the headlights on for a period of time after you tur\
n the ignition
off and all doors are closed.

To activate the autolight system, turn the headlight control switch to the AUTO position
03
then push the ignition switch to ON. To deactivate the autolight system, turn the headlight
control switch to the OFF,
position
01 or
position
02.
HIGH BEAM SELECT

Push the headlight control switch forward
04 to

select the high beam function. The blue indicator
light
illuminates in the instrument panel. Pull the
headlight switch back to the original position to select
the low beam. The blue indicator light will extinguish.

Pull and release the headlight control switch
05 to

flash the headlight high beams on and off.
FOG LIGHT SWITCH (if so equipped)

The headlights must be on and the low beams
selected for the fog lights to operate.

Turn the switch (inside collar) to the
position
06 to turn the fog lights on.

Turn the switch (inside collar)
to the OFF position to turn the fog lights off.
LANE CHANGE SIGNAL

To signal a lane change, move the lever up or down to the point where the indicator light
begins to flash, but the lever does not latch.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
01
03
02
0405
06
1591421_14d_Murano_QRG_012714b.indd 121/27/14 3:11 PM
To view detailed instructional videos regarding features in this Quick Reference Guide, please go to www.nissanownersinfo.mobi.

13
WINDSHIELD WIPER AND WASHER SWITCH
Move the lever to the following positions to operate
the windshield wipers:

01 Mist (MIST) - One sweep operation of the
front wipers.

02 Auto (AUTO) (Hardtop models – if so equipped)
Operates the rain-sensing auto front wiper
system. The rain sensor sensitivity level can
be adjusted by twisting the time control
ring
03 to increase or decrease wiper sensitivity.

04 Low (LO) - Front wipers operate at a continuous
low speed.

05 High (HI) - Front wipers operate at a continuous
high speed.

06 Pull the lever toward you to activate the
front washer. The front wipers will operate
several times.
REAR WINDSHIELD WIPER AND WASHER
(Hardtop models)

07 Intermittent (INT) - Rear wiper operates intermittently.

08 Low (ON) - Rear wiper operates at a continuous low speed.

09 Push the lever forward to activate the rear washer. The rear wiper will operate several times.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
01
02
04
05
MIST
OFF
AUTO
LO
HI
0609
03
INT
ON07
08
1591421_14d_Murano_QRG_012714b.indd 131/27/14 3:11 PM
To view detailed instructional videos regarding these and other features, please go to www.nissanownersinfo.mobi.

14
FIRST DRIVE FEATURES
AUTOMATIC CLIMATE CONTROLS (if so equipped)
01 AUTO BUTTON/DRIVER’S SIDE TEMPERATURE CONTROL DIAL

The auto mode may be used year-round. Press the AUTO button to turn the system on,
and the system will automatically control the inside temperature (autom\
atic cooling and/or
dehumidified heating), air flow distribution and fan speed.

Turn the driver’s side temperature control dial to the left for cooler air or right for \
warmer air.
02 DUAL BUTTON/PASSENGER’S SIDE TEMPERATURE CONTROL DIAL

Press the D UAL button to turn the passenger’s side temperature controls on or off. This
will allow the passenger’s side temperature to be adjusted independently from the driver’s
side by turning the passenger’s side temperature control dial.

Turn the passenger’s side temperature control dial left for cooler air or right for warmer \
air.
03 ON•OFF BUTTON/FAN SPEED CONTROL KNOB

Turn the fan speed control knob left to decrease fan speed or right to in\
crease fan speed.

Press the button to turn the system on or off.
04 MODE BUTTON

Press the MODE button
to cycle through the following air flow outlets:

Air flows from the center and side vents.

Air flows from the center, side and foot vents.

Air flows mainly from the foot vents.

Air flows from the defroster and foot vents.
05 INTAKE AIR CONTROL BUTTON
AIR RECIRCULATION

Press the intake air control button to recirculate interior air inside the vehicle. T\
he
indicator light on the button will illuminate. This system is used to avoid certain outside
odors and to adjust the inside vehicle temperature more effectively.

The air recirculation mode cannot be activated when the climate control s\
ystem is in the
front defroster mode

or the front defroster and foot vent mode .
OUTSIDE AIR CIRCULATION

Press the intake air control button
again to draw outside air into the passenger

compartment. The indicator light on the button will turn off.
030201
0506
0904
0708
1591421_14d_Murano_QRG_012714b.indd 141/27/14 3:11 PM
To view detailed instructional videos regarding features in this Quick Reference Guide, please go to www.nissanownersinfo.mobi.

15
06 UPPER VENT BUTTON


When the upper vent button
is pressed, the air flow against the driver’s or passenger’s

upper body becomes gentle. The indicator light on the button will illuminate.


In this mode, air from the upper ventilator flows to control the cabin\
temperature without
blowing air directly on the occupants.
07 DEFROSTING/DEFOGGING FRONT AND SIDE WINDOWS

Press the defroster control button to turn the system on. The A/C automatically turns
on when the defroster mode is selected. This feature removes humidity from the air.

Turn the temperature control dial 01 to set the desired temperature.


To defrost the front and side windows quickly, set the temperature controls and fan speed
controls to their maximum settings.
08 DEFROSTING REAR WINDOW AND OUTSIDE MIRRORS (if so equipped)

Press the rear window defroster switch
REAR
to turn the system on or off.

This function automatically turns off after approximately 15 minutes.
09 A/C BUTTON


Press the A/C button to turn the air conditioner system on or off. This system helps cool
and dehumidify the air inside the cabin and defog the windows.
For more information, refer to the “Instruments and controls (section 2)” and the “Monitor, heater, air conditioner, audio,
phone and voice recognition systems (section 4)” of your Owner’s Manual.
1591421_14d_Murano_QRG_012714b.indd 151/27/14 3:11 PM
To view detailed instructional videos regarding these and other features, please go to www.nissanownersinfo.mobi.

16
FIRST DRIVE FEATURES
03
0506
02
01
FM/AM/SiriusXM®* SATELLITE RADIO WITH CD/DVD PLAYER
(if so equipped)
01 ON•OFF BUTTON/VOL (volume) CONTROL KNOB

Press the VOL/ON•OFF control knob to turn the system on or off.

Turn the knob right or left to increase or decrease the volume.
02 SEEK/CAT AND TRACK BUTTONS

To scan quickly through each broadcasting station, press the SEEK/CAT button or
the TRACK
button to stop at the previous or next broadcast station.

For satellite radio, to switch to the first channel of the previous or next category, press the
SEEK/CAT button or the TRACK button.

To change tracks on a CD, press the SEEK/CAT button or the TRACK button.

To rewind or fast forward a track on a CD, press and hold the SEEK/CAT button or
the TRACK
button.
03 AUDIO BUTTON/TUNE•FOLDER CONTROL KNOB

Press the AUDIO button to go to the audio settings screen.

To manually tune the radio, turn the TUNE/FOLDER knob left or right.
04 STATION PRESET BUTTONS

Twelve stations can be set for the FM band, six for the AM band and eighteen for
satellite radio.

To store a station in a preset, you must first select a radio band by pressing the
AM•FM button
05 or
S AT button
06, then tune to the desired AM, FM or XM
satellite radio station.

Then press and hold the desired station preset button (1-6) until the sound is briefly
muted. The channel indicator will then display and the sound will resume. Programing\
is
now complete.

To retrieve a previously set station, select the radio band where the preset was stored
then press the corresponding station select button (1-6).
*SiriusXM® Satellite Radio is only available on vehicles equipped with an optional s\
atellite radio subscription service.
For more information, refer to the “Monitor, heater, air conditioner, audio, phone and voice recognition systems (section
4)” of your Owner’s Manual.
04
1591421_14d_Murano_QRG_012714b.indd 161/27/14 3:11 PM
To view detailed instructional videos regarding features in this Quick Reference Guide, please go to www.nissanownersinfo.mobi.

17
FRONT ARMREST/CENTER CONSOLE STORAGE BOX
To access the top storage bin, pull
up on the driver’s side lever
01.

To access the bottom storage bin, pull
up on the passenger side lever
02.
For more information, refer to the “Instruments and
controls (section 2)” of your Owner’s Manual.0201
CRUISE CONTROL
The cruise control system enables you to set a
constant cruising speed once the vehicle has
reached 25 MPH (40 km/h).

The system will automatically maintain the set speed
until you tap the brake pedal, accelerate, cancel or
turn the system off.

To activate the cruise control, push the ON/OFF
switch
01. The CRUISE indicator light in the instrument panel will illuminate.

To set a cruising speed, accelerate the vehicle to the desired speed, pus\
h the COAST/SET
switch
02 and release. Take your foot off the accelerator pedal. Your vehicle will maintain

the set speed.

To reset at a faster cruising speed, push and hold the ACCEL/RES switch 03. When the
vehicle attains the desired speed, release the switch.

To reset at a slower cruising speed, push and hold the COAST/SET switch 02. Release
the switch when the vehicle slows to the desired speed.

To cancel the preset speed, tap the brake pedal or push the CANCEL switch 04.

To turn off cruise control, push the ON/OFF switch 01. The CRUISE indicator light
in the
instrument panel will extinguish.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
01
02
03
04
USB/ iP OD® INTERFACE (if so equipped)
The USB jack 01 is located in the center console
under the arm rest.

When a compatible USB memory device or iPod® is
plugged into the USB jack, compatible audio and
video files stored on the device can be played
through the vehicle’s audio system and front display.
For more information, refer to the “Monitor, climate, audio, phone and
voice recognition systems (section 4)” of your Owner’s Manual.01
1591421_14d_Murano_QRG_012714b.indd 171/27/14 3:11 PM
To view detailed instructional videos regarding these and other features, please go to www.nissanownersinfo.mobi.

18
TRIP COMPUTER
When the button 01
is pressed, the following

modes will appear on the vehicle information
display
02 :
• MPG/AVG – Displays the current and average
fuel consumption since the last reset.
• MPG/MPH – Displays the average fuel
consumption and speed since the last reset.
• TIME/miles – Displays the elapsed time and
total distance the vehicle has been driven since
the last reset.
• RANGE – Displays the estimated distance
to empty (dte) the vehicle can be driven
before refueling.
• OUTSIDE TEMP – Displays the exterior air
temperature, including a low temperature
warning feature.
• SETTING – Allows you to set reminders for alerts and maintenance intervals or change
the language and units used in the system.
— Press the

button 03 to cycle through the various setting modes.

— Press the

button 01 to choose the selected menu.

• WARNING – Displays when a warning is present.

Press and hold the TRIP RESET button 04 for approximately 1 second to reset the currently
displayed trip odometer to zero.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
03
01
SYSTEM GUIDE
04
02
1591421_14d_Murano_QRG_012714b.indd 181/27/14 3:11 PM
To view detailed instructional videos regarding features in this Quick Reference Guide, please go to www.nissanownersinfo.mobi.