NISSAN NV200 2019 Owners Manual
Page 191 of 372
WARNING
Use a phone af ter stopping your ve-
hicle in a safe location. If you have to
use a phone while driving, exercise ex-
treme caution at all times so full at-
tention may be given to vehicle
operation.
If you are unable to devote full atten-
tion to vehicle operation while talking
on the phone, pull off the road to a
safe location and stop your vehicle.
CAUTION
To avoid discharging the vehicle bat-
tery, use a phone af ter starting the
engine.
BLUETOOTH® HANDS-FREE PHONE
SYSTEM WITHOUT NAVIGATION
SYSTEM (if so equipped)
Monitor, climate, audio, phone and voice recognition systems4-65
Page 192 of 372
LHA3506
4-66Monitor, climate, audio, phone and voice recognition systems
Page 193 of 372
BLUETOOTH® is a
trademark owned
by Bluetooth SIG,
Inc. and licensed
to Visteon.
Monitor, climate, audio, phone and voice recognition systems4-67
Page 194 of 372
button is pressed before the initialization
completes, the system will announce
phone system not readyŽ and
will not react to voice commands.
Operating tips
To get the best performance out of the
NISSAN Voice Recognition system, observe
the following:
Keep the interior of the vehicle as quiet
as possible. Close the windows to elimi-
nate surrounding noises (traffic noises,
vibration sounds, etc.), which may pre-
vent the system from recognizing voice
commands correctly.
Wait until the tone sounds before
speaking a command. Otherwise, the
command will not be received properly. Start speaking a command within
5 seconds af ter the tone sounds.
Speak in a natural voice without paus-
ing between words.
Giving voice commands
To operate NISSAN Voice Recognition,
press and release the
button located
on the steering wheel. Af ter the tone
sounds, speak a command.
The command given is picked up by the
microphone, and voice feedback is given
when the command is accepted.
If you need to hear the available com-
mands for the current menu again, say
and the system will repeat them.
If a command is not recognized, the
system announces, not
recognized. Please try again.Ž Make sure
the command is said exactly as
prompted by the system and repeat
the command in a clear voice.
If you want to go back to the previous
command, you can say backŽ or
any time the system is
waiting for a response. You can cancel a command when the
system is waiting for a response by say-
ing, or The system an-
nounces and ends the Voice
Recognition session. You can also press
and hold the
button on the steer-
ing wheel for 5 seconds at any time to
end the Voice Recognition session.
Whenever the Voice Recognition ses-
sion is canceled, a double beep is
played to indicate you have exited the
system.
If you want to adjust the volume of the
voice feedback, push the volume con-
trol switches (+ or -) on the steering
wheel while being provided with feed-
back. You can also use the radio volume
control knob.
Voice Prompt Interrupt
In most cases you can interrupt the voice
feedback to speak the next command by
pressing the
button on the steering
wheel. Af ter interrupting the system, wait
for a beep before speaking your command.
4-68Monitor, climate, audio, phone and voice recognition systems
Page 195 of 372
button and af ter
the tone say, RedialŽ.
CONTROL BUTTONS
The control buttons for the Bluetooth®
Hands-Free Phone System are located on
the steering wheel.
PHONE/SEND
Press the
button to initi-
ate a Voice Recognition ses-
sion or answer an incoming
call.You can also use the
button to interrupt the sys-
tem feedback and give a
command at once. For addi-
tional information, refer to
commandsŽ and
ing a callŽ in this section.
PHONE/END
While the voice recognition
system is active, press and
hold the
button for
5 seconds to quit the voice
recognition system at any
time.
Tuning switch
While using the voice recogni-
tion system, tilt the tuning
switch up or down to manu-
ally control the phone system.
LHA2499
Page 196 of 372
Page 197 of 372
button to bring up the
phone command menu. The available op-
tions are:
Call
Phonebook
Recent Calls
Messaging (if so equipped)
Select Phone
For additional information, refer to
a callŽ in this section.
The following commands are available un-
der
(a name)
Say a name in the phonebook to bring
up a list of options for that phonebook
entry. The system will say the name it
interpreted based on the voice com-
mand provided. If the name is incorrect,
say to hear another name.
Once the correct phonebook entry is
identified, say to dial the number
or TextŽ to send a text message to
that number. Say NameŽ to re-
cord a name for the phonebook entry.
Say RecordingŽ to delete a re-
corded name for the phonebook entry.
List Names
Speak this command to have the system
list the names in the phonebook one by
one alphabetically. Say to dial the
number of the current name or
TextŽ to send a text message to that num-
ber. Say Entry Ž or Entry Ž to
move through the list alphabetically. Say
NameŽ to record a name for the
current phonebook entry. Say Re-
cordingŽ to delete a recorded name for
the current phonebook entry.
CallsŽ
The following commands are available un-
der CallsŽ:
Incoming Calls
Speak this command to list the last five
incoming calls to the vehicle. If the call is
from an entry in the phonebook, the
name will be displayed. Otherwise, the
phone number of the incoming call will
be displayed.
Say to call the number. Say
Entry Ž or Entry Ž to move
through the list of incoming calls.
Missed Calls
Speak this command to list the last five
missed calls to the vehicle. If the call is
from an entry in the phonebook, the
name will be displayed. Otherwise, the
phone number of the missed call will be
displayed.
Say to call the number. Say
Entry Ž or Entry Ž to move
through the list of missed calls.
Monitor, climate, audio, phone and voice recognition systems4-71
Page 198 of 372
button.
2. The system will prompt you for a com-
mand. Say
3. Select one of the available voice com-
mands to continue:
name)Ž „ Speak the name of a
phonebook entry to place a call to that
entry. The system will respond with the
name it interpreted from your com-
mand and will prompt you to confirm
that the name is correct. Say to
initiate the call or to hear another
name from the phonebook. NumberŽ „ Speak this com-
mand to place a call by inputting num-
bers. For 7… to 10…digit phone number,
speak the numbers. Say at
any time in the process to correct a
misspoken or misinterpreted number.
For phone numbers with more digits or
special characters, say Num-
berŽ, then speak the digits. Up to 24 dig-
its can be entered. Available special
characters are
and When finished, say to
initiate the call. Say at any
time in the process to correct a misspo-
ken or misinterpreted number or char-
acter.
… Speak this command to dial
the number of the last outgoing call.
The system will display
<name/number>Ž. The name of the
phonebook entry will be displayed if it
available, otherwise the number being
re-dialed will be displayed.
4-72Monitor, climate, audio, phone and voice recognition systems
Page 199 of 372
button to accept the call.
Press the
button to reject the call.
DURING A CALL
While a call is active, press thebutton
to access additional options. Speak one of
the following commands:
DigitsŽ … Speak numbers and then
say or say to change
the numbers entered.
OnŽ or Off Ž … Speak the
command to mute or unmute the sys-
tem. CallŽ … Speak this command to
transfer the call to the handset. To
transfer the call back from the handset
to the Bluetooth® Hands-Free Phone
System, press the
button and
confirm when prompted.
If supported by the phone, the Bluetooth®
Hands-Free Phone System allows for call
waiting functionality. If a call is received
while another call is already active, a mes-
sage will be displayed on the screen. Press
the
button to hold the active call and
switch to the second call. Press the
button to reject the second call.
While the second call is active, pressing
the
button will allow the same com-
mands that are available during any call
and additional commands:
CallŽ … Speak this command to
hold the second call and switch back to
the original call.
Other CallŽ … Speak this command
to stay with the second call and end the
original call.
Press the
button to accept the call.
Press the
button to reject the call.
ENDING A CALL
To end an active call, press thebut-
ton.
TEXT MESSAGING (if so equipped)
Page 200 of 372
button.
2. Say
3. Say TextŽ.
4. The system will provide a list of avail-
able commands in order to determine
the recipient of the text message.
Choose from the following:
(A name)
Number
Incoming Calls
Outgoing Calls
Missed Calls
If CallsŽ, CallsŽ, or
CallsŽ is selected, the following
additional commands will be dis-
played:
Send Text
Next Entry
Previous Entry
For additional information about these
options, refer to commandsŽ in
this section.5. Once a recipient is chosen, the system
prompts for which message to send.
Five predefined messages are avail-
able as well as three custom mes-
sages. To choose one of the predefined
messages, speak one of the following:
textŽ
meŽ
my way Ž
lateŽ
Ž
To send one of the custom messages, say
MessageŽ. If more than one cus-
tom message is stored, the system will
prompt for the number of the desired cus-
tom message. For additional information
on setting and managing custom text
messages, refer to settingsŽ in
this section.
Reading a received text message:
1. Press the
button.
2. Say “Messaging”.
3. Say “Read Text”.
The text message, sender and delivery
time are shown on the screen. Use the tun-
ing switch on the steering wheel to scroll
4-74Monitor, climate, audio, phone and voice recognition systems